Home › Drivetrain › AC60F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION ASSEMBLY(for 1GD-FTV) › from 2015.11
RM33J0E _52 Drivetrain _038466 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0196294 AUTOMATIC TRANSMISSION ASSEMBLY(for 1GD-FTV) A

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY(for 1GD-FTV)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the automatic transmission assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
·

Automatic transmission assembly

·

Automatic transmission fluid


·

Reset memory

·

ATF thermal degradation estimate reset


·

Large shift shock

·

The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly


(Click here)

CAUTION:
·
A350542

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.

·
C313282C04
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a Object Exceeding Weight Limit of Transmission Jack


The automatic transmission assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 41110F 3.REMOVE FRONT DIFFERENTIAL CARRIER ASSEMBLY

Hide 37100 6.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Hide 17410 8.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 33820B 9.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C323981

Remove the clip and nut and disconnect the transmission control cable assembly from the transmission control shaft lever LH and transmission control cable bracket.


Hide 10.DISCONNECT OIL COOLER TUBE

a.
C324534

Disconnect the 2 oil cooler tubes from the automatic transmission assembly.

HINT:

Use a container to catch any ATF which flows out of the 2 oil cooler tubes and automatic transmission assembly.



b.

Remove the 3 bolts and disconnect the 2 oil cooler tubes from the 3 oil cooler tube clamps.

C326321


c.

Remove the 4 bolts and 3 oil cooler tube clamps from the automatic transmission assembly and engine assembly.

HINT:

It is not necessary to remove the oil cooler tube clamps unless they are being replaced.



Hide 82284 11.DISCONNECT GROUND WIRE

a.
C324544

Remove the bolt and disconnect the ground wire from the automatic transmission assembly.


Hide 35979B 12.REMOVE TRANSMISSION INSULATOR RH

Hide 13.SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

a.
C324541

Support the automatic transmission assembly with a transmission jack.

NOTICE:
·

In order to protect the automatic transmission oil pan sub-assembly, place attachments on the transmission jack.

·

Make sure that the attachments and the automatic transmission oil pan sub-assembly are centered on the transmission jack.

·

To prevent the automatic transmission oil pan sub-assembly from deforming, do not place any attachments under the automatic transmission oil pan sub-assembly of the automatic transmission assembly.

·

Secure the automatic transmission assembly to the transmission jack using a belt, etc. to prevent it from falling.




Hide 14.REMOVE STIFFENER PLATE

a.

Remove the No. 4 cylinder block insulator from the engine assembly.


b.

Remove the 4 bolts and stiffener plate LH from the automatic transmission assembly and engine assembly.

C324514


c.

Remove the 4 bolts, stiffener plate RH (with clamp) and No. 2 end plate from the automatic transmission assembly and engine assembly.


Hide 15.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.
C324515

Turn the crankshaft to gain access to the locations of the 6 drive plate and torque converter assembly setting bolts and remove each bolt while holding the crankshaft pulley bolt with a wrench.


Hide 51204 16.REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.
C326315

Remove the 4 bolts and disconnect the No. 3 frame crossmember sub-assembly from the rear engine mounting insulator.


b.

Remove the 4 bolts, 4 nuts and No. 3 frame crossmember sub-assembly from the vehicle body.


Hide 12371A 17.REMOVE REAR ENGINE MOUNTING INSULATOR

HINT:

It is not necessary to remove the rear engine mounting insulator unless it is being replaced.


a.
C326317

Remove the 4 bolts and rear engine mounting insulator from the automatic transmission assembly.


Hide 18.DISCONNECT WIRE HARNESS

a.

Tilt down the automatic transmission assembly.

NOTICE:

Make sure that the cooling fan and fan shroud do not contact the engine assembly when tilting the automatic transmission assembly.



b.
C324542

Disconnect the transfer breather hose sub-assembly from the wire harness and clamp of the transmission breather bracket.


c.

Disconnect the 9 wire harness clamps.

C324547


d.

Disconnect the park/neutral position switch connector, transmission wire connector, 2 transmission revolution sensor connectors and transfer connector.

HINT:

Detach the claw, press down the lever, and then disconnect the transmission wire connector.



e.

Remove the 2 bolts and disconnect the wire harness from the automatic transmission assembly.


Hide 19.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

a.
C324540

Remove the 5 bolts and automatic transmission assembly from the engine assembly.

NOTICE:

To prevent damage to the 2 knock pins, do not pry between the automatic transmission assembly and engine assembly.



Hide 36478A 20.REMOVE TRANSMISSION BREATHER BRACKET

HINT:

It is not necessary to remove the transmission breather bracket unless it is being replaced.


a.
C332143

Disconnect the 3 breather plug hoses from the clamp.


b.
C324543

Remove the 2 clamps from the transmission breather bracket.


c.

Remove the bolt and transmission breather bracket from the automatic transmission assembly.


Hide 22.REMOVE WIRE HARNESS CLAMP BRACKET

HINT:

It is not necessary to remove the wire harness clamp brackets unless they are being replaced.


a.

Remove the 4 bolts and 3 wire harness clamp brackets from the automatic transmission assembly.

C324549


Hide 33823 23.REMOVE TRANSMISSION CONTROL CABLE BRACKET

HINT:

It is not necessary to remove the transmission control cable bracket unless it is being replaced.


a.
C324529

Remove the 2 bolts and transmission control cable bracket from the automatic transmission assembly.


Hide 24.REMOVE TORQUE CONVERTER ASSEMBLY

a.
C324532C01
1.729,0.438 1.125,0.156 1.125,0.156 1.719,0.219 true 0.938,0.042 1.25,0.24 0.313,0.198 10 false *a
*a Matchmark


Put matchmarks on the automatic transmission assembly and the torque converter assembly.


b.

Remove the torque converter assembly from the automatic transmission assembly.

NOTICE:

Remove the torque converter assembly from the input shaft horizontally.