Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION ASSEMBLY › from 2015.11
RM33J0E _52 Drivetrain _038463 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0192017 AUTOMATIC TRANSMISSION ASSEMBLY A

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 32000 1.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C324533C01
1.146,0.948 0.896,0.188 0.896,0.188 0.729,0.188 true 1.156,2.427 0.927,3.073 0.927,3.073 0.76,3.073 true 2.667,1.271 2.979,1.427 0.313,0.156 10 false *a 3.063,1.75 3.333,1.938 0.271,0.188 10 false *b 0.542,0.094 0.854,0.25 0.313,0.156 10 false *a 0.583,2.99 0.854,3.177 0.271,0.188 10 false *b 2.677,0.552 2.99,0.708 0.313,0.156 10 false A
*a Engine Surface
*b Drive Plate Surface


Using a vernier caliper, measure the dimension (A) between the automatic transmission assembly contact surface of the engine assembly and torque converter assembly contact surface of the drive plate and ring gear sub-assembly.


b.
C218122C01
0.417,0.385 1.271,0.167 true 0.667,0.594 1.271,0.167 true 1.323,0.073 1.635,0.271 0.313,0.198 10 false *a
*a Matchmark


Align the matchmark on the automatic transmission case sub-assembly with the one on the torque converter assembly and engage the splines of the input shaft with the turbine runner splines.

NOTICE:

Install the torque converter assembly to the input shaft while keeping it horizontal.



c.
C324402C01
1.833,1.917 2.802,1.156 true 1.833,1.917 2.792,0.906 true 1.75,1.948 2,2.104 0.25,0.156 10 false *1
*1 Front Oil Pump Oil Seal


Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.

NOTICE:
·

Do not damage the front oil pump oil seal.

·

Install the torque converter assembly to the input shaft while keeping it horizontal.




d.
C324403C01
1.792,1.958 2.792,0.917 true 1.781,1.958 2.792,1.167 true 1.656,1.969 1.969,2.167 0.313,0.198 10 false *1
*1 Front Oil Pump Oil Seal


Turn the torque converter assembly to engage the key of the oil pump drive gear with the slot on the torque converter assembly.

NOTICE:
·

Do not push the torque converter assembly excessively when rotating it.

·

Do not damage the front oil pump oil seal.

·

Install the torque converter assembly to the input shaft while keeping it horizontal.




e.
C193531N02
2.406,0.25 2.604,0.458 0.198,0.208 10 false B

Using a vernier caliper and straightedge, measure the dimension (B) shown in the illustration and check that the dimension (B) is more than the dimension (A), which was measured in the previous step.

Standard:

B = A + 1.00 mm (0.0394 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the automatic transmission assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.




Hide 36478A 2.INSTALL TRANSMISSION BREATHER BRACKET

a.

Install the transmission breather bracket with the bolt.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


b.
C324400

Attach the clamp to connect the automatic transmission breather hose to the transfer breather bracket.


Hide 3.INSTALL WIRE HARNESS CLAMP BRACKET

a.
C324364C01
0.604,2.323 0.76,2.5 0.156,0.177 10 true *a 2.552,0.146 2.708,0.323 0.156,0.177 10 true *b 0.948,0.531 1.104,0.708 0.156,0.177 10 true *a
*a Bolt A
*b Bolt B


Install 3 wire harness clamp brackets with the 3 bolts.

Torque:
for bolt A : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
for bolt B : 12.6 N*m (128 kgf*cm, 9 ft.*lbf)


Hide 36100 4.INSTALL TRANSFER ASSEMBLY

Hide 5.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY

a.
C187504C01
2.969,1.083 1.917,1.083 true 0.958,0.99 1.188,1.198 0.229,0.208 10 false *2 3.031,0.99 3.271,1.188 0.24,0.198 10 false *1
*1 Torque Converter Centerpiece
*2 Crankshaft


Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter centerpiece.

Clutch spline grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum grease amount:

Approximately 1.0 g (0.0353 oz)



b.
C324052

Confirm that the 2 knock pins are installed on the engine assembly and are not damaged.


c.

Install the automatic transmission assembly to the engine with the 5 bolts.

Torque:
71 N*m (724 kgf*cm, 52 ft.*lbf)

NOTICE:
·

Do not use excessive force when installing the automatic transmission assembly.

·

Check that the torque converter assembly rotates.

·

Make sure that the wire harness or other similar items are not pinched between the contact surfaces.

·

Make sure that the cooling fan and fan shroud do not contact the engine assembly when tilting the automatic transmission assembly.




Hide 82121 6.CONNECT ENGINE WIRE

a.

Attach the 7 wire harness clamps and connect the engine wire to the automatic transmission assembly and transfer assembly with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Connect the 5 connectors.

HINT:

Push up the lever until the claw of the transmission wire connector makes a connection sound.



c.

Attach the 5 clamps and connect the transfer breather hose sub-assembly to the automatic transmission assembly.


Hide 12371A 7.INSTALL REAR ENGINE MOUNTING INSULATOR

a.

Install the rear engine mounting insulator to the automatic transmission assembly with the 4 bolts.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


Hide 51204 8.INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.

Connect the ends of the No. 3 frame crossmember sub-assembly to the body with the 4 bolts and 4 nuts.

Torque:
57 N*m (581 kgf*cm, 42 ft.*lbf)

HINT:

Hold the bolts while tightening the nuts.



b.

Connect the No. 3 frame crossmember sub-assembly to the rear engine mounting insulator with the 4 bolts.

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)


Hide 9.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.

Turn the crankshaft to gain access to the installation locations of the 6 torque converter assembly setting bolts and install each bolt through the hole of the flywheel while holding the crankshaft pulley bolt with a wrench.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)

NOTICE:

Install the black colored bolt first, and then the silver colored 5 bolts.



Hide 33118B 10.INSTALL STIFFENER PLATE

a.

Install the No. 2 end plate.


b.

Install the No. 4 cylinder block insulator.


c.

Install the stiffener plate LH to the engine and automatic transmission assembly with the 4 bolts.

Torque:
71 N*m (724 kgf*cm, 52 ft.*lbf)


d.

Install the stiffener plate RH (with oil cooler tube clamp) to the engine and automatic transmission assembly with the 4 bolts.

Torque:
71 N*m (724 kgf*cm, 52 ft.*lbf)


Hide 82284 11.CONNECT GROUND WIRE

a.
C324361

Connect the ground wire to the transfer assembly with the bolt as shown in the illustration.

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)

HINT:

Make contact with the terminal stopper.



Hide 32921 12.CONNECT OIL COOLER TUBE

a.
C324045N01
0.188,0.938 0.344,1.135 0.156,0.198 10 true A 1.698,0.969 1.854,1.167 0.156,0.198 10 true B 1.51,1.781 1.667,1.979 0.156,0.198 10 true B 3.156,1.635 3.313,1.833 0.156,0.198 10 true A

Install the 3 clamps to the automatic transmission assembly and engine assembly with the 4 bolts.

Torque:
for bolt A (M8 bolt) : 13.5 N*m (138 kgf*cm, 10 ft.*lbf)
for bolt B (M12 bolt) : 71 N*m (724 kgf*cm, 52 ft.*lbf)

HINT:

It is not necessary to remove the clamp unless they are being replaced.



b.

Connect the end of the inlet oil cooler tube to the automatic transmission assembly by hand.


c.

Connect the end of the outlet oil cooler tube to the automatic transmission assembly by hand.


d.

Install the 3 oil cooler tube clamps with the 3 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


e.
C324368C01
2.156,0.365 2.469,0.563 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length


Using a 17 mm union nut wrench, tighten the oil cooler tube inlet and oil cooler tube outlet.

Specified tightening torque:

34.3 N*m (350 kgf*cm, 25 ft.*lbf)


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 300 mm (11.8 in.)): 31.2 N*m (318 kgf*cm, 23 ft.*lbf)




Hide 33823 13.INSTALL TRANSMISSION CONTROL CABLE BRACKET

a.

Install the transmission control cable bracket with the 2 bolts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 33820B 14.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Move the shift lever to N.


b.
C236140N02
1.375,0.104 1.604,0.292 0.229,0.188 10 false N 1.771,0.427 2.01,0.635 0.24,0.208 10 false R 2.292,0.323 2.448,0.5 0.156,0.177 10 false P

Turn the transmission control shaft lever clockwise until it stops, and then turn it counterclockwise 2 notches to set it to the N position.


c.

Connect the transmission control cable assembly to the transmission control cable bracket with a new clip, and then connect the cable end to the transmission control shaft lever LH with the nut.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 17410 15.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 41110F 18.INSTALL FRONT DIFFERENTIAL CARRIER ASSEMBLY

Hide 21.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 25.INSPECT FOR OIL LEAK

a.

Start the engine. Make sure that there are no oil leaks from the areas that were worked on.


Hide 26. RESET MEMORY

NOTICE:

If automatic transmission parts have been replaced, refer to the Parts Replacement Compensation Table to determine if any additional operations are necessary.

Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION