Home › Engine / Hybrid System › 2KD-FTV ENGINE MECHANICAL › ENGINE UNIT
RM33J0E _51 Engine / Hybrid System _038447 2KD-FTV ENGINE MECHANICAL _0201074 ENGINE UNIT A

2KD-FTV ENGINE MECHANICAL  ENGINE UNIT  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
·

Injector assembly (including shuffling the injector assemblies between the cylinders)

·

Common rail assembly

·

Cylinder head sub-assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

No. 3 injection pipe sub-assembly

·

No. 4 injection pipe sub-assembly


·

Supply pump assembly

·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing Gear Case Assembly


Fuel inlet pipe sub-assembly

·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and fuel inlet pipe sub-assembly, clean them with a brush and compressed air.



PROCEDURE

Hide 11322A 1.REMOVE NO. 1 TIMING BELT COVER

Hide 13505 3.REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

Hide 13408 4.REMOVE CRANKSHAFT PULLEY SUB-ASSEMBLY

Hide 12278 5.REMOVE VENTILATION HOSE HEAT INSULATOR

a.

Remove the 2 bolts and ventilation hose heat insulator from the cylinder head sub-assembly.


Hide 88440D 7.REMOVE NO. 2 IDLE PULLEY ASSEMBLY

Hide 12511C 9.REMOVE GENERATOR BRACKET

a.

Remove the bolt and generator bracket.


Hide 16620 10.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

a.
A352057

Remove the 4 bolts and V-ribbed belt tensioner assembly from the cylinder block sub-assembly.


Hide 88431 11.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET

a.

Remove the 4 bolts and No. 1 compressor mounting bracket from the cylinder block sub-assembly.


Hide 16321 12.REMOVE WATER INLET

Hide 16331A 13.REMOVE THERMOSTAT

Hide 16331 14.REMOVE WATER OUTLET

a.
A352058

Remove the 2 bolts, water outlet and gasket from the cylinder head sub-assembly.


Hide 26100G 15.REMOVE DIESEL THROTTLE BODY ASSEMBLY

Hide 25617A 17.REMOVE NO. 2 EGR HOLE COVER PLATE

a.

Remove the 2 nuts and No. 2 EGR hole cover plate.


b.

Remove the gasket.


Hide 19850 18.REMOVE GLOW PLUG ASSEMBLY

Hide 23810A 19.REMOVE COMMON RAIL ASSEMBLY

Hide 22100 20.REMOVE INJECTION OR SUPPLY PUMP ASSEMBLY

Hide 15701C 21.REMOVE OIL COOLER COVER SUB-ASSEMBLY

Hide 29300 22.REMOVE VACUUM PUMP ASSEMBLY

a.
A352059

Remove the 2 nuts, vacuum pump assembly and 2 O-rings from the timing gear cover.


Hide 44320 23.REMOVE VANE PUMP ASSEMBLY

a.
A352060

Remove the 2 nuts, vane pump assembly and O-ring from the timing gear case assembly.


Hide 12311 27.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH

a.
A352061C01
0.083,0.083 0.302,0.25 0.219,0.167 10 true *a 1.833,0.083 2.052,0.25 0.219,0.167 10 true *b
*a LH Side
*b RH Side


Remove the 4 bolts and front No. 1 engine mounting bracket RH from the cylinder block sub-assembly.


Hide 12315 28.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH

a.

Remove the 4 bolts and front No. 1 engine mounting bracket LH from th cylinder block sub-assembly.