Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM
RM33J0E _51 Engine / Hybrid System _038446 2KD-FTV ENGINE CONTROL _0195892 ECD SYSTEM C

2KD-FTV ENGINE CONTROL  ECD SYSTEM  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate that the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0504 Brake Switch "A" / "B" Correlation Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic):
(a) Ignition switch to ON.
(b) Brake pedal is released.
(c) The STP signal is off when the ST1- signal is off, or the STP signal is on when the ST1- signal is on.
·

Open or short in stop light switch signal circuit

·

STOP fuse

·

IGN fuse

·

Stop light switch

·

ECM


- DTC stored

Related Data List
DTC No. Data List
P0504 Stop Light Switch

CONFIRMATION DRIVING PATTERN

P0504
DTC Detection Drive Pattern Depress and release brake pedal with ignition switch to ON

WIRING DIAGRAM

A355787E02
2.104,2.677 3.146,2.865 1.042,0.188 10 false FL MAIN 3.0W 0.844,2.677 1.302,2.854 0.458,0.177 10 false J/B-B 0.542,1.885 1.354,2.083 0.813,0.198 10 false AM2 NO. 2 0.781,1.49 1.771,1.719 0.99,0.229 10 false Ignition Switch 0.771,1.333 1.229,1.51 0.458,0.177 10 false G1 0.844,1.073 1.302,1.25 0.458,0.177 10 false AM2 1.344,1.073 1.802,1.25 0.458,0.177 10 false IG2 1.656,0.823 2.115,1 0.458,0.177 10 false 3 5.281,0.823 5.74,1 0.458,0.177 10 false 3 0.677,0.823 1.135,1 0.458,0.177 10 false 4 4.219,0.823 4.677,1 0.458,0.177 10 false 4 4.229,1.427 4.688,1.604 0.458,0.177 10 false 2 5.271,1.427 5.729,1.604 0.458,0.177 10 false 1 4.375,1.917 4.833,2.094 0.458,0.177 10 false A35 4.375,2.083 5.563,2.333 1.188,0.25 10 false Stop Light Switch 2.74,1.073 3.552,1.271 0.813,0.198 10 false IG2 NO. 3 2.323,1.688 2.781,1.865 0.458,0.177 10 false ALT 3.438,1.688 3.896,1.865 0.458,0.177 10 false STOP 3.844,3 4.552,3.177 0.708,0.177 10 false Battery 5.875,1.531 6.333,1.708 0.458,0.177 10 false G83 5.865,0.927 6.323,1.104 0.458,0.177 10 false G83 5.875,2.521 6.333,2.698 0.458,0.177 10 false C56 6.208,2.51 6.667,2.688 0.458,0.177 10 false E1 6.208,1.521 6.667,1.698 0.458,0.177 10 false STP 6.208,0.917 6.667,1.094 0.458,0.177 10 false ST1- 6.302,3.469 6.76,3.646 0.458,0.177 10 false ECM 5.917,0.708 6.375,0.885 0.458,0.177 10 false 14 5.906,1.323 6.365,1.5 0.458,0.177 10 false 15 5.948,2.302 6.406,2.479 0.458,0.177 10 false 7

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).



PROCEDURE

1.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL B VOLTAGE)
a.
A253393C18
0.823,1.031 1.188,1.313 0.365,0.281 0.198,0.104 0.51,0.302 0.313,0.198 10 false *a 0.885,1.094 1.198,1.292 0.313,0.198 10 false A35
*a Front view of wire harness connector
(to Stop Light Switch)


Disconnect the stop light switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A35-2 - Body ground Always 11 to 14 V
A35-4 - Body ground Ignition switch ON 11 to 14 V



c.

Reconnect the stop light switch connector.


Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK ECM (STP AND ST1- VOLTAGE)

NG

5.REPLACE STOP LIGHT SWITCH ASSEMBLY
3.CHECK ECM (STP AND ST1- VOLTAGE)
a.
A303106C08
1.938,2.531 2.354,2.792 0.417,0.26 1.552,3.938 1.927,3.177 true 2.333,3.906 1.979,3.177 true 0.167,0.083 0.479,0.281 0.313,0.198 10 false *a 1.771,0.083 2.083,0.281 0.313,0.198 10 false *b 0.25,2.219 0.563,2.417 0.313,0.198 10 false *c 2,2.573 2.313,2.771 0.313,0.198 10 false G83 1.292,3.948 1.896,4.198 0.604,0.25 10 false 15 (STP) 2.271,3.948 2.896,4.198 0.625,0.25 10 false 14 (ST1-)
*a Brake Pedal Depressed
*b Brake Pedal Released
*c Component with harness connected
(ECM)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Condition Specified Condition
G83-14 (ST1-) - Body ground Released 11 to 14 V
Depressed 0 to 3 V
G83-15 (STP) - Body ground Released 0 to 3 V
Depressed 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE STOP LIGHT SWITCH ASSEMBLY
a.

Replace the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Depress and release the brake pedal.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

g.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END