Home › Engine / Hybrid System › 2GD-FTV ENGINE CONTROL › ECD SYSTEM(w/ Urea SCR System) › from 2016.08
RM3250E _51 Engine / Hybrid System _038005 2GD-FTV ENGINE CONTROL _0262511 ECD SYSTEM(w/ Urea SCR System) C

2GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, the ECM detects the starter signal (STA signal) and performs engine control when the engine starts.

If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle has been driven at 20 km/h (12.5 mph) or more for more than 20 seconds.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High Conditions (a), (b) and (c) are met for 20 seconds (1 trip detection logic):
(a) Vehicle speed is more than 20 km/h (12.5 mph).
(b) Engine speed is more than 1000 rpm.
(c) STA signal is on.
·

ST NO. 1 relay circuit*1

·

ST NO. 2 relay circuit*2

·

Ignition switch assembly

·

Park/Neutral position switch assembly

·

Clutch start switch assembly

·

Engine stop and start ECU

·

ECM


Comes on DTC stored

*1: w/o Entry and Start System

*2: w/ Entry and Start System

Related Data List
DTC No. Data List
P0617 Starter Signal

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0617 Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more

WIRING DIAGRAM

w/ Entry and Start System and w/ Stop and Start System
A382142E01
0.74,0.333 1.031,0.552 0.292,0.219 10 false NE 0.594,0.708 1.042,0.927 0.448,0.219 10 false STA2 0.677,1.094 1.031,1.313 0.354,0.219 10 false CLL 0.656,1.458 1.021,1.677 0.365,0.219 10 false STA 0.198,1.938 2.115,2.125 1.917,0.188 10 false Engine Stop and Start ECU 0.198,1.76 0.563,1.979 0.365,0.219 10 false G126 1.031,0.469 1.396,0.688 0.365,0.219 10 false 10 1.052,1.208 1.417,1.427 0.365,0.219 10 false 17 1.052,0.844 1.417,1.063 0.365,0.219 10 false 23 1.052,1.583 1.417,1.802 0.365,0.219 10 false 21 0.156,3.958 1.958,4.323 1.802,0.365 10 false Certification ECU (Smart Key ECU Assembly) 0.667,3.583 1.031,3.802 0.365,0.219 10 false STA 6.26,0.729 6.708,0.948 0.448,0.219 10 false STA 0.719,2.708 1.01,2.927 0.292,0.219 10 false NE 1.042,2.708 1.49,2.927 0.448,0.219 10 false G69 1.125,2.521 1.417,2.74 0.292,0.219 10 false 6 1.083,2.927 1.375,3.146 0.292,0.219 10 false 16 1.083,3.396 1.375,3.615 0.292,0.219 10 false 37 1.042,3.125 1.49,3.344 0.448,0.219 10 false G70 1.052,3.594 1.5,3.813 0.448,0.219 10 false G70 2.896,4.167 5.354,4.385 2.458,0.219 10 false Park/Neutral Position Switch Assembly 2.896,3.99 3.26,4.208 0.365,0.219 10 false C24 4.448,3.708 4.74,3.927 0.292,0.219 10 false 4 3.365,3.708 3.656,3.927 0.292,0.219 10 false 5 4.448,4.958 4.74,5.177 0.292,0.219 10 false 2 3.385,4.948 3.677,5.167 0.292,0.219 10 false 1 4.24,3.479 4.479,3.677 0.24,0.198 10 false B 3.583,3.479 3.823,3.677 0.24,0.198 10 false L 3.281,5.344 5.188,5.594 1.906,0.25 10 false Clutch Start Switch Assembly 3.281,5.177 3.646,5.396 0.365,0.219 10 false B2 6.406,2.448 6.771,2.667 0.365,0.219 10 false ECM 6.396,2.292 6.76,2.51 0.365,0.219 10 false G85 6.25,0.344 6.708,0.563 0.458,0.219 10 false NEO 5.979,0.479 6.344,0.698 0.365,0.219 10 false 23 5.99,0.844 6.354,1.063 0.365,0.219 10 false 22 5.99,1.229 6.354,1.448 0.365,0.219 10 false 11 6.271,1.094 6.719,1.313 0.448,0.219 10 false NSW 0.542,3.115 0.99,3.333 0.448,0.219 10 false STAR 2.958,6.354 3.688,6.594 0.729,0.24 10 false ST NO. 1 5.896,6.375 6.708,6.563 0.813,0.188 10 false ST NO. 2 3.594,5.854 4.406,6.042 0.813,0.188 10 false ST NO. 2 1,6.042 1.729,6.281 0.729,0.24 10 false ST NO. 1 0.531,6.865 1.26,7.104 0.729,0.24 10 false FL MAIN 0.615,8.177 1.344,8.417 0.729,0.24 10 false Battery 2.771,8.385 4.667,8.615 1.896,0.229 10 false Starter Assembly 1.5,7.75 1.865,7.969 0.365,0.219 10 false D3 1.531,7.531 1.823,7.75 0.292,0.219 10 false 1 2.531,7.396 2.823,7.615 0.292,0.219 10 false 1 4.604,7.406 4.896,7.625 0.292,0.219 10 false 2 5.5,7.396 5.792,7.615 0.292,0.219 10 false 1 1.802,7.75 2.167,7.969 0.365,0.219 10 false B 2.188,7.646 2.552,7.865 0.365,0.219 10 false SL1 4.229,7.646 4.594,7.865 0.365,0.219 10 false SL2 5.177,7.646 5.542,7.865 0.365,0.219 10 false ST 2.135,7.396 2.5,7.615 0.365,0.219 10 false C141 4.208,7.406 4.573,7.625 0.365,0.219 10 false C141 5.104,7.396 5.469,7.615 0.365,0.219 10 false C140 3.052,3.458 3.417,3.677 0.365,0.219 10 false *1 3.031,4.677 3.396,4.896 0.365,0.219 10 false *2 4.844,3.448 5.208,3.667 0.365,0.219 10 false *1 4.813,4.646 5.177,4.865 0.365,0.219 10 false *2 0.104,4.958 2.052,5.167 1.948,0.208 10 false *1: for Automatic Transmission 0.115,5.292 1.99,5.5 1.875,0.208 10 false *2: for Manual Transmission

w/o Entry and Start System and w/ Stop and Start System
A382143E01
0.188,2.031 1.938,2.281 1.75,0.25 10 false Engine Stop and Start ECU 0.177,1.844 0.646,2.042 0.469,0.198 10 false G126 0.729,0.344 1.198,0.542 0.469,0.198 10 false NE 0.594,0.719 1.063,0.917 0.469,0.198 10 false STA2 0.677,1.104 1.146,1.302 0.469,0.198 10 false CLL 0.646,1.458 1.115,1.656 0.469,0.198 10 false STA 1.042,0.479 1.51,0.677 0.469,0.198 10 false 10 1.042,0.854 1.51,1.052 0.469,0.198 10 false 23 1.042,1.229 1.51,1.427 0.469,0.198 10 false 17 1.052,1.583 1.521,1.781 0.469,0.198 10 false 21 5.99,0.479 6.458,0.677 0.469,0.198 10 false 23 5.99,0.823 6.458,1.021 0.469,0.198 10 false 22 5.99,1.208 6.458,1.406 0.469,0.198 10 false 11 6.26,0.365 6.729,0.563 0.469,0.198 10 false NEO 6.271,0.719 6.74,0.917 0.469,0.198 10 false STA 6.271,1.094 6.74,1.292 0.469,0.198 10 false NSW 6.375,2.271 6.844,2.469 0.469,0.198 10 false G85 6.385,2.458 6.854,2.656 0.469,0.198 10 false ECM 2.813,4.188 5.406,4.417 2.594,0.229 10 false Park/Neutral Position Switch Assembly 3.26,5.333 5.219,5.583 1.958,0.25 10 false Clutch Start Switch Assembly 2.823,4.01 3.292,4.208 0.469,0.198 10 false C24 4.448,3.708 4.917,3.906 0.469,0.198 10 false 4 3.344,3.719 3.813,3.917 0.469,0.198 10 false 5 4.208,3.469 4.677,3.667 0.469,0.198 10 false B 3.594,3.469 4.063,3.667 0.469,0.198 10 false L 4.448,4.948 4.917,5.146 0.469,0.198 10 false 2 3.354,4.948 3.823,5.146 0.469,0.198 10 false 1 3.26,5.167 3.729,5.365 0.469,0.198 10 false B2 0.802,3.781 2.479,4.042 1.677,0.26 10 false Ignition Switch Assembly 0.802,3.635 1.271,3.833 0.469,0.198 10 false G1 0.948,3 1.417,3.198 0.469,0.198 10 false AM2 1.667,2.99 2.135,3.188 0.469,0.198 10 false ST2 0.74,3.24 1.208,3.438 0.469,0.198 10 false 4 2.031,3.24 2.5,3.438 0.469,0.198 10 false 2 0.531,5.094 2.208,5.354 1.677,0.26 10 false STRG LOCK/AM2 NO. 1 0.99,6.073 1.656,6.292 0.667,0.219 10 false ST NO. 1 2.958,6.406 3.625,6.625 0.667,0.219 10 false ST NO. 1 3.604,5.833 4.271,6.052 0.667,0.219 10 false ST NO. 2 5.885,6.417 6.552,6.635 0.667,0.219 10 false ST NO. 2 0.635,8.156 1.302,8.375 0.667,0.219 10 false Battery 0.552,6.875 1.219,7.094 0.667,0.219 10 false FL MAIN 1.479,7.75 2.146,7.969 0.667,0.219 10 false D3 2.135,7.406 2.802,7.625 0.667,0.219 10 false C141 4.208,7.396 4.875,7.615 0.667,0.219 10 false C141 5.104,7.396 5.771,7.615 0.667,0.219 10 false C140 2.563,7.385 3.031,7.583 0.469,0.198 10 false 1 1.542,7.563 2.01,7.76 0.469,0.198 10 false 1 5.531,7.396 6,7.594 0.469,0.198 10 false 1 4.625,7.396 5.094,7.594 0.469,0.198 10 false 2 1.802,7.76 2.469,7.979 0.667,0.219 10 false B 2.167,7.646 2.833,7.865 0.667,0.219 10 false SL1 4.25,7.646 4.917,7.865 0.667,0.219 10 false SL2 5.188,7.646 5.854,7.865 0.667,0.219 10 false ST 2.531,8.365 4.302,8.583 1.771,0.219 10 false Starter Assembly 3.052,3.469 3.521,3.667 0.469,0.198 10 false *1 4.854,3.458 5.323,3.656 0.469,0.198 10 false *1 4.844,4.677 5.313,4.875 0.469,0.198 10 false *2 3.021,4.698 3.49,4.896 0.469,0.198 10 false *2 2.844,2.24 5.438,2.469 2.594,0.229 10 false *1: for Automatic Transmission 2.865,2.583 5.458,2.813 2.594,0.229 10 false *2: for Manual Transmission

