When the entry operation and wireless operation of the door lock functions do not operate, a malfunction or wave interference may be occurring in either of the following: 1) the certification ECU (smart key ECU assembly); or 2) the electrical key transmitter sub-assembly. If the entry lock and wireless lock operations cannot be performed, there may be electrical key transmitter sub-assembly malfunctions, wave interference or problems in the communication which is used for the entry and wireless function.
The smart entry and start system (for Entry Function) uses the CAN communication system and LIN communication system. First inspect the communication systems by following How to Proceed with Troubleshooting.
Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN).
While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Check that there are no electrical key transmitter sub-assemblies in the vehicle.
Before performing the inspection, check that DTC B1242 (wireless door lock control) or DTC B27B0 is not output.
Inspect the fuses for circuits related to this system before performing the following procedure.
Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution.
After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".
w/ Door Control Battery:
As the door control battery is installed between the vehicle battery and body ECU, first perform the inspections to confirm that there are no malfunctions in the power source circuit for the body ECU before performing this troubleshooting procedure.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION
w/ Automatic Light Control System:
If the body ECU has been replaced, it is necessary to initialize the body ECU.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
If all door entry lock and unlock functions do not operate, the cause of the malfunction may be stored in the certification ECU (smart key ECU assembly).
If the cause of the malfunction is stored in the certification ECU (smart key ECU assembly), the following table is helpful in checking whether the malfunction was caused by wave interference.
| Tester Display |
|---|
| Operation History |
| Parameter Name | Cause of Problem and Countermeasure |
|---|---|
| Lock / Key RF Signal Interference | When entry lock operation was performed, the electrical key transmitter sub-assembly could not be confirmed due to wave interference.
If the cause of the malfunction has not been stored but the vehicle has been moved and an entry lock operation has been successfully performed, the possibility of wave interference is high. |
| Unlock / Key RF Signal Interference | When entry unlock operation was performed, the electrical key transmitter sub-assembly could not be confirmed due to wave interference.
If the cause of the malfunction has not been stored but the vehicle has been moved and an entry unlock operation has been successfully performed, the possibility of wave interference is high. |
Measure the voltage of the vehicle battery.
11 to 14 V
It may be possible to tell whether the vehicle battery is discharged by operating the horn.
If the voltage is below 11 V, recharge or replace the vehicle battery before proceeding.
| Proceed to |
|---|
| NEXT |
NEXT
Open the driver door using the mechanical key built into the electrical key transmitter sub-assembly.
Connect the GTS and check for DTCs.
When using the GTS with the engine switch off to troubleshoot: Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.
DTC is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
When door unlock by entry lock or wireless door lock operation functions even though all doors are closed, check the door ajar warning operation.
| Result | Proceed to |
|---|---|
| Door ajar warning does not operate. | A |
| Door ajar warning operates. | B |
A
B
When the door control switch on the power window master switch on the driver door is operated, check that the doors unlock and lock according to the switch operation.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
Door locks operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check the following antennas in key diagnostic mode.
Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
| *A | for LHD |
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
| *A | for RHD |
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
Check the electrical key antenna (for Driver Door):
When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for Driver Door), check that the wireless door lock buzzer sounds.
| *A | for LHD |
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
| *A | for RHD |
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
Check the electrical key antenna (for Front Passenger Door):
When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for Front Passenger Door), check that the wireless door lock buzzer sounds.
| *a | Inspection Point |
Check the No. 1 indoor electrical key antenna assembly (front floor):
When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.
| *a | Inspection Point |
Check the No. 2 indoor electrical key antenna assembly (rear floor):
When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.
Wireless door lock buzzer sounds.
| Result | Proceed to |
|---|---|
| Diagnostic mode inspections fail for both channels | A |
| Diagnostic mode inspections succeed for both channels | B |
| Diagnostic mode inspection succeeds for only one of the channels | C |
A
B
C
Bring the electrical key transmitter sub-assembly near the door control receiver and perform a wireless and entry function operation check.
When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.
Wireless and entry functions operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.
Press and hold the lock switch of the transmitter for 5 seconds and check the number of times that the transmitter LED illuminates.
| Result | Proceed to |
|---|---|
| Transmitter LED does not illuminate when switch is pressed and held | A |
| Transmitter LED illuminates 3 times or more when switch is pressed and held | B |
| Transmitter LED illuminates once or twice but not a third time | C |
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less.
Even if the transmitter battery is depleted, it is still possible to start the engine by holding the electrical key transmitter sub-assembly against the engine switch, depressing the brake pedal and pressing the engine switch.
A
B
C
Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT
Inspect the transmitter battery.
When removing the transmitter battery, make sure not to touch the electronic circuit board, as static electricity may cause a malfunction to occur.
Measure the voltage of the transmitter battery.
Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/ Smart Entry and Start System)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT
Check if there are any other registered electrical key transmitter sub-assemblies.
| Result | Proceed to |
|---|---|
| There are no other registered electrical key transmitter sub-assemblies | A |
| There is another registered electrical key transmitter sub-assembly | B |
A
B
Register a new electrical key transmitter sub-assembly.
Refer to the Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Using another registered electrical key transmitter sub-assembly, check if an entry lock/unlock operation can be performed twice in succession.
Click here
Entry lock/unlock operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G69 and G70 certification ECU (smart key ECU assembly) connectors.
Disconnect the G73 door control receiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G70-3 (RCO) - G73-4 (+5) | Always | Below 1 Ω |
| G70-22 (RDAS) - G73-5 (DATA) | Always | Below 1 Ω |
| G70-21 (CSEL) - G73-2 (CSEL) | Always | Below 1 Ω |
| G69-10 (E) - Body ground | Always | Below 1 Ω |
| G73-1 (GND) - Body ground | Always | Below 1 Ω |
| G70-3 (RCO) or G73-4 (+5) - Body ground | Always | 10 kΩ or higher |
| G70-22 (RDAS) or G73-5 (DATA) - Body ground | Always | 10 kΩ or higher |
| G70-21 (CSEL) or G73-2 (CSEL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the G69 and G70 certification ECU (smart key ECU assembly) connectors.
Connect the G73 door control receiver connector.
Check the entry lock/unlock operation.
| Result | Proceed to |
|---|---|
| Entry lock/unlock does not operate | A |
| Entry lock/unlock operate normally | B |
A
B
Measure the resistance according to the value(s) in the table below.
| *a | Component with harness connected
(Door Control Receiver) |
*b | Waveform 1 |
| *c | Before lock or unlock button of electrical key transmitter sub-assembly pressed | *d | After lock or unlock button of electrical key transmitter sub-assembly pressed |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G73-1 (GND) - Body ground | Always | Below 1 Ω |
Using an oscilloscope, check the waveform.
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| G73-5 (DATA) - G73-1 (GND) | Procedure:
1.
Engine switch off 2.
All doors locked 3.
Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed |
5 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| *a | Component with harness connected
(Door Control Receiver) |
*b | Waveform 1 |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G73-4 (+5) - G73-1 (GND) | Procedure:
1.
All doors closed 2.
All doors locked 3.
Electrical key transmitter sub-assembly switch pressed |
Below 1 V → 4.5 to 5.5 V |
Using an oscilloscope, check the waveform.
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| G73-2 (CSEL) - G73-1 (GND) | Procedure:
1.
Engine switch off 2.
All doors closed |
2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the certification ECU (smart key ECU assembly) with a new one.
Refer to the Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Check that the wireless door lock functions operate normally.
Wireless door lock functions operate normally.
| Proceed to |
|---|
| OK |
| NG (for LHD) |
| NG (for RHD) |
OK
NG (for LHD)
NG (for RHD)
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
- | - |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Power Supply Condition | Power supply state | ST ON, ALL OFF, IG ON or ACC ON | ALL OFF: Engine switch off (ACC and IG)
ACC ON: Engine switch on (ACC) IG ON: Engine switch on (IG) (IG1 relay on) ST ON: Sending engine start request signal |
- |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G69-20 (IG1D) - Body ground | Engine switch off | Below 1 V |
| Engine switch on (ACC) | Below 1 V | |
| Engine switch on (IG) | 9 V or higher | |
| G69-21 (ACCD) - Body ground | Engine switch off | Below 1 V |
| Engine switch on (ACC) | 8.5 V or higher | |
| Engine switch on (IG) | 8.5 V or higher |
Using the GTS, measure the voltage while confirming the power source mode on the Data List.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the certification ECU (smart key ECU assembly) connectors.
| *a | Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly)) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G69-10 (E) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G70-33 (CUTB) - Body ground | Always | 11 to 14 V |
| G69-1 (+B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the certification ECU (smart key ECU assembly) connectors.
Check the entry lock/unlock operation.
Entry lock/unlock operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the certification ECU (smart key ECU assembly) with a new one.
Refer to the Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Check that the wireless door lock functions operate normally.
Wireless door lock functions operate normally.
| Proceed to |
|---|
| OK |
| NG (for LHD) |
| NG (for RHD) |
OK
NG (for LHD)
NG (for RHD)
Bring the electrical key transmitter sub-assembly that was checked first near the door control receiver and select the failed channel (the channel in which the buzzer did not sound) to recheck the key diagnostic mode.
When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.
Wireless and entry functions operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check if there are any other registered electrical key transmitter sub-assemblies.
| Result | Proceed to |
|---|---|
| There are no other registered electrical key transmitter sub-assemblies | A |
| There is another registered electrical key transmitter sub-assembly | B |
A
B
Register a new electrical key transmitter sub-assembly.
Refer to the Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Bring another registered electrical key transmitter sub-assembly near the door control receiver and select the failed channel (the channel in which the buzzer did not sound) to recheck the key diagnostic mode.
When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.
Wireless door lock buzzer sounds.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G70 certification ECU (smart key ECU assembly) connector.
Disconnect the G73 door control receiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G70-21 (CSEL) - G73-2 (CSEL) | Always | Below 1 Ω |
| G70-21 (CSEL) or G73-2 (CSEL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the G70 certification ECU (smart key ECU assembly) connector.
Connect the G73 door control receiver connector.
Check the entry lock/unlock operation.
| Result | Proceed to |
|---|---|
| Entry lock/unlock does not operate | A |
| Entry lock/unlock operate normally | B |
A
B
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(Door Control Receiver) |
*b | Waveform 1 |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| G73-2 (CSEL) - G73-1 (GND) | Procedure:
1.
Engine switch off 2.
All doors closed |
2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using an oscilloscope, check the waveform.
Inspection should be performed while the electrical key antenna check in key diagnostic mode is being performed on the failed channel (the channel in which the buzzer did not sound).
| *a | Component with harness connected
(Door Control Receiver) |
*b | Waveform 1 |
| *c | Before lock or unlock button of electrical key transmitter sub-assembly pressed | *d | After lock or unlock button of electrical key transmitter sub-assembly pressed |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| G73-5 (DATA) - G73-1 (GND) | Procedure:
1.
Engine switch off 2.
All doors locked 3.
Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed |
5 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the certification ECU (smart key ECU assembly) with a new one.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Check that the wireless door lock functions operate normally.
Wireless door lock functions operate normally.
| Proceed to |
|---|
| OK |
| NG (for LHD) |
| NG (for RHD) |
OK
NG (for LHD)
NG (for RHD)