In some cases, wireless door lock control functions are normal but the hazard warning light answer-back function does not operate. In such cases, hazard warning light signal outputs from the body ECU may be malfunctioning.
If the body ECU has been replaced, it is necessary to initialize the body ECU.*1
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
As the door control battery is installed between the vehicle battery and body ECU, first perform the inspections to confirm that there are no malfunctions in the power source circuit for the body ECU before performing this troubleshooting procedure.*2
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION
*1: w/ Automatic Light Control System
*2: w/ Door Control Battery
Check that the hazard warning light blinks when the hazard warning signal switch is pressed.
Hazard warning light signal is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G11 combination meter assembly connector.
Disconnect the G27 body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G11-2 (HAZ) - G27-6 (HAZ) | Always | Below 1 Ω |
| G11-2 (HAZ) or G27-6 (HAZ) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*: for Double Cab
for Front Side:
Remove the front door lock assembly.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL
Inspect the front door lock assembly.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION
for Rear Side*:
Remove the rear door lock assembly.
Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK(for Double Cab)>REMOVAL
Inspect the rear door lock assembly.
Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK(for Double Cab)>INSPECTION
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for Front Side) | B |
| NG (for Rear Side) | C |
A
B
C
*1: for LHD
*2: for RHD
*3: for Double Cab
for Driver Side:
Disconnect the K1*1 or J1*2 front door lock assembly LH*1 or RH*2 connector.
Disconnect the G27 body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K1-7 (LSSR) - G27-15 (LSWD) | Always | Below 1 Ω |
| K1-8 (E) - Body ground | Always | Below 1 Ω |
| K1-7 (LSSR) or G27-15 (LSWD) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J1-7 (LSSR) - G27-15 (LSWD) | Always | Below 1 Ω |
| J1-8 (E) - Body ground | Always | Below 1 Ω |
| J1-7 (LSSR) or G27-15 (LSWD) - Body ground | Always | 10 kΩ or higher |
except Driver Side:
Disconnect the J1*1 or K1*2 front door lock assembly RH*1 or LH*2 connector.
Disconnect the L1 rear door lock assembly RH connector*3.
Disconnect the M1 rear door lock assembly LH connector*3.
Disconnect the G27 body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J1-8 (LSSR) - G27-2 (LSWP) | Always | Below 1 Ω |
| J1-7 (E) - Body ground | Always | Below 1 Ω |
| J1-8 (LSSR) or G27-2 (LSWP) - Body ground | Always | 10 kΩ or higher |
| L1-6 (LSSR) - G27-2 (LSWP)*3 | Always | Below 1 Ω |
| L1-9 (E) - Body ground*3 | Always | Below 1 Ω |
| L1-6 (LSSR) or G27-2 (LSWP) - Body ground*3 | Always | 10 kΩ or higher |
| M1-6 (LSSR) - G27-2 (LSWP)*3 | Always | Below 1 Ω |
| M1-9 (E) - Body ground*3 | Always | Below 1 Ω |
| M1-6 (LSSR) or G27-2 (LSWP) - Body ground*3 | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K1-8 (LSSR) - G27-2 (LSWP) | Always | Below 1 Ω |
| K1-7 (E) - Body ground | Always | Below 1 Ω |
| K1-8 (LSSR) or G27-2 (LSWP) - Body ground | Always | 10 kΩ or higher |
| L1-6 (LSSR) - G27-2 (LSWP)*3 | Always | Below 1 Ω |
| L1-9 (E) - Body ground*3 | Always | Below 1 Ω |
| L1-6 (LSSR) or G27-2 (LSWP) - Body ground*3 | Always | 10 kΩ or higher |
| M1-6 (LSSR) - G27-2 (LSWP)*3 | Always | Below 1 Ω |
| M1-9 (E) - Body ground*3 | Always | Below 1 Ω |
| M1-6 (LSSR) or G27-2 (LSWP) - Body ground*3 | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD:Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD:Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
NG