Home › Engine / Hybrid System › 1KD-FTV ENGINE MECHANICAL › CAMSHAFT
RM33J0E _51 Engine / Hybrid System _038429 1KD-FTV ENGINE MECHANICAL _0201081 CAMSHAFT A

1KD-FTV ENGINE MECHANICAL  CAMSHAFT  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
·

Injector assembly (including shuffling the injector assemblies between the cylinders)

·

Common rail assembly

·

Cylinder head sub-assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

No. 3 injection pipe sub-assembly

·

No. 4 injection pipe sub-assembly


·

Supply pump assembly

·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing Gear Case Assembly


Fuel inlet pipe sub-assembly

·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and fuel inlet pipe sub-assembly, clean them with a brush and compressed air.



PROCEDURE

Hide 1.INSTALL CAMSHAFT SUB-ASSEMBLY

a.
A352034C01
0.542,1.583 1.583,1.844 1.583,1.844 1.76,1.844 true 1.771,1.729 2.083,1.927 0.313,0.198 10 false *1 0.208,0.99 0.521,1.167 0.313,0.177 10 true 90°
*1 Key


Using the crankshaft pulley bolt, set the No. 1 cylinder to 90° BTDC/compression.

HINT:

Set the No. 1 cylinder to 90° BTDC/compression to prevent the top of the piston from hitting against the valve head.



b.
A352035C01
0.563,0.542 1.427,0.25 1.427,0.25 1.625,0.25 true 1.656,0.135 1.875,0.302 0.219,0.167 10 false *a 0.448,0.063 0.667,0.229 0.219,0.167 10 false *b
*a Key Groove
*b Upward


Install the camshaft sub-assembly.

i.

Apply engine oil to the thrust portion of the intake camshaft sub-assembly.


ii.

Place the intake camshaft sub-assembly on the cylinder head sub-assembly with the key groove facing upward.


iii.
A352036

Align the timing marks (1-dot marks) of the camshaft sub-assembly drive and driven main gears and set the exhaust camshaft sub-assembly in place.



c.

Remove any old seal packing (FIPG material) from the No. 1 camshaft bearing cap.


d.
A352037C01
0.917,1.802 0.917,1.635 0.917,1.635 1.083,1.385 true 1.625,0.875 1.344,0.656 1.344,0.656 1.26,0.656 false 2.677,0.896 2.26,0.479 2.26,0.479 2.177,0.479 false 1.083,0.552 1.313,0.719 0.229,0.167 10 false *a 3.198,0.719 3.406,0.885 0.208,0.167 10 false *b 0.865,1.813 1.094,1.979 0.229,0.167 10 false *c 2.01,0.375 2.24,0.542 0.229,0.167 10 false *a
*a Seal Packing
*b 8.0 mm (0.315 in.)
*c Oil Passage


Apply seal packing to the specified areas shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

4 mm (0.157 in.)


NOTICE:
·

Do not allow seal packing to contact the oil passage of the camshaft bearing cap.

·

After applying seal packing, install the camshaft bearing caps within 3 minutes and tighten the bolts within 15 minutes.

·

Do not start the engine for at least 2 hours after installation.




e.
A352038

Install the No. 1 camshaft bearing cap, 3 No. 2 camshaft bearing caps and No. 3 camshaft bearing cap to their proper locations from the cylinder head sub-assembly.


f.
A352033N02
1.594,1.125 1.729,1.292 0.135,0.167 10 true 1 1.25,0.271 1.385,0.438 0.135,0.167 10 true 2 2.479,1.198 2.615,1.365 0.135,0.167 10 true 3 2.031,0.896 2.167,1.063 0.135,0.167 10 true 4 1.604,0.146 1.74,0.313 0.135,0.167 10 true 5 2.771,0.969 2.906,1.135 0.135,0.167 10 true 6 1.292,1.438 1.427,1.604 0.135,0.167 10 true 7 1.792,0.021 2,0.188 0.208,0.167 10 true 11 0.729,0.552 0.865,0.719 0.135,0.167 10 true 8 1.885,1.615 2.021,1.781 0.135,0.167 10 true 9 2.917,0.094 3.125,0.26 0.208,0.167 10 true 10 3.052,0.771 3.26,0.938 0.208,0.167 10 true 12 0.594,1.865 0.802,2.031 0.208,0.167 10 true 13 0.073,0.833 0.281,1 0.208,0.167 10 true 14 1.188,1.99 1.396,2.156 0.208,0.167 10 true 15

Apply a light coat of engine oil to the threads and under the heads of the camshaft bearing cap bolts.


g.

Install and uniformly tighten the 15 camshaft bearing cap bolts in several passes in the sequence shown in the illustration.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


h.
A352039N01
1.302,1.26 0.792,0.896 0.792,0.896 0.635,0.896 true 0.354,0.792 0.667,0.958 0.313,0.167 10 false SST

Install a new camshaft oil seal.

i.

Apply MP grease to the lip of a new camshaft oil seal.


ii.

Using SST and a hammer, tap in the camshaft oil seal until its surface is flush with the surfaces of the camshaft bearing cap and cylinder head sub-assembly.

SST
09608-06041  



Hide 13505 4.INSTALL NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

Hide 11322A 7.INSTALL NO. 1 TIMING BELT COVER

Hide 23670 8.INSTALL INJECTOR ASSEMBLY

Hide 11201 10.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 23770 11.INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 23704 12.INSTALL NO. 4 INJECTION PIPE SUB-ASSEMBLY

Hide 23701 13.INSTALL NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY

Hide 17940D 14.INSTALL INTERCOOLER ASSEMBLY

Hide 89424D 15.INSTALL INTAKE AIR TEMPERATURE SENSOR

Hide 89421C 16.INSTALL MANIFOLD ABSOLUTE PRESSURE SENSOR

Hide 12601B 17.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 16711 18.INSTALL FAN SHROUD

Hide 16571C 19.INSTALL NO. 1 RADIATOR HOSE

Hide 51410 26.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY