Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type)
RM33J0E _56 Audio / Visual / Telematics _038485 AUDIO / VIDEO _0191433 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Steering Pad Switch Circuit  


DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the radio and display receiver assembly.

If there is an open in the circuit, the audio and visual system cannot be operated using the steering pad switch assembly.

If there is a short in the circuit, the same condition as when a switch is continuously depressed occurs.

Therefore, the radio and display receiver assembly cannot be operated using the steering pad switch assembly, and the radio and display receiver assembly itself will not function.

WIRING DIAGRAM

E324859E03
1.042,3.604 5.323,3.802 4.281,0.198 10 false Steering Pad Switch Assembly 3.677,3.552 5.302,3.938 1.625,0.385 10 false Spiral with Sensor Cable Sub-assembly*1 5.844,3.552 7.063,3.979 1.219,0.427 10 false G37 5.844,3.719 7.063,4.146 1.219,0.427 10 false Radio and Display Receiver Assembly 6.125,3.063 6.833,3.365 0.708,0.302 10 false SW2 6.115,1.958 6.823,2.26 0.708,0.302 10 false SWG 6.115,0.844 6.823,1.146 0.708,0.302 10 false SW1 5.865,0.771 6.573,1.073 0.708,0.302 10 false 21 5.865,1.875 6.573,2.177 0.708,0.302 10 false 23 5.865,2.99 6.573,3.292 0.708,0.302 10 false 22 4.792,3.083 5.5,3.385 0.708,0.302 10 false G4 4.792,1.969 5.5,2.271 0.708,0.302 10 false G4 4.781,0.875 5.49,1.177 0.708,0.302 10 false G4 3.813,0.865 4.521,1.167 0.708,0.302 10 false z2 3.813,1.969 4.521,2.271 0.708,0.302 10 false z2 3.802,3.083 4.51,3.385 0.708,0.302 10 false z2 3.813,2.885 4.521,3.188 0.708,0.302 10 false 10 3.844,1.792 4.552,2.094 0.708,0.302 10 false 8 3.802,0.667 4.51,0.969 0.708,0.302 10 false 11 4.24,0.771 4.948,1.073 0.708,0.302 10 false AU1 4.24,1.885 4.948,2.188 0.708,0.302 10 false EAU 4.25,2.99 4.958,3.292 0.708,0.302 10 false AU2 4.833,1.781 5.542,2.083 0.708,0.302 10 false 3 4.833,2.896 5.542,3.198 0.708,0.302 10 false 5 4.823,0.667 5.531,0.969 0.708,0.302 10 false 6 0.417,2.5 1.125,2.802 0.708,0.302 10 false Voice 0.99,2.156 1.698,2.458 0.708,0.302 10 false Off Hook 1.688,2.146 2.396,2.448 0.708,0.302 10 false On Hook 2.594,2.333 3.302,2.635 0.708,0.302 10 false Mode 2.531,1.365 3.24,1.667 0.708,0.302 10 false Seek+ 1.854,1.365 2.563,1.667 0.708,0.302 10 false Seek- 1,1.083 1.708,1.385 0.708,0.302 10 false Volume+ 0.333,1.073 1.042,1.375 0.708,0.302 10 false Volume- 0.208,4.094 4.49,4.292 4.281,0.198 10 false *1: w/ VSC 0.208,4.448 4.49,4.646 4.281,0.198 10 false *2: w/o VSC 3.698,4.167 5.635,4.396 1.938,0.229 10 false Spiral Cable Sub-assembly*2

CAUTION / NOTICE / HINT

NOTICE:

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

for Type A: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION

for Type B: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


PROCEDURE

1.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK VEHICLE CONDITION

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

2.CHECK VEHICLE CONDITION
a.

Check the vehicle condition.


Result:
Result Proceed to
w/ VSC A
w/o VSC B



A

3.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

B

5.INSPECT SPIRAL CABLE SUB-ASSEMBLY
3.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY
a.

Remove the spiral with sensor cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral with sensor cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY AND BODY GROUND)

NG

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY AND BODY GROUND)
a.

Disconnect the G37 radio and display receiver assembly connector.


b.

Disconnect the G4 spiral with sensor cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G37-21 (SW1) - G4-6 (AU1) Always Below 1 Ω
G37-22 (SW2) - G4-5 (AU2) Always Below 1 Ω
G37-23 (SWG) - Body ground Always Below 1 Ω
G4-3 (EAU) - Body ground Always Below 1 Ω
G37-21 (SW1) or G4-6 (AU1) - Body ground Always 10 kΩ or higher
G37-22 (SW2) or G4-5 (AU2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY AND BODY GROUND)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY AND BODY GROUND)
a.

Disconnect the G37 radio and display receiver assembly connector.


b.

Disconnect the G4 spiral cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G37-21 (SW1) - G4-6 (AU1) Always Below 1 Ω
G37-22 (SW2) - G4-5 (AU2) Always Below 1 Ω
G37-23 (SWG) - Body ground Always Below 1 Ω
G4-3 (EAU) - Body ground Always Below 1 Ω
G37-21 (SW1) or G4-6 (AU1) - Body ground Always 10 kΩ or higher
G37-22 (SW2) or G4-5 (AU2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR