Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)
RM33J0E _56 Audio / Visual / Telematics _038485 AUDIO / VIDEO _0193314 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Steering Pad Switch Circuit  


DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the radio receiver assembly.

If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.

If there is a short in the circuit, the same condition as when the switch is continuously depressed occurs.

Therefore, the radio receiver assembly cannot be operated using the steering pad switch assembly, and the radio receiver assembly itself cannot function.

WIRING DIAGRAM

E323302E06
1.719,1.031 2.948,1.229 1.229,0.198 10 false Off Hook 2.479,1.042 3.708,1.24 1.229,0.198 10 false On Hook 3.271,1.063 4.5,1.26 1.229,0.198 10 false Mode 1.021,1.927 2.25,2.125 1.229,0.198 10 false Volume- 1.771,1.938 3,2.135 1.229,0.198 10 false Volume+ 2.542,1.927 3.771,2.125 1.229,0.198 10 false Seek- 3.292,1.917 4.521,2.115 1.229,0.198 10 false Seek+ 1.333,2.854 4.052,3.073 2.719,0.219 10 false Steering Pad Switch Assembly 4.417,0.635 4.833,0.854 0.417,0.219 10 false z2 4.417,1.5 4.833,1.719 0.417,0.219 10 false z2 4.417,2.365 4.833,2.583 0.417,0.219 10 false z2 4.406,0.438 4.823,0.656 0.417,0.219 10 false 11 4.458,1.313 4.875,1.531 0.417,0.219 10 false 8 4.417,2.167 4.833,2.385 0.417,0.219 10 false 10 5.417,0.635 5.833,0.854 0.417,0.219 10 false G4 5.406,1.5 5.823,1.719 0.417,0.219 10 false G4 5.406,2.365 5.823,2.583 0.417,0.219 10 false G4 5.469,0.448 5.885,0.667 0.417,0.219 10 false 6 5.479,1.302 5.896,1.521 0.417,0.219 10 false 3 5.458,2.167 5.875,2.385 0.417,0.219 10 false 5 4.844,0.531 5.26,0.75 0.417,0.219 10 false AU1 4.844,1.406 5.26,1.625 0.417,0.219 10 false EAU 4.833,2.271 5.25,2.49 0.417,0.219 10 false AU2 5.865,0.521 6.281,0.74 0.417,0.219 10 false 21 5.865,1.396 6.281,1.615 0.417,0.219 10 false 23 5.854,2.271 6.271,2.49 0.417,0.219 10 false 22 6.167,0.635 6.583,0.854 0.417,0.219 10 false SW1 6.135,1.49 6.552,1.708 0.417,0.219 10 false SWG 6.135,2.365 6.552,2.583 0.417,0.219 10 false SW2 6.063,2.823 6.479,3.042 0.417,0.219 10 false G113 6.073,2.99 7.031,3.333 0.958,0.344 10 false Radio Receiver Assembly 4.26,2.813 5.781,3.125 1.521,0.313 10 false Spiral with Sensor Cable Sub-assembly*1 4.25,3.458 6.083,3.802 1.833,0.344 10 false Spiral Cable Sub-assembly*2 0.24,3.125 1.094,3.323 0.854,0.198 10 false *1: w/ VSC 0.229,3.396 1.083,3.594 0.854,0.198 10 false *2: w/o VSC

CAUTION / NOTICE / HINT

NOTICE:

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

for Type A: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION

for Type B: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


PROCEDURE

1.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK VEHICLE CONDITION

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

2.CHECK VEHICLE CONDITION
a.

Check the vehicle condition.


Result:
Result Proceed to
w/ VSC A
w/o VSC B



A

3.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

B

5.INSPECT SPIRAL CABLE SUB-ASSEMBLY
3.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY
a.

Remove the spiral with sensor cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral with sensor cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY AND BODY GROUND)

NG

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY AND BODY GROUND)
a.

Disconnect the G113 radio receiver assembly connector.


b.

Disconnect the G4 spiral with sensor cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G113-21 (SW1) - G4-6 (AU1) Always Below 1 Ω
G113-22 (SW2) - G4-5 (AU2) Always Below 1 Ω
G113-23 (SWG) - Body ground Always Below 1 Ω
G4-3 (EAU) - Body ground Always Below 1 Ω
G113-21 (SW1) or G4-6 (AU1) - Body ground Always 10 kΩ or higher
G113-22 (SW2) or G4-5 (AU2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY AND BODY GROUND)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY AND BODY GROUND)
a.

Disconnect the G113 radio receiver assembly connector.


b.

Disconnect the G4 spiral cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G113-21 (SW1) - G4-6 (AU1) Always Below 1 Ω
G113-22 (SW2) - G4-5 (AU2) Always Below 1 Ω
G113-23 (SWG) - Body ground Always Below 1 Ω
G4-3 (EAU) - Body ground Always Below 1 Ω
G113-21 (SW1) or G4-6 (AU1) - Body ground Always 10 kΩ or higher
G113-22 (SW2) or G4-5 (AU2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR