If the entry unlock function does not operate for the front passenger door only, but the entry lock function operates, the request code is being transmitted properly from the front passenger door. In this case, there may be a problem related to the except driver door lock position switch system.
The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting.
Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN).
While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Check that there are no electrical key transmitter sub-assemblies in the vehicle.
Before performing the inspection, check that DTC B1242 (wireless door lock control) or B27B0 is not output.
Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution.
After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".
w/ Door Control Battery:
As the door control battery is installed between the vehicle battery and body ECU, first perform the inspections to confirm that there are no malfunctions in the power source circuit for the body ECU before performing this troubleshooting procedure.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION
w/ Automatic Light Control System:
If the body ECU has been replaced, it is necessary to initialize the body ECU.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
When the door control switch on the power window master switch is operated, check that the doors unlock and lock according to the switch operation.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
Door locks operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front door lock assembly (for Front Passenger Door) (lock position switch).
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL
Remove the rear door lock assembly RH/LH (lock position switch).
Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK(for Double Cab)>REMOVAL
Inspect the front door lock assembly LH (lock position switch).
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION
Inspect the rear door lock actuator assembly RH/LH (lock position switch).
Click hereVehicle Interior>DOOR LOCK>REAR DOOR LOCK(for Double Cab)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for LHD
*2: for RHD
Disconnect the G27 body ECU connector.
Disconnect the G69 certification ECU (smart key ECU assembly) connector.
Disconnect the J1*1 or K1*2 front door lock assembly (for Front Passenger Door) connector.
Disconnect the L1 rear door lock assembly RH connector.
Disconnect the M1 rear door lock assembly LH connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G27-2 (LSWP) - G69-9 (LSWP) | Always | Below 1 Ω |
| G27-2 (LSWP) - J1-7 (LSSR) | Always | Below 1 Ω |
| G27-2 (LSWP) - L1-6 (LSSR) | Always | Below 1 Ω |
| G27-2 (LSWP) - M1-6 (LSSR) | Always | Below 1 Ω |
| J1-8 (E) - Body ground | Always | Below 1 Ω |
| L1-9 (E) - Body ground | Always | Below 1 Ω |
| M1-9 (E) - Body ground | Always | Below 1 Ω |
| G27-2 (LSWP) or G69-9 (LSWP) - Body ground | Always | 10 kΩ or higher |
| G27-2 (LSWP) or J1-7 (LSSR) - Body ground | Always | 10 kΩ or higher |
| G27-2 (LSWP) or L1-6 (LSSR) - Body ground | Always | 10 kΩ or higher |
| G27-2 (LSWP) or M1-6 (LSSR) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G27-2 (LSWP) - G69-9 (LSWP) | Always | Below 1 Ω |
| G27-2 (LSWP) - K1-8 (LSSR) | Always | Below 1 Ω |
| G27-2 (LSWP) - L1-6 (LSSR) | Always | Below 1 Ω |
| G27-2 (LSWP) - M1-6 (LSSR) | Always | Below 1 Ω |
| K1-7 (E) - Body ground | Always | Below 1 Ω |
| L1-9 (E) - Body ground | Always | Below 1 Ω |
| M1-9 (E) - Body ground | Always | Below 1 Ω |
| G27-2 (LSWP) or G69-9 (LSWP) - Body ground | Always | 10 kΩ or higher |
| G27-2 (LSWP) or K1-8 (LSSR) - Body ground | Always | 10 kΩ or higher |
| G27-2 (LSWP) or L1-6 (LSSR) - Body ground | Always | 10 kΩ or higher |
| G27-2 (LSWP) or M1-6 (LSSR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the entry lock/unlock operation.
Disconnect and reconnect the connectors of certification ECU (smart key ECU assembly), body ECU and front door lock assembly (for Front Passenger Door) before performing the inspection.
Entry lock/unlock operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the body ECU with a new or known good one.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the entry lock/unlock operation.
Entry lock/unlock operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG