Home › Engine / Hybrid System › 2GD-FTV FUEL › FUEL SUPPLY PUMP
RM33J0E _51 Engine / Hybrid System _038439 2GD-FTV FUEL _0199080 FUEL SUPPLY PUMP A

2GD-FTV FUEL  FUEL SUPPLY PUMP  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
·

Injector assembly (including shuffling the injector assemblies between the cylinders)

·

Common rail assembly

·

Cylinder head sub-assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


·

Supply pump assembly

·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.

·

Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.

·

Make sure foreign matter does not enter the fuel path.



PROCEDURE

Hide 22100 1.INSTALL SUPPLY PUMP ASSEMBLY

NOTICE:
·
A347308C03
0.115,0.104 0.51,0.385 0.396,0.281 12 false *A 0.115,2.542 0.458,2.833 0.344,0.292 12 false *B
*A w/ DPF or w/ Pressurized Fuel Filter
*B w/o DPF


Do not hold the supply pump assembly by the parts indicated by the arrows in the illustration.

·

With SST set, do not turn the crankshaft more than a half rotation.



a.

Apply a light coat of engine oil to a new O-ring.


b.

Install the O-ring to the supply pump assembly.


c.
A347065C01
0.958,1.594 1.146,1.594 1.146,1.594 1.427,1.208 true 0.75,1.51 1.063,1.667 0.313,0.156 10 true *a
*a Groove


To insert the supply pump assembly shaft in the supply pump shaft sprocket, it may be necessary to turn the supply pump assembly several degrees and the groove in the supply pump assembly shaft are aligned.

HINT:
A343559C02
2.125,3.302 2.292,2.646 2.292,2.646 2.51,2.646 false 2.521,2.521 2.833,2.677 0.313,0.156 10 false *a 1.208,2.198 1.521,2.354 0.313,0.156 10 false *b 3.063,3.406 3.375,3.563 0.313,0.156 10 false 6°
*a Supply Pump Shaft Key
*b Upper Side


When installing a new supply pump assembly, adjust the supply pump assembly injection pump drive shaft key assignment by turning the supply pump assembly shown in the illustration.



d.
A347066C01
1.635,1.74 2.208,1.74 false 1.156,2.125 1.885,2.125 1.885,2.125 1.885,1.74 false 2.438,0.792 2.583,0.969 2.583,0.969 2.823,0.969 true 0.802,1.979 1.115,2.135 0.313,0.156 10 false *a 2.24,1.635 2.719,1.823 0.479,0.188 10 true SST 2.854,0.875 3.333,1.063 0.479,0.188 10 true SST
*a Hold
V100135

Turn


Using SST, tighten clockwise direction the supply pump assembly, and then temporarily install the 3 fuel supply pump fixing nuts.

SST
09213-58014  (91551-80840)
09330-00021  
09241-11010  


e.
A344940E01
1.365,1.75 1.365,1.49 1.365,1.49 1.656,1.052 true 1.292,1.74 1.521,1.938 0.229,0.198 10 true A

Using SST, tighten and insert the supply pump assembly up to the position shown in the illustration and tighten the 3 fuel supply pump fixing nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

HINT:

After tightening the part with SST, a gap of 2 to 3 mm in area A shown in the illustration is normal.



f.

w/ DPF or w/ Pressurized Fuel Filter:

Install the No. 1 fuel pump bracket with the 2 bolts to the supply pump assembly and cylinder block sub-assembly.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


g.
A344938E01
1.219,1.552 1.417,1.552 1.417,1.552 1.771,1.313 true 0.865,1.458 1.323,1.656 0.458,0.198 10 true SST

Remove SST and the 3 set bolts.


h.
A347061C01
0.948,2.052 1.573,2.052 1.573,2.052 1.573,1.885 false 1.281,1.885 1.844,1.885 false 0.5,1.958 0.813,2.115 0.313,0.156 10 false *a 1.875,1.802 2.333,2 0.458,0.198 10 true SST
*a Hold
V100135

Turn


Using SST, hold the crankshaft pulley sub-assembly and tighten the set nut.

Torque:
137 N*m (1397 kgf*cm, 101 ft.*lbf)


Hide 11324 2.INSTALL TIMING CHAIN COVER PLATE

a.

Install the timing chain cover plate and new gasket with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Do not install the timing chain cover plate with the bolts included with SST.



Hide 3.INSTALL FUEL PUMP MOTOR WIRE

a.

Attach the clamp and install the fuel pump motor wire.


b.

Connect the fuel pump motor wire connector.


Hide 22803 4.INSTALL FUEL INJECTION PUMP COVER SUB-ASSEMBLY

a.

Install the fuel injection pump cover sub-assembly to the supply pump assembly.


Hide 5.INSTALL NO. 4 FUEL PIPE (w/ Pressurized Fuel Filter)

a.
A370020E01
0.271,2.292 0.479,2.469 0.208,0.177 10 true 1 1.781,2.958 1.99,3.135 0.208,0.177 10 true 2

Tighten the 2 union bolts and bolts in the order shown in the illustration.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 23273H 6.INSTALL NO. 2 FUEL HOSE

a.

Install the No. 2 fuel hose to the supply pump assembly and No. 3 nozzle leakage pipe assembly, and slide the 2 clamps to secure it.


Hide 23271H 7.INSTALL NO. 1 FUEL HOSE

a.

Install the No. 1 fuel hose to the supply pump assembly and No. 2 fuel pipe, and slide the 2 clamps to secure it.


Hide 16620 8.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

Hide 16470 10.INSTALL RADIATOR RESERVOIR

Hide 44369A 11.INSTALL NO. 1 OIL RESERVOIR BRACKET

Hide 44360 12.CONNECT VANE PUMP OIL RESERVOIR ASSEMBLY

Hide 16571C 13.INSTALL NO. 1 RADIATOR HOSE

Hide 17362B 14.INSTALL NO. 2 AIR TUBE

Hide 17344E 15.INSTALL NO. 4 AIR HOSE

Hide 17.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 51441 20.INSTALL NO. 1 ENGINE UNDER COVER