Home › Engine / Hybrid System › 2GD-FTV ENGINE CONTROL › ECD SYSTEM(w/ DPF)
RM33J0E _51 Engine / Hybrid System _038437 2GD-FTV ENGINE CONTROL _0201524 ECD SYSTEM(w/ DPF) C

2GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P0420  Catalyst System Efficiency Below Threshold (Bank 1)  P2458  Diesel Particulate Filter Regeneration Duration  P2463  Diesel Particulate Filter Restriction - Soot Accumulation  


DESCRIPTION

DPF (Diesel Particulate Filter) is an emission control system which processes the particulate matter (PM) that is emitted from a diesel engine. The DPF catalyst has a porous ceramic structure which has a PM collecting function. The PM that is collected is continuously treated by oxidation due to catalytic action at high temperatures, however PM accumulation increases at low atalyst temperatures because the oxidation process slows down. The ECM performs PM forced regeneration so that the amount of accumulated PM does not exceed the threshold.

A357988E01
1.063,0.75 0.865,0.146 0.865,0.146 1,0.146 true 2.833,1.75 3.031,1.333 3.031,1.333 3.167,1.333 true 2.979,2.354 3.177,1.938 3.177,1.938 3.313,1.938 true 3.479,2.698 3.688,2.552 3.688,2.552 3.823,2.552 true 2.854,3.406 3.677,2.948 true 2.844,3.719 3.406,4.063 3.406,4.063 3.542,4.063 true 1.802,2.354 2.406,2.208 true 1.823,2.708 2.417,2.479 true 1.76,3.365 2.406,2.833 true 3.396,6.323 3.583,6.052 true 1.344,6.583 1.615,7.188 true 3.406,6.323 4.688,6.219 true 6.021,6.771 5.698,6.563 true 6.365,6.313 6.406,6.031 true 1.083,0.083 3.042,0.292 1.958,0.208 10 false Exhaust Fuel Addition Injector 0.052,0.75 0.625,1.135 0.573,0.385 10 false Exhaust Gas 3.24,1.26 5.875,1.49 2.635,0.229 10 false Exhaust Gas Temperature Sensor 3.375,1.865 5.865,2.25 2.49,0.385 10 false No. 2 Exhaust Gas Temperature Sensor 3.865,2.469 5.646,2.677 1.781,0.208 10 false Differential Pressure Sensor 3.76,2.823 5.76,3.219 2,0.396 10 false No. 3 Exhaust Gas Temperature Sensor 3.625,3.969 5.406,4.177 1.781,0.208 10 false Air Fuel Ratio Sensor 0.885,2.281 1.802,2.49 0.917,0.208 10 false DOC Catalyst 0.135,2.625 1.823,3.031 1.688,0.406 10 false Exhaust Manifold Converter Sub-assembly 0.917,3.271 1.833,3.479 0.917,0.208 10 false DPF Catalyst 0.406,4.677 2.292,4.906 1.885,0.229 10 false DPF (Diesel Particulate Filter): 3.417,4.677 4.99,4.906 1.573,0.229 10 false Monolithic Construction: 5.563,4.677 7.135,4.906 1.573,0.229 10 false Wall-Flow Type: 2.427,5.26 3.385,5.5 0.958,0.24 10 false PM, HC, CO 2.167,6.24 3.427,6.635 1.26,0.396 10 false Alternating Blocked Passages 1.698,7.104 4.135,7.344 2.438,0.24 10 false DPF (Diesel Particulate Filter) Catalyst 6.073,6.708 6.448,6.885 0.375,0.177 10 false PM 5.417,7.073 6.49,7.292 1.073,0.219 10 false Magnified View 6.115,6.292 6.792,6.5 0.677,0.208 10 false Gas Flow 4.771,5.281 5.469,5.51 0.698,0.229 10 false CO2, H2O 3.698,6.375 4.625,6.625 0.927,0.25 10 false Cross Section

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0420 Catalyst System Efficiency Below Threshold (Bank 1) During PM forced regeneration, DOC catalyst temperature does not increase sufficiently for 3 minutes.
(2 trip detection logic)
·

Exhaust manifold converter sub-assembly

·

Exhaust fuel addition injector assembly


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system


Comes on DTC stored
P2458 Diesel Particulate Filter Regeneration Duration When PM forced regeneration is manuallyperformed, PM forced regeneration does notfinish even after 60 minutes or more elapse.
(1 trip detection logic)
·

Exhaust manifold converter sub-assembly

·

Exhaust fuel addition injector assembly


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system


Comes on DTC stored
P2463 Diesel Particulate Filter Restriction - Soot Accumulation While driving, PM accumulation amount exceeds the limit.
(1 trip detection logic)
·

Exhaust Manifold Converter sub-assembly

·

Exhaust fuel addition injector assembly


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system


Comes on DTC stored

HINT:

PM forced regeneration may be prohibited due to a fail-safe operation that is performed when another DTC is stored (including engine output limitation).


Related Data List
DTC No. Data List
P0420
·

Exhaust Fuel Addition FB

·

Catalyst Differential Press


P2458
P2463

MONITOR DESCRIPTION

The ECM monitors the differential pressure between the upstream and downstream of the DPF catalyst and also monitors exhaust gas temperature to detect a malfunction in the exhaust manifold converter subassembly.

Abnormal DOC catalyst temperature increase:

The ECM monitors exhaust gas temperature increase while the exhaust fuel addition injector assembly adds fuel during PM forced regeneration. Exhaust gas temperature increases up to approximately 300 to 500°C (572 to 932°F) during PM forced regeneration. If the temperature does not increase even after a certain amount of time has elapsed, the ECM determines that the DOC catalyst is abnormal and illuminates the MIL.

A208470E10
3.229,1.875 3.323,2.031 3.323,2.031 3.49,2.031 false 5.229,1.875 5.302,1.625 5.302,1.625 5.417,1.625 false 5.135,1.458 5.083,1.281 5.083,1.281 4.958,1.281 false 5.313,1.427 5.396,0.875 5.396,0.875 5.531,0.875 false 0.083,0.083 2.052,0.417 1.969,0.333 10 false Catalyst Activation Malfunction: (DPF No Activate) 0.896,0.938 2.76,1.302 1.865,0.365 10 false PM Forced Regeneration (Activation of Fuel Addition) 1.115,1.781 2.781,1.958 1.667,0.177 10 false Exhaust Gas Temperature 3.521,1.958 4.938,2.198 1.417,0.24 10 false About 300°C (572°F) 5.458,1.563 6.104,1.729 0.646,0.167 10 false Abnormal 4.49,1.208 4.969,1.375 0.479,0.167 10 false Normal 3.323,0.813 3.635,1 0.313,0.188 10 false Off 5.135,0.385 5.375,0.542 0.24,0.156 10 false On 5.563,0.802 7.063,1.146 1.5,0.344 10 false More than About 500°C (932°F) 4.24,2.438 4.594,2.594 0.354,0.156 10 false Time


Catalytic converter Regeneration Duration:

When PM forced regeneration is manually performed, PM forced generation does not finish even after 60 minutes or more elapse, the ECM determines that there is problem with the DPF catalyst and illuminates the MIL.


Excessive PM accumulation:

The ECM monitors the PM Accumulation Ratio and when the accumulated PM volume in the DPF catalyst exceeds the limit, the ECM illuminates the MIL.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0420 PM forced regeneration
P2458
P2463

CAUTION / NOTICE / HINT

NOTICE:
·
·

After replacing an injector assembly, the ECM needs registration.

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>REGISTRATION



HINT:
·

If DTC P0420, P2458 or P2463 is stored, fail-safe controls engine power output and PM forced regeneration is prohibited. In this case, PM forced regeneration can be performed after disconnecting the EFI-MAIN NO. 1 fuse or battery terminal and waiting for 60 seconds or more before connecting it again.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ DTC OUTPUT (RECORD STORED DTC AND FREEZE FRAME DATA)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Record the stored DTC and freeze frame data.

Powertrain > Engine > Trouble Codes
50001 61

f.

Check Exhaust Fuel Addition FB and Catalyst Differential Press in the freeze frame data.

HINT:
·

When the Exhaust Fuel Addition FB value is 1.45 or more, it indicates a high possibility of insufficient temperature increase during PM regeneration control.

·

When the Catalyst Differential Press value is more than 0.47, it indicates a high possibility that DPF catalyst is clogged.




Result:
Proceed to
NEXT



NEXT

2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420, P2458 AND P2463)
2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420, P2458 AND P2463)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0420, P2458 or P2463 is output A
DTC P244B is output at the same time as P2463* B
Other relevant DTCs are output C


HINT:
·

*: When P244B is output at the same time as P2463, perform troubleshooting for P244B.

·

When DTC P1603, P1604 or P1608 is output in addition to P244C, perform troubleshooting for P1603, P1604 or P1608 first.





C

3.GO TO DTC CHART

B

A

4.CHECK FOR BLACK SMOKE
3.GO TO DTC CHART

Result:
Proceed to
NEXT



NEXT

4.CHECK FOR BLACK SMOKE
4.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it [A].


d.

Repeat the procedure [A] 10 times [B].


e.

Check for black smoke emission during the procedures [A] and [B].

OK:

Black smoke is emitted less than 5 times.


HINT:

Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.



Result:
Proceed to
OK
NG



NG

5.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

OK

6.CHECK FOR WHITE SMOKE (DURING PM FORCED REGENERATION)
5.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
a.

Even though it has been determined that the exhaust manifold converter sub-assembly (DPF catalyst) needs to be replaced, make sure to perform all diagnostic procedures for P0420, P2458 and P2463 before replacing it.

HINT:

This DTC is stored because an excessive amount of PM has accumulated and resulted in abnormal combustion. It is necessary to diagnose the cause of abnormal PM accumulation and repair the problem. Therefore, do not perform replacement at this time.



Result:
Proceed to
NEXT



NEXT

6.CHECK FOR WHITE SMOKE (DURING PM FORCED REGENERATION)
6.CHECK FOR WHITE SMOKE (DURING PM FORCED REGENERATION)
a.

Clear the DTC and Exhaust Fuel Addition FB value by disconnecting the cable from the negative (-) battery terminal or removing the EFI-MAIN NO. 1 fuse for 1 minute or more.

HINT:
·

The accumulated PM volume stored in the ECM cannot be initialized using the GTS.

·

To perform PM forced regeneration, it is necessary to perform initialization of the accumulated PM volume stored in the ECM.




b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

f.

Start the engine and warm it up until the engine coolanttemperature reaches 75°C (167°F) or higher.


g.

Maintain the maximum possible engine speed under no load for 10 seconds to blow out all soot from inside the exhaust pipe.

HINT:
·

If only a low engine speed is continuously maintained, soot may accumulate at the end of the catalyst.

·

When soot accumulates at the end of the catalyst, it may not be possible to perform PM forced regeneration control normally.





i.

Check if the temperature increases or abnormal white smoke occurs during PM forced regeneration.

Result:
Result Proceed to
No abnormal white smoke occurs but the temperature of exhaust gas temperature sensor B1S3 does not reach 450°C (842°F) or higher during PM forced regeneration A
Abnormal white smoke occurs and the temperature of exhaust gas temperature sensor B1S3 reaches 300°C (572°F) or higher during PM forced regeneration B
Except above* C


HINT:
·

When excessive white smoke occurs only during PM forced regeneration, uncombusted fuel passes through due to the deterioration of DPF catalyst is suspected.

·

When combustion control has a malfunction, deterioration or abnormality of driving performance can be felt despite PM forced regeneration.

·

If Exhaust Temperature B1S3 does not reach 450°C (842°F) or higher, the exhaust fuel addition injector assembly may be clogged.

·

*: Excessive accumulation of PM is caused by a worsening in combustion conditions and an increase in black smoke due to a malfunction in the control system.





A

7.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY

B

8.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

C

9.CHECK FUEL INJECTION SYSTEM
7.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
a.

Even though it has been determined that the exhaust fuel addition injector assembly needs to be replaced, make sure to perform all diagnostic procedures for P0420, P2458 and P2463 before replacing it.


Result:
Proceed to
NEXT



NEXT

9.CHECK FUEL INJECTION SYSTEM
8.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
a.

Even though it has been determined that the exhaust manifold converter sub-assembly (DPF catalyst) needs to be replaced, make sure to perform all diagnostic procedures for P0420, P2458 and P2463 before replacing it.

HINT:

This DTC is stored because an excessive amount of PM has accumulated and resulted in abnormal combustion. It is necessary to diagnose the cause of abnormal PM accumulation and repair the problem. Therefore, do not perform replacement at this time.



Result:
Proceed to
NEXT



NEXT

9.CHECK FUEL INJECTION SYSTEM
9.CHECK FUEL INJECTION SYSTEM

Result:
Proceed to
NEXT



NEXT

10.CHECK INTAKE / EXHAUST SYSTEM
10.CHECK INTAKE / EXHAUST SYSTEM

Result:
Proceed to
NEXT



NEXT

11.REPAIR OR REPLACE MALFUNCTIONING PARTS
11.REPAIR OR REPLACE MALFUNCTIONING PARTS
HINT:

Replace the following items only when it has been determined necessary based on diagnosis for DTC P0420, P2458 and P2463.


a.

Replace the exhaust manifold converter sub-assembly (DPF catalyst).

Click hereEngine / Hybrid System>2GD-FTV EMISSION CONTROL>MONOLITHIC CONVERTER(w/ DPF)>REMOVAL

NOTICE:

Perform Initialization procedure for "DPF catalyst record clear" and "DPF Deterioration Record Clear"

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>INITIALIZATION



b.

Replace the exhaust fuel addition injector assembly.

Click hereEngine / Hybrid System>2GD-FTV EMISSION CONTROL>EXHAUST FUEL ADDITION INJECTOR>REMOVAL


c.

Repair or replace the malfunctioning part confirmed in the diagnosis of the fuel injection system and intake/exhaust system.


Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

d.

Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).



Result:
Proceed to
NEXT



NEXT

END