w/o Entry and Start System and w/o Stop and Start System
A360758E02
0.625,1.198 0.938,1.396 0.313,0.198 10 false G1 0.635,1.365 2.24,1.594 1.604,0.229 10 false Ignition Switch Assembly 0.542,0.667 0.854,0.865 0.313,0.198 10 false 4 1.823,0.667 2.135,0.865 0.313,0.198 10 false 2 0.74,0.667 1.115,0.844 0.375,0.177 10 false AM2 1.469,0.667 1.844,0.844 0.375,0.177 10 false ST2 2.948,1.375 3.26,1.573 0.313,0.198 10 false 2 2.927,2.458 3.24,2.656 0.313,0.198 10 false 4 4.052,2.458 4.365,2.656 0.313,0.198 10 false 5 4.042,1.375 4.354,1.573 0.313,0.198 10 false 1 2.219,2.823 2.635,3.021 0.417,0.198 10 false C24 3.115,1.833 3.427,2.031 0.313,0.198 10 false B2 2.229,3 4.885,3.24 2.656,0.24 10 false Park/Neutral Position Switch Assembly*2 3.104,2.01 4.708,2.24 1.604,0.229 10 false Clutch Start Switch*1 5.208,0.781 5.521,0.979 0.313,0.198 10 false G85 5.208,3.542 5.521,3.74 0.313,0.198 10 false G85 5.24,0.594 5.552,0.792 0.313,0.198 10 false 11 5.24,3.365 5.552,3.563 0.313,0.198 10 false 22 5.583,0.781 6.063,0.979 0.479,0.198 10 false NSW 5.583,3.552 6.063,3.75 0.479,0.198 10 false STA 1.604,5.958 3.208,6.188 1.604,0.229 10 false Starter Assembly 1.406,5.49 1.719,5.688 0.313,0.198 10 false D3 1.948,5.01 2.26,5.208 0.313,0.198 10 false C32 1.969,5.219 2.281,5.417 0.313,0.198 10 false ST 1.708,5.479 2.021,5.677 0.313,0.198 10 false B 2.115,4.802 2.427,5 0.313,0.198 10 false 1 1.427,5.292 1.74,5.49 0.313,0.198 10 false 1 2.677,4.594 2.99,4.792 0.313,0.198 10 false 1 2.688,3.813 3,4.01 0.313,0.198 10 false 2 1.938,3.813 2.25,4.01 0.313,0.198 10 false 5 1.927,4.594 2.24,4.792 0.313,0.198 10 false 3 2.844,4.198 3.5,4.406 0.656,0.208 10 false ST NO. 1 0.896,3.708 1.552,3.917 0.656,0.208 10 false ST NO. 1 0.448,4.552 1.51,4.771 1.063,0.219 10 false FL MAIN 3.0W 5.917,4.823 6.573,5.031 0.656,0.208 10 false ECM 0.521,5.885 1.177,6.094 0.656,0.208 10 false Battery 0.406,2.135 2.01,2.365 1.604,0.229 10 false STRG LOCK/AM2 NO. 1 3.25,5.396 5.906,5.635 2.656,0.24 10 false *1: for Manual Transmission 3.25,5.688 5.906,5.927 2.656,0.24 10 false *2: for Automatic Transmission

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

Read Starter Count before replacing the engine stop and start ECU, perform the replacement procedure, and then write Starter Count to the newly installed engine stop and start ECU.

·

When replacing the engine stop and start ECU or the air conditioning amplifier assembly, initialize and learn the engine stop and start ECU air conditioning information.

·

When replacing the engine stop and start ECU or airbag ECU assembly (G sensor), initialize and learn the engine stop and start ECU G sensor zero point learned information.



HINT:
·

The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to Problem Symptoms Table (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ Urea SCR System)>PROBLEM SYMPTOMS TABLE).

·

If this DTC is output, inspect the starter assembly.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Starter Signal.

Powertrain > Engine > Data List
Tester Display
Starter Signal
50003 234 118

d.

Read the value displayed on the GTS when the vehicle is driven at 20 km/h (12.4 mph) or more with engine speed at 1000 rpm or more.

Result:
Result Proceed to
Driving at 20 km/h (12.4 mph) or more with engine speed at 1000 rpm or more OFF A
ON w/ Stop and Start System B
w/o Stop and Start System for automatic transmission C
for manual transmission D




A

B

2.INSPECT ENGINE STOP AND START ECU

C

5.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

D

10.INSPECT CLUTCH START SWITCH
2.INSPECT ENGINE STOP AND START ECU
a.

Start the engine.


b.

Measure the voltage according to the value(s) in the table below.

A349068C02
3.094,0.396 3.51,0.688 0.417,0.292 2.865,2.354 3.052,1.323 true 2.708,2.385 3.323,2.583 0.615,0.198 10 false STA2 0.146,0.115 0.458,0.313 0.313,0.198 10 false *a 3.146,0.458 3.552,0.635 0.406,0.177 10 false G126
*a Component with harness connected
(Engine Stop and Start ECU)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
G126-23 (STA2) - Body ground Vehicle driving (Engine speed of 1000 rpm or more and vehicle speed at 20 km/h (12.4 mph) or more) 0 to 1.5 V



Result:
Proceed to
OK
NG



OK

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

NG

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace the harness or connector (STA signal circuit).


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.


d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.4 mph) or more and an engine speed of 1000 rpm or more.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234

Result:
Result Proceed to
DTC P0617 is output A
DTCs are not output B



A

B

END

5.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

Result:
Proceed to
OK
NG



OK

6.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

6.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>2GD-FTV STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

7.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

NG

8.REPLACE IGNITION OR STARTER SWITCH ASSEMBLY
7.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace the harness or connector (STA signal circuit).


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
8.REPLACE IGNITION OR STARTER SWITCH ASSEMBLY
a.

Replace the ignition switch assembly.

Click hereEngine / Hybrid System>2GD-FTV STARTING>IGNITION SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER DTC OUTPUT RECURS
9.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.


c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON.


e.

Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.4 mph) or more and an engine speed of 1000 rpm or more.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Confirm that the DTC is not output again.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END

10.INSPECT CLUTCH START SWITCH
a.

Inspect the clutch start switch.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

11.INSPECT IGNITION SWITCH ASSEMBLY

NG

15.REPLACE CLUTCH START SWITCH ASSEMBLY
11.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>2GD-FTV STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

12.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

NG

13.REPLACE IGNITION SWITCH ASSEMBLY
12.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace the harness or connector (STA signal circuit).


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
13.REPLACE IGNITION SWITCH ASSEMBLY
a.

Replace the ignition switch assembly.

Click hereEngine / Hybrid System>2GD-FTV STARTING>IGNITION SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.CONFIRM WHETHER DTC OUTPUT RECURS
14.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.


c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON.


e.

Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.4 mph) or more and an engine speed of 1000 rpm or more.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Confirm that the DTC is not output again.

Powertrain > Engine > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END

15.REPLACE CLUTCH START SWITCH ASSEMBLY
a.

Replace the clutch start switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.CONFIRM WHETHER DTC OUTPUT RECURS