When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.
| Replaced Parts (A) | Pipes Requiring New Replacement |
|---|---|
·
Injector assembly (including shuffling the injector assemblies between the cylinders) ·
Common rail assembly ·
Cylinder head sub-assembly |
·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly ·
No. 3 injection pipe sub-assembly ·
No. 4 injection pipe sub-assembly |
·
Supply pump assembly ·
Common rail assembly ·
Cylinder block sub-assembly ·
Cylinder head sub-assembly ·
Cylinder head gasket ·
Timing Gear Case Assembly |
Fuel inlet pipe sub-assembly |
After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and fuel inlet pipe sub-assembly, clean them with a brush and compressed air.
11322A
1.REMOVE NO. 1 TIMING BELT COVER
13568
2.REMOVE TIMING BELT
13505
3.REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY
13408
4.REMOVE CRANKSHAFT PULLEY SUB-ASSEMBLY
17946
5.REMOVE NO. 2 INTERCOOLER SUPPORT BRACKET
Remove the 2 bolts and No. 2 intercooler support bracket from the cylinder head sub-assembly.
17945
6.REMOVE INTERCOOLER SUPPORT BRACKET
Remove the 2 bolts and intercooler support bracket from the cylinder head sub-assembly.
12229
7.REMOVE VENTILATION PIPE
17271
8.REMOVE NO. 1 TURBO INSULATOR
17167
9.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
16284
10.DISCONNECT NO. 1 TURBO WATER HOSE
17291
11.REMOVE TURBINE OUTLET ELBOW
17293
12.REMOVE TURBOCHARGER STAY
15407
13.DISCONNECT TURBO OIL INLET PIPE SUB-ASSEMBLY
14.REMOVE EXHAUST MANIFOLD WITH TURBOCHARGER
Remove the 8 nuts, 8 spacers, 8 collars and exhaust manifold with turbocharger shown in the illustration.
88440D
15.REMOVE NO. 2 IDLE PULLEY ASSEMBLY
27020
16.REMOVE GENERATOR ASSEMBLY
12511C
17.REMOVE GENERATOR BRACKET
Remove the bolt and generator bracket.
16620
18.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
Remove the 4 bolts and V-ribbed belt tensioner assembly from the cylinder block sub-assembly.
88431
19.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET
Remove the 4 bolts and No. 1 compressor mounting bracket from the cylinder block sub-assembly.
16321
20.REMOVE WATER INLET
16331A
21.REMOVE THERMOSTAT
16331
22.REMOVE WATER OUTLET
Remove the 2 bolts, water outlet and gasket from the cylinder head sub-assembly.
17118
23.REMOVE MANIFOLD STAY
26100G
24.REMOVE DIESEL THROTTLE BODY ASSEMBLY
25861C
25.REMOVE VACUUM SWITCHING VALVE BRACKET
17873A
26.REMOVE NO. 2 INTAKE AIR CONNECTOR BRACKET
17861
27.REMOVE INTAKE AIR CONNECTOR
15601
28.REMOVE OIL FILTER SUB-ASSEMBLY
23701
29.REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY
23704
30.REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY
23770
31.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY
15301
32.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
23804C
33.REMOVE FUEL INLET PIPE SUB-ASSEMBLY
23810A
34.REMOVE COMMON RAIL ASSEMBLY
22100
35.REMOVE FUEL SUPPLY PUMP ASSEMBLY
17111
36.REMOVE INTAKE MANIFOLD
25617A
37.REMOVE NO. 2 EGR HOLE COVER PLATE
Remove the 2 nuts and No. 2 EGR hole cover plate.
Remove the gasket.
19850
38.REMOVE GLOW PLUG ASSEMBLY
15701C
39.REMOVE OIL COOLER COVER SUB-ASSEMBLY
29300
40.REMOVE VACUUM PUMP ASSEMBLY
Remove the 2 nuts, vacuum pump assembly and 2 O-rings from the timing gear cover.
44320
41.REMOVE VANE PUMP ASSEMBLY
Remove the 2 nuts, vane pump assembly and O-ring from the timing gear case assembly.
42.REMOVE CRANKSHAFT POSITION SENSOR
43.REMOVE CAMSHAFT POSITION SENSOR
44.REMOVE ENGINE COOLANT TEMPERATURE SENSOR
12311
45.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH
| *a | LH Side |
| *b | RH Side |
Remove the 4 bolts and front No. 1 engine mounting bracket RH from the cylinder block sub-assembly.
12315
46.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH
Remove the 4 bolts and front No. 1 engine mounting bracket LH from th cylinder block sub-assembly.