Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
w/ Airbag System:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
for Type A: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION
for Type B: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION
1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
2.DRAIN ENGINE COOLANT
for 1GD-FTV:
Click hereEngine / Hybrid System>1GD-FTV COOLING>COOLANT>REPLACEMENT
for 2GD-FTV:
Click hereEngine / Hybrid System>2GD-FTV COOLING>COOLANT>REPLACEMENT
for 1KD-FTV:
Click hereEngine / Hybrid System>1KD-FTV COOLING>COOLANT>REPLACEMENT
for 2KD-FTV:
Click hereEngine / Hybrid System>2KD-FTV COOLING>COOLANT>REPLACEMENT
for 2TR-FE:
Click hereEngine / Hybrid System>2TR-FE COOLING>COOLANT>REPLACEMENT
88710E
3.DISCONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY (for 1GD-FTV, 2GD-FTV)
Remove the bolt and disconnect the air conditioner tube and accessory assembly.
Remove the 2 O-rings from the air conditioner tube and accessory assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.
88707
4.DISCONNECT SUCTION PIPE SUB-ASSEMBLY (except 1GD-FTV, 2GD-FTV)
|
Remove in this Direction |
Remove the bolt and rotate the hook connector as shown in the illustration.
Disconnect the suction pipe sub-assembly.
Remove the O-ring from the suction pipe sub-assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.
88710E
5.DISCONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY (except 1GD-FTV, 2GD-FTV)
Disconnect the air conditioner tube and accessory assembly.
Remove the O-ring from the air conditioner tube and accessory assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.
6.DISCONNECT HEATER WATER OUTLET HOSE
Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water outlet hose.
Do not apply excessive force to the water hose and heater water outlet hose.
Prepare a drain pan or cloth in case the coolant leaks.
7.DISCONNECT HEATER WATER INLET HOSE
Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water inlet hose.
Do not apply excessive force to the water hose and heater water inlet hose.
Prepare a drain pan or cloth in case the coolant leaks.
87128
8.REMOVE HEATER GROMMET
Detach the claw and remove the heater grommet.
9.REMOVE FRONT SEAT ASSEMBLY LH
for Manual Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>REMOVAL
for Power Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>REMOVAL
for Bench Seat Type:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>REMOVAL
10.REMOVE FRONT SEAT ASSEMBLY RH
Use the same procedure described for the LH side.
55303B
11.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
58810J
12.REMOVE CONSOLE BOX ASSEMBLY (w/ Console Box Lid)
58811A
13.REMOVE FRONT CONSOLE BOX (w/o Console Box Lid)
87211
14.REMOVE NO. 1 AIR DUCT
Remove the bolt.
Detach the claw and remove the No. 1 air duct.
When removing, do not crack or deform the lower heater case of the air conditioning radiator assembly.
If the No. 1 air duct is reused, it may fall off or abnormal noise may occur. Therefore, make sure to replace it with a new one.
87211A
15.REMOVE NO. 2 AIR DUCT
Detach the claw and remove the No. 2 air duct.
When removing, do not crack or deform the lower heater case of the air conditioning radiator assembly.
If the No. 2 air duct is reused, it may fall off or abnormal noise may occur. Therefore, make sure to replace it with a new one.
16.REMOVE STEERING COLUMN ASSEMBLY
67914B
17.REMOVE FRONT DOOR SCUFF PLATE LH
for Double Cab:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for Double Cab)>REMOVAL
for Single Cab:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for Single Cab)>REMOVAL
for Smart Cab:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for Smart Cab)>REMOVAL
62112
18.REMOVE COWL SIDE TRIM BOARD LH
67913B
19.REMOVE FRONT DOOR SCUFF PLATE RH
for Double Cab:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for Double Cab)>REMOVAL
for Single Cab:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for Single Cab)>REMOVAL
for Smart Cab:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for Smart Cab)>REMOVAL
62111C
20.REMOVE COWL SIDE TRIM BOARD RH
67918E
21.REMOVE REAR DOOR SCUFF PLATE LH (for Double Cab)
67917C
22.REMOVE REAR DOOR SCUFF PLATE RH (for Double Cab)
62414A
23.REMOVE LOWER CENTER PILLAR GARNISH LH (for Double Cab)
62413A
24.REMOVE LOWER CENTER PILLAR GARNISH RH (for Double Cab)
25.REMOVE FRONT FLOOR CARPET ASSEMBLY
for LHD:
Remove the 5 clips.
| *A | for LHD | - | - |
|
Fastener |
|
Remove in this Direction |
for RHD:
Remove the 4 clips.
Detach each fastener.
Detach the guide and fold back the front floor carpet assembly as shown in the illustration.
55395C
26.REMOVE NO. 1 INSTRUMENT PANEL INNER BRACKET COVER LH (for LHD)
Remove the 3 clips and No. 1 instrument panel inner bracket cover LH
55215D
27.REMOVE NO. 3 DASH PANEL INSULATOR PAD
|
Remove in this Direction |
Remove the No. 3 dash panel insulator pad as shown in the illustration.
55214C
28.REMOVE NO. 2 DASH PANEL INSULATOR PAD
|
Remove in this Direction |
Remove the No. 2 dash panel insulator pad as shown in the illustration.
55306A
29.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
|
Nut |
|
Bolt |
|
Screw |
Detach the clamp.
Remove the nut, bolt, 4 screws and No. 1 instrument panel brace sub-assembly.
55307C
30.REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
|
Nut |
|
Bolt |
|
Screw |
Remove the nut, bolt, 3 screws and No. 2 instrument panel brace sub-assembly.
82141
31.DISCONNECT INSTRUMENT PANEL WIRE
for Automatic Air Conditioning System:
Disconnect the connector.
Detach the clamp.
for Manual Cooler System:
Disconnect the connector.
Detach the clamp.
Remove each bolt and each ground wire.
| *A | for Manual Air Conditioning System | *B | for Automatic Air Conditioning System |
| *1 | Ground Wire | - | - |
Disconnect each connector and detach each clamp.
Remove each bolt, nut and screw, and then disconnect the instrument panel wire.
55330B
32.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY
Be sure to support the air conditioning unit assembly when removing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.
When removing the air conditioning unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.
| *A | for Driver Side |
|
Protective Tape |
Put protective tape around the hole plug.
Using a screwdriver with its tip wrapped with protective tape, remove the 2 hole plugs.
for Automatic Transmission:
Remove the 11 bolts.
| *A | for Manual Transmission | - | - |
|
Bolt A |
|
Bolt B |
|
Bolt C |
|
Bolt D |
for Manual Transmission:
Remove the 12 bolts.
55950G
33.REMOVE DEFROSTER NOZZLE ASSEMBLY
Detach the claw and remove the defroster nozzle assembly.
34.REMOVE AIR CONDITIONING UNIT ASSEMBLY
Be sure to support the air conditioning unit assembly when removing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.
When disassembling the air conditioning unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.
Disconnect the drain cooler hose.
Remove the nut and air conditioning unit assembly and instrument panel reinforcement assembly.
87211B
35.REMOVE NO. 3 AIR DUCT
Detach the claw and remove the No. 3 air duct.