Home › Engine / Hybrid System › 2GD-FTV ENGINE MECHANICAL › ENGINE UNIT
RM33J0E _51 Engine / Hybrid System _038438 2GD-FTV ENGINE MECHANICAL _0196036 ENGINE UNIT A

2GD-FTV ENGINE MECHANICAL  ENGINE UNIT  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


·

Supply pump assembly

·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.

·

The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.

·

The common rail assembly is a precision instrument. Do not use the common rail assembly if it is struck or dropped.

·

Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.

·

Hold the common rail assembly itself during removal and installation. Do not hold the pressure discharge valve or fuel pressure sensor, etc.

·

Make sure foreign matter does not enter the fuel path.



PROCEDURE

Hide 16575C 1.INSTALL NO. 1 WATER HOSE CLAMP BRACKET (w/ DPF)

a.

Install the No. 1 water hose clamp bracket with the bolt to the timing chain case assembly.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11382C 4.INSTALL CAMSHAFT OIL SEAL RETAINER

NOTICE:

If the camshaft oil seal retainer is dropped, replace it with a new one.


a.

Before installing a new camshaft oil seal retainer, clean the installation surface of the No. 3 camshaft bearing cap and cylinder head sub-assembly and remove any foreign matter.


b.
A343512C01
2.594,0.823 2.594,0.146 2.594,0.146 2.781,0.146 true 0.563,1.292 0.76,1.292 0.76,1.292 1.313,2.333 true 2.802,0.917 2.802,0.385 2.802,0.385 2.99,0.385 true 3.021,0.302 3.333,0.458 0.313,0.156 10 false *1 2.604,2.99 2.917,3.146 0.313,0.156 10 false *a 0.271,1.198 0.729,1.396 0.458,0.198 10 false SST 2.833,0.063 3.292,0.26 0.458,0.198 10 false SST
*1 Camshaft Oil Seal Retainer
*a Depth


Using SST and a hammer, tap in a new camshaft oil seal retainer to the No. 3 camshaft bearing cap and cylinder head sub-assembly as shown in the illustration.

SST
09223-46011  

Standard depth:

0 to 0.8 mm (0 to 0.0315 in.)



Hide 29300 5.INSTALL VACUUM PUMP ASSEMBLY

a.
A343513

Coat 2 new O-rings with engine oil, and install them to the vacuum pump assembly.


b.
A343514N01
2.615,0.469 2.427,0.469 2.427,0.469 2.281,0.885 true 1.198,1.781 1.198,1.281 true 1.156,1.802 1.333,1.99 0.177,0.188 10 true A 2.667,0.385 2.844,0.573 0.177,0.188 10 true B

Install the vacuum pump assembly so that the coupling teeth of the vacuum pump assembly labeled A and the groove of the No. 2 camshaft labeled B can engage.


c.

Install the vacuum pump assembly with the 3 bolts to the cylinder head sub-assembly.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 25706 6.INSTALL NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

a.

Install the No. 1 vacuum transmitting pipe sub-assembly with the 3 bolts to the cylinder head sub-assembly.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the No. 1 vacuum transmitting hose to the vacuum pump assembly.


Hide 16620 7.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

Hide 16603 8.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY

Hide 16321 10.INSTALL WATER INLET

a.

Install the water inlet with the 3 bolts to the timing chain cover sub-assembly.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 16304 11.INSTALL WATER OUTLET SUB-ASSEMBLY

a.

Install a new gasket and the water outlet sub-assembly with the 4 bolts and 2 nuts to the timing chain cover sub-assembly.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16207 12.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

a.

Install the No. 2 water by-pass pipe sub-assembly with the 2 bolts to the engine water pump assembly and water inlet.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the No. 3 water by-pass hose to the water outlet sub-assembly, and slide the clamp to secure the hose.


Hide 83530 13.INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY

Hide 15407 14.TEMPORARILY INSTALL TURBO OIL INLET PIPE SUB-ASSEMBLY

Hide 17141 15.TEMPORARILY INSTALL EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY

Hide 17141 18.TIGHTEN EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY

Hide 16284 20.CONNECT NO. 1 AND NO. 2 TURBO WATER HOSE

Hide 16268 21.INSTALL NO. 1 WATER BY-PASS PIPE

a.

Install a new gasket and the No. 1 water by-pass pipe with the 3 bolts to the timing chain cover sub-assembly.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:

Make sure that the claw of the gasket faces the No. 1 water by-pass pipe.



Hide 89467B 28.INSTALL AIR FUEL RATIO SENSOR (w/ DPF)

Hide 23295D 29.INSTALL NO. 1 INJECTOR HOLDER (w/ DPF)

Hide 16281 30.CONNECT NO. 4 WATER BY-PASS HOSE (w/ DPF)

a.

Connect the No. 4 water by-pass hose to the No. 1 injector holder, and slide the clamp to secure the hose.


Hide 16282 31.INSTALL NO. 5 WATER BY-PASS HOSE (w/ DPF)

a.

Attach the clamp and install the No. 5 water by-pass hose to the No. 1 water hose clamp bracket.


b.

Connect the No. 5 water by-pass hose to the No. 1 injector holder and water outlet sub-assembly, and slide the 2 clamps to secure the hose.


Hide 89422C 32.INSTALL ENGINE COOLANT TEMPERATURE SENSOR

Hide 88431 33.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET

NOTICE:

Install the No. 1 compressor mounting bracket exactly as described in the procedures below to properly secure and prevent damage to the fan and generator V belt.


a.
A354055

Temporarily install the No. 1 compressor mounting bracket with the 2 bolts to the cylinder block sub-assembly.

HINT:

Temporarily install the No. 1 compressor mounting bracket with the 2 bolts so that the No. 1 compressor mounting bracket can be moved by hand.



b.
A354056C01
1.156,3.313 1.344,3.479 0.188,0.167 10 true *a 1.906,4.229 2.219,4.385 0.313,0.156 10 false *b 0.552,2.479 0.865,2.635 0.313,0.156 10 false *c 0.698,1.219 0.854,1.417 0.156,0.198 10 true A 2.51,4.229 2.823,4.385 0.313,0.156 10 false *b 2.667,3.313 2.854,3.479 0.188,0.167 10 true *a 3.229,3.313 3.417,3.479 0.188,0.167 10 true *a
*a No Clearance
*b Push
*c Front


Push the No. 1 compressor mounting bracket toward the cylinder block sub-assembly as shown in the illustration and tighten bolt A.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)

HINT:

Make sure there is no clearance between the cylinder block sub-assembly and No. 1 compressor mounting bracket as shown in the illustration.



c.
A354057N01
2.615,1.406 2.771,1.604 0.156,0.198 10 true 3 3.031,0.396 3.188,0.594 0.156,0.198 10 true 2 0.844,0.281 1,0.479 0.156,0.198 10 true 1

Uniformly tighten the 3 bolts in the order shown in the illustration.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


Hide 16025 34.INSTALL NO. 5 WATER BY-PASS PIPE SUB-ASSEMBLY

a.

Install a new gasket and the No. 5 water by-pass pipe sub-assembly with the 3 bolts to the cylinder block sub-assembly.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

HINT:

Make sure that the claw of the gasket faces the No. 5 water by-pass pipe sub-assembly.



Hide 23780 35.INSTALL NO. 3 NOZZLE LEAKAGE PIPE (w/o Pressurized Fuel Filter)

a.

Install the No. 3 nozzle leakage pipe with the 2 nuts to the cylinder block sub-assembly.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 23300 36.INSTALL FUEL FILTER ASSEMBLY (w/ Pressurized Fuel Filter)

a.

Install the fuel filter assembly with the 2 nuts to the cylinder block sub-assembly.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 44781 37.INSTALL HOSE BRACKET

a.

Install the hose bracket with the 2 bolts to the cylinder head sub-assembly.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 19850 38.INSTALL GLOW PLUG ASSEMBLY

Hide 19871 39.INSTALL NO. 1 GLOW PLUG CONNECTOR

Hide 23810A 40.INSTALL COMMON RAIL ASSEMBLY

Hide 23701 41.TEMPORARILY INSTALL NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 23670 42.TIGHTEN INJECTOR ASSEMBLY

Hide 23701 43.TIGHTEN NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 44.INSTALL WIRING HARNESS CLAMP BRACKET

a.
A343500N01
0.24,0.969 0.396,1.167 0.156,0.198 10 true A 3.135,1.021 3.313,1.188 0.177,0.167 10 true B

Install the 2 wiring harness clamp brackets with the 2 bolts to the cylinder head cover sub-assembly.

