Home › Engine / Hybrid System › 2GD-FTV ENGINE CONTROL › ECD SYSTEM(w/o EGR Cooler) › from 2016.08
RM3250E _51 Engine / Hybrid System _038005 2GD-FTV ENGINE CONTROL _0278511 ECD SYSTEM(w/o EGR Cooler) J

2GD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR Cooler)  Starter Signal Circuit  


DESCRIPTION

While the engine is being cranked, the starter signal is also sent to terminal STA of the ECM. The starter signal mainly performs engine control when the engine is started.

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:

This procedure is based on the premise that the engine can crank normally. If the engine cannot crank normally, proceed to the problem symptoms table.

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>PROBLEM SYMPTOMS TABLE


PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

OK:
Ignition Switch Position Starter Signal
ON OFF
START ON



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT ST NO. 1 RELAY (POWER SOURCE)
2.INSPECT ST NO. 1 RELAY (POWER SOURCE)
a.
A349008C01
2.135,0.281 2.479,0.5 0.344,0.219 10 false *1 0.865,1.896 1.208,2.115 0.344,0.219 10 false *2
*1 Engine Room Relay Block and Junction Block
*2 ST NO. 1 Relay


Remove the ST NO. 1 relay from the engine room relay block and junction block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
ST NO. 1 relay terminal 2 - Body ground Engine cranking 11 to 14 V


HINT:

The engine does not crank because the relay is not installed.



Result:
Proceed to
OK
NG



OK

3.INSPECT ST NO. 1 RELAY

NG

5.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH - ST NO. 1 RELAY)
3.INSPECT ST NO. 1 RELAY

Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK - BODY GROUND)

NG

REPLACE ST NO. 1 RELAY

4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK - BODY GROUND)
a.

Remove the ST NO. 1 relay from the engine room relay block and Junction block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST NO. 1 relay terminal 1 - Body ground Always Below 1 Ω



Result:
Result
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - CLUTCH START SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST NO. 1 RELAY - BODY GROUND)

5.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH - ST NO. 1 RELAY)
a.

Remove the ST NO. 1 relay from the engine room relay block and junction block.


b.

Disconnect the clutch start switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B2-1 - ST NO. 1 relay terminal 2 Always Below 1 Ω
G49-22 (STA) - ST NO. 1 relay terminal 2 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.INSPECT CLUTCH START SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT CLUTCH START SWITCH
a.

Inspect the clutch start switch.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Result
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - CLUTCH START SWITCH - ECM)

NG

REPLACE CLUTCH START SWITCH

7.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - CLUTCH START SWITCH - ECM)
a.

Disconnect the ignition switch assembly connector.


b.

Disconnect the clutch start switch connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G133-2 (ST2) - B2-2 Always Below 1 Ω
G133-2 (ST2) - G49-11 (NSW) Always Below 1 Ω
G133-2 (ST2) or B2-2 or G49-11 (NSW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>2GD-FTV STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY)

NG

REPLACE IGNITION SWITCH ASSEMBLY