Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY(for Manual Seat) › from 2016.03
RM3250E _58 Vehicle Interior _038071 SEAT _0185769 FRONT SEAT ASSEMBLY(for Manual Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Manual Seat)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:
·
B394717

Wear protective gloves. Sharp areas on the parts may injure your hands.

·

There is risk of injury.



HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedures listed below are for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 72201B 1.INSTALL SEAT TRACK HANDLE SUB-ASSEMBLY LH

a.

Attach the claw and install the seat track handle sub-assembly LH.

B413223


Hide 2.INSTALL OCCUPANT DETECTION ECU (w/ Occupant Detection ECU)

a.
B443509

Attach the claw to install the occupant detection ECU.


Hide 3.INSTALL FRONT SEAT WIRE RH (w/ Occupant Detection ECU)

a.
B445512

Attach the wire harness clamp.


b.
B443508C01
3.146,0.313 3.344,0.51 0.198,0.198 10 false *a
*a for Front Side


Attach the clamp.


c.
B443507C01
0.063,1.167 0.375,1.365 0.313,0.198 10 false *a
*a for Front Side


Attach the clamp.


d.
B443506C01
1.625,0.594 1.823,0.813 0.198,0.219 10 true *a
*a for Front Side


Attach the clamp.


e.
B443504C01
2.75,1.948 2.969,2.135 0.219,0.188 10 false *a
*a for Front Side


Connect the 2 connectors.


f.

Connect the 4 connectors and install front seat wire RH.

B443505


Hide 71052A 4.INSTALL FRONT SEAT CUSHION SPRING SUB-ASSEMBLY LH

a.
B413224C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


While rotating the part in install direction (1) shown in the illustration, attach the hook.


b.

Push in Install direction (2) shown in the illustration to attach the hook and install the front seat cushion spring sub-assembly LH.


Hide 71538A 5.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH

a.
B445495C01
0,0 0,0 false
*A w/ Vertical Adjuster
*B w/o Vertical Adjuster
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Push in installation direction (1) shown in the illustration to attach the guide.


b.

While expanding the part in installation direction (2) shown in the illustration, attach the claw.


c.

Install the front seat cushion edge protector LH with the screw.


Hide 71537G 6.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH

HINT:

Use the same procedure as for the LH side.


Hide 71874 7.INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (w/ Vertical Adjuster)

a.
B421098C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Push in the installation direction (1) shown in the illustration.


b.

Push in the installation direction (2) shown in the illustration to attach the clip.


c.
B421099C01
0,0 0,0 false
V113147

Install in this Direction


Push the guide in the installation direction shown in the illustration.


d.

Install the front seat lower cushion shield LH with the screw.


Hide 71873 8.INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (w/ Vertical Adjuster)

HINT:

Use the same procedure as for the LH side.


Hide 9.INSTALL SEAT COVER WIRE

a.
B442727N04
1.708,0.656 1.26,0.396 true 2.167,0.406 1.708,0.646 true 2.948,0.625 2.615,0.823 true 3.063,2 2.729,2.198 true 0.823,0.844 0.573,0.677 true 0.719,2.188 0.469,2.021 true 1.719,1.292 1.719,1.625 true 1.719,2.26 1.719,2.594 true 1.667,0.708 1.823,0.906 0.156,0.198 10 true A 2.99,0.51 3.146,0.708 0.156,0.198 10 true B 0.375,0.51 0.531,0.708 0.156,0.198 10 true B 1.677,1.646 1.833,1.844 0.156,0.198 10 true C 1.677,2.615 1.833,2.813 0.156,0.198 10 true D 0.271,1.833 0.427,2.031 0.156,0.198 10 true E 3.104,1.854 3.26,2.052 0.156,0.198 10 true E

Install the seat cover wire.

HINT:
·

There are service parts available for wires of 1000 mm (3.28 ft.) or longer and formed wires.


·

When a wire that is less than 1000 mm (3.28 ft.) in length is needed, cut and shape a 1000 mm (3.28 ft.) supplied wire into the dimensions shown in the illustration.


·

Refer to the precautions when creating a wire.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION



Length:
A 170 mm (6.70 in.)
B 150 mm (5.91 in.)
C 230 mm (9.06 in.)
D 270 mm (10.63 in.)
E 290 mm (11.42 in.)


HINT:
B376752

The dimensions shown in the illustration are the length.



Hide 71071S 10.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

HINT:
·

Refer to the precautions on wrinkles to avoid creating any on the separate type front seat cushion cover when installing the seat cover.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION


·

As shown in the illustration, fix all of the cover seam allowances in the same direction.

B394024N08
2.5,0.24 3.271,0.438 0.771,0.198 10 false A - A 4.656,0.302 5.427,0.5 0.771,0.198 10 false B - B 0.198,0.396 0.354,0.594 0.156,0.198 10 false A 0.51,0.583 0.656,0.75 0.146,0.167 10 true A 0.938,0.802 1.094,1 0.156,0.198 10 false B 1.26,1.063 1.656,1.406 0.396,0.344 10 false B



a.

Temporarily install the separate type front seat cushion cover to the separate type front seat cushion pad.


b.

Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 18 new hog rings in the order shown in the illustration.

B409602C01
5.25,2.177 5.323,1.667 false 4.969,0.927 5.115,0.938 true 5.115,0.844 5.427,1.042 0.313,0.198 10 false *a 5.167,2.229 5.479,2.427 0.313,0.198 10 false *1 1.99,1.771 2.208,1.979 0.219,0.208 10 true (1) 2.615,1.781 2.833,1.99 0.219,0.208 10 true (2) 1.979,1.156 2.198,1.365 0.219,0.208 10 true (3) 2.594,1.156 2.813,1.365 0.219,0.208 10 true (4) 1.365,1.844 1.635,2.052 0.271,0.208 10 true (10) 1.417,1.354 1.688,1.563 0.271,0.208 10 true (11) 1.448,1.104 1.729,1.313 0.281,0.208 10 true (12) 1.448,0.792 1.729,1 0.281,0.208 10 true (13) 1.49,0.51 1.75,0.719 0.26,0.208 10 true (14) 3.146,1.844 3.365,2.052 0.219,0.208 10 true (5) 3.135,1.365 3.354,1.573 0.219,0.208 10 true (6) 3.135,1.125 3.354,1.333 0.219,0.208 10 true (7) 3.125,0.833 3.344,1.042 0.219,0.208 10 true (8) 3.104,0.563 3.323,0.771 0.219,0.208 10 true (9) 1.802,0.177 2.073,0.385 0.271,0.208 10 true (18) 2.125,0.177 2.385,0.385 0.26,0.208 10 true (17) 2.427,0.177 2.688,0.385 0.26,0.208 10 true (16) 2.75,0.177 3.021,0.417 0.271,0.24 10 true (15)
*1 Hog Ring Pliers - -
*a Cutout - -


NOTICE:
·

Do not dirty or damage the separate type front seat cushion cover.


·

Securely tighten the hog rings as shown in the illustration while making sure wrinkles do not form in the center of the fabric and separate type front seat cushion pad.



HINT:

Install the hog rings at the cutouts if they are there.



c.

Using hog ring pliers, connect the 2 straps of the separate type front seat cushion cover to the separate type front seat cushion pad with 2 new hog rings.

B413228C01
4.927,2.083 5.156,1.563 false 4.771,2.125 5.083,2.323 0.313,0.198 10 false *1
*1 Hog Ring Pliers - -


NOTICE:
·

Do not dirty or damage the separate type front seat cushion cover.


·

Securely tighten the hog rings as shown in the illustration while making sure wrinkles do not form in the center of the fabric and separate type front seat cushion pad.




Hide 11.INSTALL SEAT CUSHION COVER WITH PAD

a.

While sliding the part in the direction indicated by the arrow shown in the illustration, align the J hook to install the seat cushion cover with pad.

B413217


Hide 71587B 12.INSTALL FRONT SEATBACK EDGE PROTECTOR (for Low-back Seat Type)

a.
B409604

Attach the claw to Install the 2 front seatback edge protectors.


Hide 71054S 13.INSTALL FRONT SEATBACK SPRING SUB-ASSEMBLY LH (for Low-back Seat Type)

a.
B421100C01
1.875,1.323 2.677,0.927 true 0.448,1.292 1.406,1.406 true 2.74,0.833 3.052,1.031 0.313,0.198 10 false *1 0.198,1.208 0.51,1.406 0.313,0.198 10 false *1
*1 Front No. 2 Seatback Hook
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Temporarily install the 2 front No. 2 seatback hooks to the front seatback spring sub-assembly LH.


b.

Push in installation direction (1) shown in the illustration to install the front seatback spring sub-assembly LH.


c.

Push in installation direction (2) shown in the illustration to temporarily the front seatback spring sub-assembly LH.


d.
B403873

Attach the claw and install the 2 front seatback edge protectors.


Hide 71759D 14.INSTALL FRONT NO. 2 SEATBACK HOOK (for Low-back Seat Type)

a.
B413216C01
0,0 0,0 false
V113147

Install in this Direction


Push up installation direction shown in the illustration to attach the claw to install the 2 front No. 2 seatback hooks.


Hide 73920A 15.INSTALL FRONT SEAT AIRBAG ASSEMBLY LH (w/ Front Seat Side Airbag)

Hide 16.INSTALL SEAT COVER WIRE

a.

Install the seat cover wire.

HINT:
·

There are service parts available for wires of 1000 mm (3.28 ft.) or longer and formed wires.


·

When a wire that is less than 1000 mm (3.28 ft.) in length is needed, cut and shape a 1000 mm (3.28 ft.) supplied wire into the dimensions shown in the illustration.


·

Refer to the precautions when creating a wire.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION



i.
B402134N04
1.938,1.042 2.656,0.552 true 2.104,1.823 2.823,1.333 true 2.115,2.917 2.833,2.427 true 0.656,3.115 1.24,2.885 true 2.75,0.406 2.906,0.604 0.156,0.198 10 false A 2.927,1.229 3.083,1.427 0.156,0.198 10 false B 2.948,2.323 3.104,2.521 0.156,0.198 10 false C 0.458,3.063 0.615,3.26 0.156,0.198 10 false C

for Hi-back Seat Type:

Length:
A 150 mm (5.91 in.)
B 290 mm (11.42 in.)
C 420 mm (1.38 ft.)


HINT:
B376752

The dimensions shown in the illustration are the length.



ii.
B413333N01
1.969,1.365 2.917,1.115 true 2.333,2.969 2.885,3.021 true 2.313,3.198 2.896,3.021 true 2.99,1.021 3.146,1.219 0.156,0.198 10 true A 2.958,2.938 3.115,3.135 0.156,0.198 10 true B

for Low-back Seat Type, for Basic Style:

Length:
A 290 mm (11.42 in.)
B 420 mm (1.38 ft.)


HINT:
B376752

The dimensions shown in the illustration are the length.



iii.
B413213N01
2.365,1.094 3.031,0.896 true 0.792,0.49 1.375,0.802 true 1.76,1.333 1.885,1.021 true 2.313,3.208 2.854,2.958 true 2.323,3.031 2.844,2.958 true 0.625,0.396 0.781,0.594 0.156,0.198 10 false A 3.125,0.771 3.281,0.969 0.156,0.198 10 false A 1.833,0.844 1.99,1.042 0.156,0.198 10 true B 2.958,2.865 3.115,3.063 0.156,0.198 10 false C

for Low-back Seat Type, for High Style:

Length:
A 170 mm (6.70 in.)
B 200 mm (7.87 in.)
C 420 mm (1.38 ft.)


HINT:
B376752

The dimensions shown in the illustration are the length.




Hide 71073S 17.INSTALL SEPARATE TYPE FRONT SEATBACK COVER

HINT:
·

Refer to the precautions on wrinkles to avoid creating any on the separate type front seatback cover when installing the seat cover.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION


·

As shown in the illustration, fix all of the cover seam allowances in the same direction.

B394023N01
0.542,0.354 0.698,0.552 0.156,0.198 10 false A 0.813,0.458 0.969,0.656 0.156,0.198 10 false A 1.177,0.583 1.333,0.781 0.156,0.198 10 false B 1.5,0.719 1.656,0.917 0.156,0.198 10 true B 1.125,0.052 1.281,0.25 0.156,0.198 10 false C 0.813,0.24 0.969,0.438 0.156,0.198 10 true C 2.042,0.229 2.813,0.427 0.771,0.198 10 false A - A 3.438,0.24 4.208,0.438 0.771,0.198 10 false C - C 5.615,0.281 6.385,0.479 0.771,0.198 10 false B - B



a.

Set the separate type front seatback cover.


b.

for Hi-back Seat Type:

i.

Using hog ring pliers, install the separate type front seatback cover with 8 new hog rings in the order shown in the illustration.

B413335C01
5.125,0.948 4.979,0.927 true 3.448,0.729 2.833,0.885 true 2.5,0.875 2,0.719 true 2.229,1.115 1.729,0.958 true 3.688,1.021 3.073,1.177 true 3.365,1.979 2.76,1.417 true 3.365,1.969 3.031,1.458 true 1.604,1.552 2.25,1.333 true 1.625,1.542 2.458,1.375 true 5.25,2.125 5.354,1.656 true 5.156,2.146 5.469,2.344 0.313,0.198 10 false *1 5.115,0.844 5.427,1.042 0.313,0.198 10 false *a 1.781,0.583 2.031,0.802 0.25,0.219 10 false (1) 3.5,0.573 3.75,0.792 0.25,0.219 10 false (1) 3.75,0.896 4,1.115 0.25,0.219 10 false (2) 1.531,0.823 1.781,1.042 0.25,0.219 10 false (2) 1.385,1.448 1.635,1.667 0.25,0.219 10 false (3) 3.438,2 3.688,2.219 0.25,0.219 10 false (3)
*1 Hog Ring Pliers - -
*a Cutout - -


NOTICE:
·

Do not dirty or damage the separate type front seatback cover.


·

Securely tighten the hog rings as shown in the illustration while making sure wrinkles do not form in the center of the fabric and separate type front seatback pad.



HINT:

Install the hog rings at the cutouts if they are there.




c.

for Low-back Seat Type, Basic Style:

i.

Using hog ring pliers, install the separate type front seatback cover with 6 new hog rings in the order shown in the illustration.

B409606C01
5.25,2.229 5.24,1.646 true 5.094,0.948 4.958,0.938 true 3.417,0.427 3.063,0.719 true 1.74,0.302 2,0.563 true 1.563,0.802 1.979,1.188 true 1.563,0.792 2.271,1.156 true 2.75,1.219 3.365,1.146 true 2.927,1.375 3.365,1.156 true 5.115,0.854 5.427,1.052 0.313,0.198 10 false *a 5.198,2.281 5.51,2.479 0.313,0.198 10 false *1 3.417,0.229 3.875,0.427 0.458,0.198 10 false (1) 1.563,0.135 2.021,0.333 0.458,0.198 10 false (1) 1.365,0.677 1.823,0.875 0.458,0.198 10 false (2) 3.417,1.052 3.875,1.25 0.458,0.198 10 false (2)
*1 Hog Ring Pliers - -
*a Cutout - -


NOTICE:
·

Do not dirty or damage the separate type front seatback cover.


·

Securely tighten the hog rings as shown in the illustration while making sure wrinkles do not form in the center of the fabric and separate type front seatback pad.



HINT:

Install the hog rings at the cutouts if they are there.




d.

for Low-back Seat Type, High Style:

i.

Using hog ring pliers, install the separate type front seatback cover with 12 new hog rings in the order shown in the illustration.

B413336C01
5.375,2.24 5.344,1.667 true 5.094,0.917 4.969,0.938 true 3.604,1.052 2.958,1.146 true 3.615,1.073 3.063,0.74 true 1.979,0.604 1.333,0.698 true 2,1.031 1.344,0.698 true 2.333,1.156 2.677,0.26 true 2.646,1.25 2.667,0.271 true 3.531,2.292 2.729,2.438 true 3.531,2.292 2.781,2.188 true 3.542,2.313 2.896,1.521 true 1,1.75 1.938,1.333 true 0.979,1.75 1.792,1.927 true 1.021,1.76 1.74,2.26 true 5.313,2.292 5.625,2.49 0.313,0.198 10 false *1 5.104,0.833 5.417,1.031 0.313,0.198 10 false *a 3.698,1.021 4.156,1.219 0.458,0.198 10 false (1) 1.115,0.615 1.573,0.813 0.458,0.198 10 false (1) 2.604,0.073 3.063,0.271 0.458,0.198 10 false (2) 0.76,1.656 1.219,1.854 0.458,0.198 10 false (3) 3.646,2.25 4.104,2.448 0.458,0.198 10 false (3)
*1 Hog Ring Pliers - -
*a Cutout - -


NOTICE:
·

Do not dirty or damage the separate type front seatback cover.


·

Securely tighten the hog rings as shown in the illustration while making sure wrinkles do not form in the center of the fabric and separate type front seatback pad.



HINT:

Install the hog rings at the cutouts if they are there.




Hide 18.INSTALL SEATBACK COVER WITH PAD

a.

for Hi-back Seat Type:

i.
B402131C01
0,0 0,0 false
V113147

Install in this Direction


Push in installation direction shown in the illustration to temporarily install the seatback cover with pad.



b.

for Low-back Seat Type:

i.
B415862C01
0,0 0,0 false
V113147

Install in this Direction


Push in installation direction shown in the illustration to temporarily install the seatback cover with pad.



c.

w/ Front Seat Side Airbag, for Type B:

i.
B413233C01
1.813,2.979 2.625,2.688 true 0.479,1.667 1.469,1.76 true 0.292,1.594 0.604,1.792 0.313,0.198 10 false *1 2.677,2.563 2.99,2.76 0.313,0.198 10 false *2
*1 J Hook A
*2 J Hook B
V113147

Install in this Direction


Push in the installation direction shown in the illustration to attach the J hook A and J hook B.

HINT:

For RH seats, push up from below.



ii.
B413563C01
2.021,1.333 2.49,0.677 true 0.958,3.135 1.26,2.896 true 0.729,3.073 1.042,3.271 0.313,0.198 10 false *1 2.479,0.51 2.792,0.708 0.313,0.198 10 false *2
*1 J Hook B (J Hook A and J Hook B)
*2 J Hook C
V113147

Install in this Direction


Push in the installation direction shown in the illustration to attach the J hook B (J hook A and J hook B) and J hook C.

HINT:

For RH seats, push up from below.



iii.

Install the new rivet to J hook B.

B413208C01
2.219,1.656 3.104,1.177 true 0.74,1.75 1.854,1.729 true 5.542,1.771 6.625,1.656 true 4.229,1.135 5.208,1.583 true 0.094,0.094 0.406,0.292 0.313,0.198 10 false *A 3.604,0.146 3.917,0.344 0.313,0.198 10 false *B 0.542,1.677 0.854,1.875 0.313,0.198 10 false *1 6.688,1.542 7,1.74 0.313,0.198 10 false *1 3.167,1.063 3.479,1.26 0.313,0.198 10 false *2 4.021,1.063 4.333,1.26 0.313,0.198 10 false *2
*A for LH seat *B for RH seat
*1 J Hook A *2 J Hook B


HINT:
·

For LH seats, install the top rivet.


·

For RH seats, install the bottom rivet.




iv.

Place your hand at the position shown in the illustration and push in the install direction to attach the J hook B.

B413236C01
2.354,1.417 2.771,1 true 1.25,2.208 1.99,1.635 true 1.615,0.917 1.417,0.646 true 1.281,0.49 1.594,0.688 0.313,0.198 10 false *3 2.813,0.875 3.125,1.073 0.313,0.198 10 false *2 1.031,2.177 1.344,2.375 0.313,0.198 10 false *1
*1 J Hook A *2 J Hook B
*3 J Hook C - -
V113146

Place Hand Here
V113147

Install in this Direction




d.

for Hi-back Seat Type:

i.

Using hog ring pliers, install the 2 new hog rings.

B445551C01
5.323,2.229 5.385,1.781 false 5.24,2.313 5.552,2.51 0.313,0.198 10 false *1
*1 Hog Ring Pliers - -



ii.

Using hog ring pliers, install the 6 new hog rings.

B449438C01
5.156,2.198 5.26,1.646 false 4.938,0.906 5.104,0.906 true 5.083,2.219 5.396,2.375 0.313,0.156 10 false *1 5.125,0.813 5.438,0.969 0.313,0.156 10 false *a
*1 Hog Ring Pliers - -
*a Cutout - -


NOTICE:
·

Do not dirty or damage the separate type front seatback cover.


·

Securely tighten the hog rings as shown in the illustration while making sure wrinkles do not form in the center of the fabric and separate type front seatback pad.



HINT:

Install the hog rings at the cutouts if they are there.




Hide 71931 19.INSTALL FRONT SEAT HEADREST SUPPORT (for Low-back Seat Type)

a.
B403861C01
0,0 0,0 false
V113147

Install in this Direction


Push in the installation direction shown in the illustration to attach the claw and install the 2 front seat headrest supports.


b.
B413205C01
0,0 0,0 false
V113147

Install in this Direction


for Basic Style:

i.

Pull up the installation direction shown in the illustration to attach the guide to the 2 straps.



c.
B413232C01
0,0 0,0 false
V113147

Install in this Direction


Close the fasteners as shown in the illustration.


d.

Using hog ring pliers, install 6 new hog rings.

B443666C07
5.292,1.656 5.344,2.375 false 4.938,0.917 5.094,0.917 true 5.281,2.396 5.594,2.552 0.313,0.156 10 false *1 5.125,0.823 5.438,0.979 0.313,0.156 10 false *a
*1 Hog Ring Pliers - -
*a Cutout - -


NOTICE:
·

Do not dirty or damage the separate type front seatback cover.


·

Securely tighten the hog rings as shown in the illustration while making sure wrinkles do not form in the center of the fabric and separate type front seatback pad.



HINT:

Install the hog rings at the cutouts if they are there.



Hide 71759C 20.INSTALL FRONT NO. 1 SEATBACK HOOK (for Low-back Seat Type)

a.
B416134

Install the claw and front No. 1 seatback hook.


Hide 71876F 21.INSTALL RECLINING ADJUSTER INSIDE COVER LH

a.
B413242C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Push down installation direction (1) shown in the illustration.


b.

Rotate the part in installation direction (2) shown in the illustration and align the guide to install the reclining adjuster inside cover LH.


Hide 71875E 22.INSTALL RECLINING ADJUSTER INSIDE COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 71014S 23.INSTALL FRONT SEATBACK FRAME SUB-ASSEMBLY LH

a.
B413201C01
0.094,0.094 0.406,0.292 0.313,0.198 10 false *A 0.156,2.25 0.469,2.448 0.313,0.198 10 false *B
*A RH Side
*B LH Side


Install the 4 bolts and front seatback frame sub-assembly LH.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


b.
B416712C01
1.208,2.052 2.208,1.583 true 0.875,3.792 2.323,4.469 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *A 0.094,2.219 0.406,2.417 0.313,0.198 10 false *B 0.99,1.969 1.302,2.167 0.313,0.198 10 false *1 2.417,4.365 2.729,4.563 0.313,0.198 10 false *1
*A RH Side
*B LH Side
*1 Separate Type Front Seat Cushion Cover


Attach the hook.


c.
B412647

w/ Front Seat Side Airbag, w/ Seat Heater System:

i.

Attach the wire harness clamp and wire harness connector.



d.
B412646

w/ Front Seat Side Airbag, w/o Seat Heater System:

i.

Attach the wire harness clamp.



e.
B412645

w/o Front Seat Side Airbag, w/ Seat Heater System:

i.

Attach the wire harness clamp and wire harness connector.



f.
B412644C01
1.458,2.125 2.052,2.448 true 1.438,1.792 1.885,1.708 true 1.063,1.375 1.5,1.094 true 0.938,0.99 1.5,1.094 true 2.115,2.354 2.344,2.583 0.229,0.229 10 true *2 1.917,1.615 2.146,1.844 0.229,0.229 10 true *1 1.563,0.958 1.792,1.188 0.229,0.229 10 true *1
*1 Wire Harness Clamp
*2 Connector Clamp


w/ Front Seat Side Airbag:

i.

Attach the wire harness clamp and connector clamp.



g.
B412643C01
1.896,3.833 2.406,4.198 true 2.427,3.365 2.885,3.365 true 1.5,2.833 2.135,2.688 true 1.521,2.844 2.146,3.042 true 1.521,2.833 1.885,3.438 true 2.406,0.865 2.76,0.958 true 1.938,1.385 2.25,1.635 true 1.354,0.417 1.844,0.979 true 1.365,0.427 2.146,0.583 true 1.365,0.427 2.146,0.188 true 0.042,0.073 0.292,0.292 0.25,0.219 10 true *A 0.052,2.438 0.302,2.656 0.25,0.219 10 true *B 2.427,4.188 2.677,4.406 0.25,0.219 10 true *3 1.229,2.75 1.479,2.969 0.25,0.219 10 true *1 2.917,3.26 3.167,3.479 0.25,0.219 10 true *2 2.313,1.573 2.563,1.792 0.25,0.219 10 true *3 2.802,0.896 3.052,1.115 0.25,0.219 10 true *2 1.156,0.323 1.406,0.542 0.25,0.219 10 true *1
*A w/o Front Seat Side Airbag
*B w/ Front Seat Side Airbag
*1 Wire Harness Clamp
*2 Guide
*3 Connector Clamp


w/ Seat Heater System:

i.

Attach the wire harness clamp, connector clamp and guide.



h.
B413198

Install the band in the position shown in the illustration.


Hide 73240 24.INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

Hide 71862 25.INSTALL FRONT SEAT INNER CUSHION SHIELD LH

a.
B413247C01
0,0 0,0 false
V113147

Install in this Direction


Push in the installation direction shown in the illustration to attach the claw and guide.


b.
B413248C01
0,0 0,0 false
V113147

Install in this Direction


Push in installation direction shown in the illustration and attach the claw to install the front seat inner cushion shield LH.


Hide 71812D 26.INSTALL FRONT SEAT CUSHION SHIELD LH

a.
B445496C01
0,0 0,0 false
V113147

Install in this Direction


Push in the installation direction shown in the illustration to attach the claw and guide.


b.
B445497C01
0,0 0,0 false
V113147

Install in this Direction


Push in the installation direction shown in the illustration to attach the claw and guide.


c.
B445489C01
2.396,2.656 2.875,1.875 true 1.125,2.521 1.156,2 true 2.875,1.708 3.188,1.906 0.313,0.198 10 false *1 1.156,1.844 1.469,2.042 0.313,0.198 10 false *2
*1 Clip A
*2 Clip B


Attach the clip B.


d.

Attach the claw.


e.

Attach the clip A and install the front seat cushion shield RH.


Hide 72495 27.INSTALL VERTICAL ADJUSTING HANDLE LH (w/ Vertical Adjuster)

a.
B445499C01
0,0 0,0 false
V113147

Install in this Direction


With the reclining adjuster release handle LH pulled up.


b.

Attach the guide, and then push in the installation direction shown in the illustration to install the vertical adjusting handle LH.


c.
B445500

Install the screw.


Hide 72526E 28.INSTALL RECLINING ADJUSTER RELEASE HANDLE LH

a.
B445501C01
0,0 0,0 false
V113147

Install in this Direction


With the reclining adjuster release handle LH pulled up.


b.

Push in the installation direction shown in the illustration and attach the claw to install the reclining adjuster release handle LH.


Hide 71849 29.INSTALL SEAT ADJUSTER COVER CAP LH

a.
B413258C01
0,0 0,0 false
V113147

Install in this Direction


Push in the installation direction shown in the illustration to install the 2 seat adjuster cover caps LH.


Hide 71910A 30.INSTALL FRONT SEAT HEADREST ASSEMBLY (for Low-back Seat Type)

a.
B411002C01
0,0 0,0 false
V100136

Apply Silicon


Apply silicon lubricant to the application area.

HINT:

The application area shown in the illustration is 20 + / -10 mm.



b.

Install the front seat headrest assembly.