Torque:
for bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for bolt B : 8.4 N*m (86 kgf*cm, 74 in.*lbf)


Hide 23760 45.INSTALL NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 47.INSTALL WIRING HARNESS CLAMP BRACKET

Hide 23770 49.INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 23804C 50.INSTALL FUEL INLET PIPE SUB-ASSEMBLY

Hide 23815D 51.INSTALL NO. 3 FUEL PIPE (w/ Pressurized Fuel Filter)

Hide 23804D 52.INSTALL NO. 4 FUEL PIPE SUB-ASSEMBLY (w/ Pressurized Fuel Filter)

Hide 23271H 53.INSTALL NO. 1 FUEL HOSE

Hide 23273H 54.INSTALL NO. 2 FUEL HOSE

Hide 23243B 55.INSTALL FUEL PUMP MOTOR WIRE

Hide 22803 56.INSTALL FUEL INJECTION PUMP COVER SUB-ASSEMBLY

Hide 58.INSTALL WIRING HARNESS CLAMP BRACKET

Hide 23812D 59.INSTALL NO. 2 FUEL PIPE

a.

Install the No. 2 fuel pipe with the bolt to the manifold stay.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the No. 1 fuel hose to the No. 2 fuel pipe, and slide the clamp to secure the hose.


Hide 11409 60.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 25800 61.INSTALL NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY

Hide 62.INSTALL EGR PIPE WITH COOLER SUB-ASSEMBLY (w/ DPF)

a.

Using an E8 "TORX" socket wrench, install 2 new stud bolts to the exhaust manifold.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Install 2 new gaskets and the EGR pipe with cooler sub-assembly with the bolt and 4 new nut to the exhaust manifold, electric EGR control valve assembly and No. 1 vacuum transmitting pipe sub-assembly.

Torque:
for bolt : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for nut : 29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 16209 63.INSTALL NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY

a.

w/ DPF:

i.

Install the No. 4 water by-pass pipe sub-assembly with the 2 bolts to the intake manifold.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


ii.

Connect the No. 17 water by-pass hose to the EGR pipe with cooler sub-assembly, and slide the clamp to secure the hose.


iii.

Connect the water hose to the No. 2 EGR valve assembly, and slide the clamp to secure the hose.


iv.

Connect the No. 7 water by-pass hose to the No. 4 water by-pass pipe sub-assembly, and slide the clamp to secure the hose.


v.

Connect the No. 6 water by-pass hose to the No. 4 water by-pass pipe sub-assembly, and slide the clamp to secure the hose.



b.

w/o DPF:

i.

Install the No. 4 water by-pass pipe sub-assembly with the 2 bolts to the intake manifold.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


ii.

Connect the water hose to the No. 2 EGR valve assembly, and slide the clamp to secure the hose.


iii.

Connect the No. 7 water by-pass hose to the No. 4 water by-pass pipe sub-assembly, and slide the clamp to secure the hose.


iv.

Connect the No. 6 water by-pass hose to the No. 4 water by-pass pipe sub-assembly, and slide the clamp to secure the hose.



Hide 25804 64.INSTALL VACUUM CONTROL VALVE SET

Hide 25601 65.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY (w/o DPF)

a.

Using an E8 "TORX" socket wrench, install 2 new stud bolts to the exhaust manifold.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Install 2 new gaskets and the No. 1 EGR pipe sub-assembly with the bolt and 4 new nut to the exhaust manifold, electric EGR control valve assembly and No. 1 vacuum transmitting pipe sub-assembly.

Torque:
for bolt : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for nut : 29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 27148A 66.INSTALL CONNECTING WIRE

a.

Attach the 2 clamps and install the connecting wire to the hose bracket.


b.

Connect the connector to the common rail assembly.


Hide 16206B 67.INSTALL NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 25625 69.INSTALL EGR VALVE BRACKET

Hide 12631A 72.INSTALL ENGINE COVER BRACKET

a.

Install the engine cover bracket with the 2 bolts to the cylinder head cover sub-assembly and hose bracket.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 25734 74.TEMPORARILY INSTALL NO. 2 VACUUM PIPE (w/ DPF)

Hide 25733A 75.TEMPORARILY INSTALL NO. 1 VACUUM PIPE (w/ DPF)

Hide 89425 78.INSTALL EXHAUST GAS TEMPERATURE SENSOR (w/ DPF)

Hide 89481B 79.INSTALL DIFFERENTIAL PRESSURE SENSOR (w/ DPF)

Hide 16278 80.INSTALL NO. 2 WATER BY-PASS PIPE

Hide 26100G 81.INSTALL DIESEL THROTTLE BODY ASSEMBLY

Hide 82121 83.INSTALL ENGINE WIRE

Hide 12632 84.INSTALL NO. 2 ENGINE COVER BRACKET

Hide 44763C 85.INSTALL NO. 2 HOSE TO HOSE TUBE

a.

Install the No. 2 hose to hose tube to the cylinder head cover sub-assembly and hose bracket with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the union to check valve hose to the vacuum pump assembly, and slide the clamp to secure the hose.