If there is a short in a speaker circuit, the radio and display receiver assembly detects it and stops output to the speakers.
As a result, sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly, telematics transceiver* or speakers.
*: w/ Telematics Transceiver
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
Check speaker type.
| Result | Proceed to |
|---|---|
| for 2 Speakers, for 4 Speakers (Single Cab) | A |
| for 4 Speakers (Double Cab, Smart Cab) | B |
| for 6 Speakers | C |
A
B
C
*1: for LH Side
*2: for RH Side
Disconnect the G40 radio and display receiver assembly connector.
Disconnect the K4*1 and/or J4*2 front No. 1 speaker assembly connector.
for 4 Speakers (Single Cab):
Disconnect the K7*1 and/or J7*2 front No. 2 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G40-2 (FL+) - K4-1 | Always | Below 1 Ω |
| G40-6 (FL-) - K4-2 | Always | Below 1 Ω |
| G40-2 (FL+) or K4-1 - Body ground | Always | 10 kΩ or higher |
| G40-6 (FL-) or K4-2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G40-2 (FL+) - K7-4 (TWL+) | Always | Below 1 Ω |
| G40-6 (FL-) - K7-2 (TWL-) | Always | Below 1 Ω |
| K7-3 (+) - K4-1 | Always | Below 1 Ω |
| K7-1 (-) - K4-2 | Always | Below 1 Ω |
| G40-2 (FL+) or K7-4 (TWL+) - Body ground | Always | 10 kΩ or higher |
| G40-6 (FL-) or K7-2 (TWL-) - Body ground | Always | 10 kΩ or higher |
| K7-3 (+) or K4-1 - Body ground | Always | 10 kΩ or higher |
| K7-1 (-) or K4-2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G40-1 (FR+) - J4-1 | Always | Below 1 Ω |
| G40-5 (FR-) - J4-2 | Always | Below 1 Ω |
| G40-1 (FR+) or J4-1 - Body ground | Always | 10 kΩ or higher |
| G40-5 (FR-) or J4-2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G40-1 (FR+) - J7-4 (TWR+) | Always | Below 1 Ω |
| G40-5 (FR-) - J7-2 (TWR-) | Always | Below 1 Ω |
| J7-3 (+) - J4-1 | Always | Below 1 Ω |
| J7-1 (-) - J4-2 | Always | Below 1 Ω |
| G40-1 (FR+) or J7-4 (TWR+) - Body ground | Always | 10 kΩ or higher |
| G40-5 (FR-) or J7-2 (TWR-) - Body ground | Always | 10 kΩ or higher |
| J7-3 (+) or J4-1 - Body ground | Always | 10 kΩ or higher |
| J7-1 (-) or J4-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Inspect the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Result | Proceed to |
|---|---|
| OK (for 2 Speakers) | A |
| OK (for 4 Speakers [Single Cab]) | B |
| NG | C |
A
B
C
Replace the front No. 2 speaker assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Check that sound is emitted from the speaker normally.
Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
Perform the above inspection on both the LH and RH sides.
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for LH Side
*2: for RH Side
*3: w/o Telematics Transceiver
*4: w/ Telematics Transceiver
Disconnect the G40 and G41 radio and display receiver assembly connectors.
Disconnect the K4*1 and/or J4*2 front No. 1 speaker assembly connector.
Disconnect the M2*1 and/or L2*2 rear speaker assembly connector.
Disconnect the G130 telematics transceiver connector.*4
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G40-2 (FL+) - K4-1 | Always | Below 1 Ω |
| G40-6 (FL-) - K4-2 | Always | Below 1 Ω |
| G41-2 (RL+) - M2-1 | Always | Below 1 Ω |
| G41-6 (RL-) - M2-2 | Always | Below 1 Ω |
| G40-2 (FL+) or K4-1 - Body ground | Always | 10 kΩ or higher |
| G40-6 (FL-) or K4-2 - Body ground | Always | 10 kΩ or higher |
| G41-2 (RL+) or M2-1 - Body ground | Always | 10 kΩ or higher |
| G41-6 (RL-) or M2-2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G40-1 (FR+) - J4-1*3 | Always | Below 1 Ω |
| G40-1 (FR+) - G130-2 (SPI+)*4 | Always | Below 1 Ω |
| G40-5 (FR-) - J4-2*3 | Always | Below 1 Ω |
| G40-5 (FR-) - G130-3 (SPI-)*4 | Always | Below 1 Ω |
| G130-5 (SPO+) - J4-1*4 | Always | Below 1 Ω |
| G130-6 (SPO-) - J4-2*4 | Always | Below 1 Ω |
| G41-1 (RR+) - L2-1 | Always | Below 1 Ω |
| G41-3 (RR-) - L2-2 | Always | Below 1 Ω |
| G40-1 (FR+) or J4-1 - Body ground*3 | Always | 10 kΩ or higher |
| G40-1 (FR+) or G130-2 (SPI+) - Body ground*4 | Always | 10 kΩ or higher |
| G40-5 (FR-) or J4-2 - Body ground*3 | Always | 10 kΩ or higher |
| G40-5 (FR-) or G130-3 (SPI-) - Body ground*4 | Always | 10 kΩ or higher |
| G130-5 (SPO+) or J4-1 - Body ground*4 | Always | 10 kΩ or higher |
| G130-6 (SPO-) or J4-2 - Body ground*4 | Always | 10 kΩ or higher |
| G41-1 (RR+) or L2-1 - Body ground | Always | 10 kΩ or higher |
| G41-3 (RR-) or L2-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Inspect the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speaker assembly.
for Smart Cab: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Smart Cab)>REMOVAL
for Double Cab: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Double Cab)>REMOVAL
Inspect the rear speaker assembly.
for Smart Cab: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Smart Cab)>INSPECTION
for Double Cab: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Double Cab)>INSPECTION
| Result | Proceed to |
|---|---|
| OK (w/ Telematics Transceiver) | A |
| OK (w/o Telematics Transceiver) | B |
| NG | C |
A
B
C
for Smart Cab: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Smart Cab)>REMOVAL
for Double Cab: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Double Cab)>REMOVAL
*1: for LH Side
*2: for RH Side
*3: w/o Telematics Transceiver
*4: w/ Telematics Transceiver
Disconnect the G40 and G41 radio and display receiver assembly connectors.
Disconnect the K4*1 and/or J4*2 front No. 1 speaker assembly connector.
Disconnect the K7*1 and/or J7*2 front No. 2 speaker assembly connector.
Disconnect the M2*1 and/or L2*2 rear speaker assembly connector.
Disconnect the G130 telematics transceiver connector.*4
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G40-2 (FL+) - K7-4 (TWL+) | Always | Below 1 Ω |
| G40-6 (FL-) - K7-2 (TWL-) | Always | Below 1 Ω |
| K7-3 (+) - K4-1 | Always | Below 1 Ω |
| K7-1 (-) - K4-2 | Always | Below 1 Ω |
| G41-2 (RL+) - M2-1 | Always | Below 1 Ω |
| G41-6 (RL-) - M2-2 | Always | Below 1 Ω |
| G40-2 (FL+) or K7-4 (TWL+) - Body ground | Always | 10 kΩ or higher |
| G40-6 (FL-) or K7-2 (TWL-) - Body ground | Always | 10 kΩ or higher |
| K7-3 (+) or K4-1 - Body ground | Always | 10 kΩ or higher |
| K7-1 (-) or K4-2 - Body ground | Always | 10 kΩ or higher |
| G41-2 (RL+) or M2-1 - Body ground | Always | 10 kΩ or higher |
| G41-6 (RL-) or M2-2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G40-1 (FR+) - J7-4 (TWR+)*3 | Always | Below 1 Ω |
| G40-1 (FR+) - G130-2 (SPI+)*4 | Always | Below 1 Ω |
| G40-5 (FR-) - J7-2 (TWR-)*3 | Always | Below 1 Ω |
| G40-5 (FR-) - G130-3 (SPI-)*4 | Always | Below 1 Ω |
| G130-5 (SPO+) - J7-4 (TWR+)*4 | Always | Below 1 Ω |
| G130-6 (SPO-) - J7-2 (TWR-)*4 | Always | Below 1 Ω |
| J7-3 (+) - J4-1 | Always | Below 1 Ω |
| J7-1 (-) - J4-2 | Always | Below 1 Ω |
| G41-1 (RR+) - L2-1 | Always | Below 1 Ω |
| G41-3 (RR-) - L2-2 | Always | Below 1 Ω |
| G40-1 (FR+) or J7-4 (TWR+) - Body ground*3 | Always | 10 kΩ or higher |
| G40-1 (FR+) or G130-2 (SPI+) - Body ground*4 | Always | 10 kΩ or higher |
| G40-5 (FR-) or J7-2 (TWR-) - Body ground*3 | Always | 10 kΩ or higher |
| G40-5 (FR-) or G130-3 (SPI-) - Body ground*4 | Always | 10 kΩ or higher |
| G130-5 (SPO+) or J7-4 (TWR+) - Body ground*4 | Always | 10 kΩ or higher |
| G130-6 (SPO-) or J7-2 (TWR-) - Body ground*4 | Always | 10 kΩ or higher |
| J7-3 (+) or J4-1 - Body ground | Always | 10 kΩ or higher |
| J7-1 (-) or J4-2 - Body ground | Always | 10 kΩ or higher |
| G41-1 (RR+) or L2-1 - Body ground | Always | 10 kΩ or higher |
| G41-3 (RR-) or L2-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Inspect the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speaker assembly.
for Smart Cab:
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Smart Cab)>REMOVAL
for Double Cab:
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Double Cab)>REMOVAL
Inspect the rear speaker assembly.
for Smart Cab:
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Smart Cab)>INSPECTION
for Double Cab:
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Double Cab)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Smart Cab:
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Smart Cab)>REMOVAL
for Double Cab:
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Double Cab)>REMOVAL
Replace the front No. 2 speaker assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Check the malfunction disappears.
Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
Perform the above inspection on both the LH and RH sides.
Malfunction disappears.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/ Telematics Transceiver) | B |
| NG (w/o Telematics Transceiver) | C |
A
B
C
Replace the telematics transceiver with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
Check the malfunction disappears.
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG