Home › Drivetrain › AXLE AND DIFFERENTIAL › STEERING KNUCKLE(for 4WD and Pre-Runner) › 2015.06–2015.11
RM33J0E _52 Drivetrain _038472 AXLE AND DIFFERENTIAL _0187678 STEERING KNUCKLE(for 4WD and Pre-Runner) A

AXLE AND DIFFERENTIAL  STEERING KNUCKLE(for 4WD and Pre-Runner)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the steering knuckle removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced:
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Front wheel alignment adjustment
·

Clearing zero point calibration data

·

Yaw rate and acceleration sensor zero point calibration


·

DTCs are output

·

ABS warning light illumination

·

Slip indicator light illumination

·

VSC disable or malfunctioning


(Click here)


HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 89543 2.DISCONNECT FRONT SPEED SENSOR LH

a.
C322643

Detach the clamp.


b.

Remove the bolt and harness clamp.


c.
C322645

Detach the clamp.


d.

Remove the bolt and front speed sensor LH from the steering knuckle LH.

NOTICE:

Keep the sensor tip and sensor installation hole free from foreign matter.



e.

Remove the bolt and skid control sensor clamp from the steering knuckle LH.


Hide 47750 3.REMOVE FRONT DISC BRAKE CYLINDER ASSEMBLY LH

Hide 43514C 5.REMOVE FRONT AXLE HUB GREASE CAP LH (for 4WD)

Hide 43502H 6.REMOVE FRONT AXLE SHAFT NUT LH (for 4WD)

Hide 48810 7.DISCONNECT FRONT STABILIZER LINK ASSEMBLY LH

C322819

a.

Remove the nut and disconnect the front stabilizer link assembly LH from the steering knuckle LH.

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud in place.



Hide 8.DISCONNECT TIE ROD END SUB-ASSEMBLY LH

Hide 48069 9.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM ASSEMBLY LH

C322841

a.

Remove the 2 bolts, and disconnect the front lower No. 1 suspension arm assembly LH from the steering knuckle.


Hide 48630 10.DISCONNECT FRONT UPPER SUSPENSION ARM ASSEMBLY LH

a.

Remove the clip and nut.


b.
C335923C01
2.052,1.333 2.469,1.333 true 2.542,1.25 3,1.448 0.458,0.198 10 true SST 3.021,1.802 3.333,2 0.313,0.198 10 true *a 0.188,1.583 0.5,1.781 0.313,0.198 10 true *b
*a Turn
*b Hold


Using SST, disconnect the front upper suspension arm assembly LH from the steering knuckle LH.

SST
09628-62011  


Hide 43502K 11.REMOVE FRONT AXLE HUB DUST SEAL (for 4WD)

C325053

a.

Using a screwdriver and hammer, tap out the front axle hub dust seal.


Hide 43442B 12.REMOVE KNUCKLE GREASE RETAINER CAP LH (for Pre-Runner)

C325054

a.

Using a screwdriver and hammer, remove the knuckle grease retainer cap LH.


Hide 43212 13.REMOVE STEERING KNUCKLE LH

C324912

a.

Remove the 4 bolts, dust cover and front axle hub sub-assembly LH from the steering knuckle LH.


b.

Remove the O-ring from the front axle hub sub-assembly LH.