This DTC is stored when a malfunction occurs in the speakers.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15C3 | Speaker Output Short | A short is detected in the speaker output circuit | ·
Harness or connector ·
Speakers ·
Radio and display receiver assembly ·
Telematics transceiver* |
*: w/ Telematics Transceiver
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
Clear the DTCs.
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 2 Speakers, for 4 Speakers [Single Cab]) | B |
| NG (for 4 Speakers [Double Cab, Smart Cab]) | C |
| NG (for 6 Speakers) | D |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
D
*1: for LH Side
*2: for RH Side
Disconnect the G40 radio and display receiver assembly connector.
Disconnect the K4*1 and/or J4*2 front No. 1 speaker assembly connector.
for 4 Speakers (Single Cab):
Disconnect the K7*1 and/or J7*2 front No. 2 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G40-2 (FL+) - K4-1 | Always | Below 1 Ω |
| G40-6 (FL-) - K4-2 | Always | Below 1 Ω |
| G40-2 (FL+) or K4-1 - Body ground | Always | 10 kΩ or higher |
| G40-6 (FL-) or K4-2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G40-2 (FL+) - K7-4 (TWL+) | Always | Below 1 Ω |
| G40-6 (FL-) - K7-2 (TWL-) | Always | Below 1 Ω |
| K7-3 (+) - K4-1 | Always | Below 1 Ω |
| K7-1 (-) - K4-2 | Always | Below 1 Ω |
| G40-2 (FL+) or K7-4 (TWL+) - Body ground | Always | 10 kΩ or higher |
| G40-6 (FL-) or K7-2 (TWL-) - Body ground | Always | 10 kΩ or higher |
| K7-3 (+) or K4-1 - Body ground | Always | 10 kΩ or higher |
| K7-1 (-) or K4-2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G40-1 (FR+) - J4-1 | Always | Below 1 Ω |
| G40-5 (FR-) - J4-2 | Always | Below 1 Ω |
| G40-1 (FR+) or J4-1 - Body ground | Always | 10 kΩ or higher |
| G40-5 (FR-) or J4-2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G40-1 (FR+) - J7-4 (TWR+) | Always | Below 1 Ω |
| G40-5 (FR-) - J7-2 (TWR-) | Always | Below 1 Ω |
| J7-3 (+) - J4-1 | Always | Below 1 Ω |
| J7-1 (-) - J4-2 | Always | Below 1 Ω |
| G40-1 (FR+) or J7-4 (TWR+) - Body ground | Always | 10 kΩ or higher |
| G40-5 (FR-) or J7-2 (TWR-) - Body ground | Always | 10 kΩ or higher |
| J7-3 (+) or J4-1 - Body ground | Always | 10 kΩ or higher |
| J7-1 (-) or J4-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Inspect the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Result | Proceed to |
|---|---|
| OK (for 2 Speakers) | A |
| OK (for 4 Speakers [Single Cab]) | B |
| NG | C |
A
B
C
Replace the front No. 2 speaker assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Clear the DTCs.
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for LH Side
*2: for RH Side
*3: w/o Telematics Transceiver
*4: w/ Telematics Transceiver
Disconnect the G40 and G41 radio and display receiver assembly connectors.
Disconnect the K4*1 and/or J4*2 front No. 1 speaker assembly connector.
Disconnect the M2*1 and/or L2*2 rear speaker assembly connector.
Disconnect the G130 telematics transceiver connector.*4
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G40-2 (FL+) - K4-1 | Always | Below 1 Ω |
| G40-6 (FL-) - K4-2 | Always | Below 1 Ω |
| G41-2 (RL+) - M2-1 | Always | Below 1 Ω |
| G41-6 (RL-) - M2-2 | Always | Below 1 Ω |
| G40-2 (FL+) or K4-1 - Body ground | Always | 10 kΩ or higher |
| G40-6 (FL-) or K4-2 - Body ground | Always | 10 kΩ or higher |
| G41-2 (RL+) or M2-1 - Body ground | Always | 10 kΩ or higher |
| G41-6 (RL-) or M2-2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G40-1 (FR+) - J4-1*3 | Always | Below 1 Ω |
| G40-1 (FR+) - G130-2 (SPI+)*4 | Always | Below 1 Ω |
| G40-5 (FR-) - J4-2*3 | Always | Below 1 Ω |
| G40-5 (FR-) - G130-3 (SPI-)*4 | Always | Below 1 Ω |
| G130-5 (SPO+) - J4-1*4 | Always | Below 1 Ω |
| G130-6 (SPO-) - J4-2*4 | Always | Below 1 Ω |
| G41-1 (RR+) - L2-1 | Always | Below 1 Ω |
| G41-3 (RR-) - L2-2 | Always | Below 1 Ω |
| G40-1 (FR+) or J4-1 - Body ground*3 | Always | 10 kΩ or higher |
| G40-1 (FR+) or G130-2 (SPI+) - Body ground*4 | Always | 10 kΩ or higher |
| G40-5 (FR-) or J4-2 - Body ground*3 | Always | 10 kΩ or higher |
| G40-5 (FR-) or G130-3 (SPI-) - Body ground*4 | Always | 10 kΩ or higher |
| G130-5 (SPO+) or J4-1 - Body ground*4 | Always | 10 kΩ or higher |
| G130-6 (SPO-) or J4-2 - Body ground*4 | Always | 10 kΩ or higher |
| G41-1 (RR+) or L2-1 - Body ground | Always | 10 kΩ or higher |
| G41-3 (RR-) or L2-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Inspect the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speaker assembly.
for Smart Cab: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Smart Cab)>REMOVAL
for Double Cab: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Double Cab)>REMOVAL
Inspect the rear speaker assembly.
for Smart Cab: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Smart Cab)>INSPECTION
for Double Cab: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Double Cab)>INSPECTION
| Result | Proceed to |
|---|---|
| OK (w/ Telematics Transceiver) | A |
| OK (w/o Telematics Transceiver) | B |
| NG | C |
A
B
C
for Smart Cab: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Smart Cab)>REMOVAL
for Double Cab: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Double Cab)>REMOVAL
*1: for LH Side
*2: for RH Side
*3: w/o Telematics Transceiver
*4: w/ Telematics Transceiver
Disconnect the G40 and G41 radio and display receiver assembly connectors.
Disconnect the K4*1 and/or J4*2 front No. 1 speaker assembly connector.
Disconnect the K7*1 and/or J7*2 front No. 2 speaker assembly connector.
Disconnect the M2*1 and/or L2*2 rear speaker assembly connector.
Disconnect the G130 telematics transceiver connector.*4
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G40-2 (FL+) - K7-4 (TWL+) | Always | Below 1 Ω |
| G40-6 (FL-) - K7-2 (TWL-) | Always | Below 1 Ω |
| K7-3 (+) - K4-1 | Always | Below 1 Ω |
| K7-1 (-) - K4-2 | Always | Below 1 Ω |
| G41-2 (RL+) - M2-1 | Always | Below 1 Ω |
| G41-6 (RL-) - M2-2 | Always | Below 1 Ω |
| G40-2 (FL+) or K7-4 (TWL+) - Body ground | Always | 10 kΩ or higher |
| G40-6 (FL-) or K7-2 (TWL-) - Body ground | Always | 10 kΩ or higher |
| K7-3 (+) or K4-1 - Body ground | Always | 10 kΩ or higher |
| K7-1 (-) or K4-2 - Body ground | Always | 10 kΩ or higher |
| G41-2 (RL+) or M2-1 - Body ground | Always | 10 kΩ or higher |
| G41-6 (RL-) or M2-2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G40-1 (FR+) - J7-4 (TWR+)*3 | Always | Below 1 Ω |
| G40-1 (FR+) - G130-2 (SPI+)*4 | Always | Below 1 Ω |
| G40-5 (FR-) - J7-2 (TWR-)*3 | Always | Below 1 Ω |
| G40-5 (FR-) - G130-3 (SPI-)*4 | Always | Below 1 Ω |
| G130-5 (SPO+) - J7-4 (TWR+)*4 | Always | Below 1 Ω |
| G130-6 (SPO-) - J7-2 (TWR-)*4 | Always | Below 1 Ω |
| J7-3 (+) - J4-1 | Always | Below 1 Ω |
| J7-1 (-) - J4-2 | Always | Below 1 Ω |
| G41-1 (RR+) - L2-1 | Always | Below 1 Ω |
| G41-3 (RR-) - L2-2 | Always | Below 1 Ω |
| G40-1 (FR+) or J7-4 (TWR+) - Body ground*3 | Always | 10 kΩ or higher |
| G40-1 (FR+) or G130-2 (SPI+) - Body ground*4 | Always | 10 kΩ or higher |
| G40-5 (FR-) or J7-2 (TWR-) - Body ground*3 | Always | 10 kΩ or higher |
| G40-5 (FR-) or G130-3 (SPI-) - Body ground*4 | Always | 10 kΩ or higher |
| G130-5 (SPO+) or J7-4 (TWR+) - Body ground*4 | Always | 10 kΩ or higher |
| G130-6 (SPO-) or J7-2 (TWR-) - Body ground*4 | Always | 10 kΩ or higher |
| J7-3 (+) or J4-1 - Body ground | Always | 10 kΩ or higher |
| J7-1 (-) or J4-2 - Body ground | Always | 10 kΩ or higher |
| G41-1 (RR+) or L2-1 - Body ground | Always | 10 kΩ or higher |
| G41-3 (RR-) or L2-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Inspect the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speaker assembly.
for Smart Cab:
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Smart Cab)>REMOVAL
for Double Cab:
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Double Cab)>REMOVAL
Inspect the rear speaker assembly.
for Smart Cab:
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Smart Cab)>INSPECTION
for Double Cab:
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Double Cab)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Smart Cab:
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Smart Cab)>REMOVAL
for Double Cab:
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Double Cab)>REMOVAL
Replace the front No. 2 speaker assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Clear the DTCs.
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/ Telematics Transceiver) | B |
| NG (w/o Telematics Transceiver) | C |
A
B
C
Replace the telematics transceiver with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
Clear the DTCs.
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG