Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM › from 2016.08
RM3250E _56 Audio / Visual / Telematics _057181 TELEMATICS _0280391 TELEMATICS SYSTEM C

TELEMATICS  TELEMATICS SYSTEM  B1573  Short in Telephone Antenna Circuit  B15CB  Telephone Antenna Disconnected  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the telephone antenna assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1573 Short in Telephone Antenna Circuit Telephone antenna assembly impedance (Ω) is lower than the malfunction threshold for 20 seconds when the ignition switch is ON.
(Short circuit)
·

Telematics transceiver

·

Roof antenna pole sub-assembly

·

No. 1 amplifier antenna assembly

·

No. 2 antenna cord sub-assembly

·

Antenna cord sub-assembly


B15CB Telephone Antenna Disconnected Telephone antenna assembly impedance (Ω) is higher than the malfunction threshold for 20 seconds when the ignition switch is ON.
(Open circuit)
·

Telematics transceiver

·

Roof antenna pole sub-assembly

·

No. 1 amplifier antenna assembly

·

No. 2 antenna cord sub-assembly

·

Antenna cord sub-assembly



WIRING DIAGRAM

E350973E04
0.677,2.417 1.865,2.771 1.188,0.354 10 false No. 1 Amplifier Antenna Assembly 5.521,2.448 7,2.688 1.479,0.24 10 false Telematics Transceiver 4.198,2.417 5.094,2.833 0.896,0.417 10 false Antenna Cord Sub-assembly 2.073,2.438 3.323,2.865 1.25,0.427 10 false No. 2 Antenna Cord Sub-assembly 1.844,1.281 2.177,1.49 0.333,0.208 10 false A 1.823,1.781 2.156,1.99 0.333,0.208 10 false 2a 3.375,1.281 3.708,1.49 0.333,0.208 10 false B 3.344,1.771 3.677,1.979 0.333,0.208 10 false 6a 3.813,1.281 4.146,1.49 0.333,0.208 10 false C 3.792,1.792 4.125,2 0.333,0.208 10 false 1a 5.333,1.073 5.667,1.281 0.333,0.208 10 false 1 5.302,1.781 5.635,1.99 0.333,0.208 10 false 1a 1.854,1.083 2.188,1.292 0.333,0.208 10 false 2 1.844,1.99 2.177,2.198 0.333,0.208 10 false A 3.375,1.969 3.708,2.177 0.333,0.208 10 false B 3.813,1.979 4.146,2.188 0.333,0.208 10 false C 5.344,1.281 5.677,1.49 0.333,0.208 10 false D 5.344,1.979 5.677,2.188 0.333,0.208 10 false D 3.823,1.083 4.156,1.292 0.333,0.208 10 false 1 3.375,1.083 3.708,1.292 0.333,0.208 10 false 6 5.656,1.281 6.052,1.51 0.396,0.229 10 false ANT1 0.052,0.375 1.219,0.76 1.167,0.385 10 false Roof Antenna Pole Sub-assembly

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>REGISTRATION


PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait for 20 seconds.


d.

Turn the GTS on.


e.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK ROOF ANTENNA POLE SUB-ASSEMBLY
2.CHECK ROOF ANTENNA POLE SUB-ASSEMBLY
a.

Check that the roof antenna pole sub-assembly is securely installed.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA POLE>INSTALLATION

OK:

The roof antenna pole sub-assembly is installed properly.



Result:
Proceed to
OK
NG



OK

3.INSPECT NO. 1 AMPLIFIER ANTENNA ASSEMBLY

NG

CHECK AND REPLACE ROOF ANTENNA POLE SUB-ASSEMBLY

3.INSPECT NO. 1 AMPLIFIER ANTENNA ASSEMBLY
a.

Remove the No. 1 amplifier antenna assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL


b.
E350996C01
2.177,1.01 2.594,0.906 true 2.667,0.823 2.979,1.021 0.313,0.198 10 false 2a
*a Component without harness connected
(No. 1 Amplifier Antenna Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 2a Always 4 to 11 kΩ



Result:
Proceed to
OK
NG



OK

4.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE NO. 1 AMPLIFIER ANTENNA ASSEMBLY

4.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.

Disconnect the antenna connector from the No. 1 amplifier antenna assembly.


b.

Disconnect the antenna connector from the antenna cord sub-assembly.


c.
E350997C01
1.479,0.5 1.896,0.792 0.417,0.292 1.469,2.552 1.885,2.844 0.417,0.292 0.979,1.219 1.427,1.458 true 2.698,3.427 3.031,3.354 true 0.167,0.125 0.479,0.323 0.313,0.198 10 false *a 0.177,2.354 0.49,2.552 0.313,0.198 10 false *b 0.792,1.104 1.104,1.302 0.313,0.198 10 false 2a 3.073,3.26 3.385,3.458 0.313,0.198 10 false 6a 1.646,0.573 1.802,0.771 0.156,0.198 10 false A 1.635,2.625 1.792,2.823 0.156,0.198 10 false B
*a Front view of wire harness connector
(to No. 1 Amplifier Antenna Assembly)
*b Front view of wire harness connector
(to Antenna Cord Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 - B-6 Always Below 1 Ω
A-2a - B-6a Always Below 1 Ω
A-2 or B-6 - Body ground Always 10 kΩ or higher
A-2a or B-6a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

5.INSPECT ANTENNA CORD SUB-ASSEMBLY
a.

Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.


b.

Disconnect the antenna connector from the telematics transceiver.


c.
E350998C01
1.552,0.531 1.969,0.844 0.417,0.313 1.552,2.781 1.969,3.094 0.417,0.313 1.906,3.917 2.177,4.198 true 2.677,1.531 3.021,1.385 true 1.333,3.635 1.719,3.833 true 0.229,0.26 0.542,0.458 0.313,0.198 10 false *a 0.25,2.802 0.563,3 0.313,0.198 10 false *b 2.24,4.167 2.552,4.365 0.313,0.198 10 false 1a 3.073,1.302 3.385,1.5 0.313,0.198 10 false 1a 1.719,0.604 2.031,0.802 0.313,0.198 10 false C 1.719,2.865 2.031,3.063 0.313,0.198 10 false D 0.948,3.542 1.375,3.74 0.427,0.198 10 false ANT1
*a Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Telematics Transceiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C-1 - D-1 (ANT1) Always Below 1 Ω
C-1a - D-1a Always Below 1 Ω
C-1 or D-1 (ANT1) - Body ground Always 10 kΩ or higher
C-1a or D-1a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.REPLACE TELEMATICS TRANSCEIVER

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY

6.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT