To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.
| *a | Object Exceeding Weight Limit of Transmission Jack |
The manual transmission assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
28800
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
33504F
3.REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY
Remove the shift lever knob sub-assembly from the shift lever.
58810J
4.REMOVE CONSOLE BOX ASSEMBLY (w/ Console Box Lid)
58811A
5.REMOVE FRONT CONSOLE BOX (w/o Console Box Lid)
58280A
6.REMOVE SHIFT LEVER BOOT ASSEMBLY
Remove the 6 screws, 4 clips and shift lever boot assembly.
33530F
7.REMOVE FLOOR SHIFT SHIFT LEVER ASSEMBLY
Detach the shift lever cap boot from the manual transmission.
Cover the shift lever cap with a cloth.
| *1 | Shift Lever Cap |
| *a | Press Down |
| *b | Counterclockwise |
| *c | Pull Out |
While pressing down on the shift lever cap, turn it counterclockwise, and then pull to remove the shift lever.
33548F
8.REMOVE NO. 1 FLOOR SHIFT BUSH
Remove the No. 1 floor shift bush from the floor shift shift lever assembly.
9.DRAIN MANUAL TRANSMISSION OIL
51410
10.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY
51442
11.REMOVE NO. 2 ENGINE UNDER COVER
51561D
12.REMOVE PROPELLER SHAFT GUARD
Remove the propeller shaft guard with the 2 bolts.
17410
13.INSTALL FRONT EXHAUST PIPE ASSEMBLY (for 1GD-FTV)
17410
14.INSTALL FRONT EXHAUST PIPE ASSEMBLY (for 2GD-FTV)
17410
15.INSTALL FRONT EXHAUST PIPE ASSEMBLY (for 1KD-FTV)
17410
16.REMOVE FRONT EXHAUST PIPE ASSEMBLY (for 2KD-FTV)
28100
17.REMOVE STARTER ASSEMBLY (for 1GD-FTV)
for 2.0 kW Type:
Click hereEngine / Hybrid System>1GD-FTV STARTING>STARTER(for 2.0 kW Type)>REMOVAL
for 2.2 kW Type:
Click hereEngine / Hybrid System>1GD-FTV STARTING>STARTER(for 2.2 kW Type)>REMOVAL
for BOSCH Made:
Click hereEngine / Hybrid System>1GD-FTV STARTING>STARTER(for BOSCH Made)>REMOVAL
28100
18.REMOVE STARTER ASSEMBLY (for 2GD-FTV)
for 2.0 kW Type:
Click hereEngine / Hybrid System>2GD-FTV STARTING>STARTER(for 2.0 kW Type)>REMOVAL
for 2.2 kW Type:
Click hereEngine / Hybrid System>2GD-FTV STARTING>STARTER(for 2.2 kW Type)>REMOVAL
for BOSCH Made:
Click hereEngine / Hybrid System>2GD-FTV STARTING>STARTER(for BOSCH Made)>REMOVAL
28100
19.REMOVE STARTER ASSEMBLY (for 1KD-FTV)
for 2.0 kW Type:
Click hereEngine / Hybrid System>1KD-FTV STARTING>STARTER(for 2.0 kW Type)>REMOVAL
for 2.2 kW Type:
Click hereEngine / Hybrid System>1KD-FTV STARTING>STARTER(for 2.2 kW Type)>REMOVAL
for BOSCH Made:
Click hereEngine / Hybrid System>1KD-FTV STARTING>STARTER(for BOSCH Made)>REMOVAL
28100
20.REMOVE STARTER ASSEMBLY (for 2KD-FTV)
for 2.0 kW Type:
Click hereEngine / Hybrid System>2KD-FTV STARTING>STARTER(for 2.0 kW Type)>REMOVAL
for 2.2 kW Type:
Click hereEngine / Hybrid System>2KD-FTV STARTING>STARTER(for 2.2 kW Type)>REMOVAL
for BOSCH Made:
Click hereEngine / Hybrid System>2KD-FTV STARTING>STARTER(for BOSCH Made)>REMOVAL
12584
21.REMOVE NO. 4 CYLINDER BLOCK INSULATOR
Remove the No. 4 cylinder block insulator.
33119
22.REMOVE STIFFENER PLATE LH
Remove the 4 bolts and stiffener plate LH.
33118
23.REMOVE STIFFENER PLATE RH
Remove the 4 bolts and stiffener plate RH.
37100
24.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY
for TASA Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for TASA Made)>REMOVAL
for TMT Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for TMT Made)>REMOVAL
41110F
25.REMOVE FRONT DIFFERENTIAL CARRIER ASSEMBLY
26.DISCONNECT GROUND CABLE
Remove the bolt and disconnect the ground cable.
27.SUPPORT MANUAL TRANSMISSION ASSEMBLY
Support the manual transmission with a transmission jack.
Make sure the high transmission jack attachment is centered on the safety stand.
Secure the part with a rope, attachment, etc.
51204
28.REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY
Remove the 4 bolts from the No. 3 frame crossmember sub-assembly.
Remove the 4 nuts, 4 bolts and No. 3 frame crossmember sub-assembly.
12371A
29.REMOVE REAR ENGINE MOUNTING INSULATOR
Remove the 4 bolts and rear engine mounting insulator from the manual transmission assembly.
30.DISCONNECT WIRE HARNESS
w/ Intelligent Manual Transmission Switch:
Detach the 7 wire harness clamps.
Remove the bolt.
Disconnect the 3 connectors and wire harness.
w/o Intelligent Manual Transmission Switch:
Detach the 5 wire harness clamps.
Remove the bolt.
Disconnect the 2 connectors and wire harness.
31.REMOVE MANUAL TRANSMISSION ASSEMBLY
Remove the 5 bolts and manual transmission assembly.
As the manual transmission assembly is very heavy, be sure to support it securely.
33019C
32.REMOVE TRANSMISSION BREATHER SUB-ASSEMBLY
Detach the 4 breather hose clamps and bracket.
Remove the transmission breather sub-assembly from the control shift lever retainer assembly.
Remove the 2 bolts and 2 brackets.
33.REMOVE WIRING HARNESS CLAMP BRACKET
w/ Intelligent Manual Transmission Switch:
Remove the 8 bolts and 7 wiring harness clamp brackets.
w/o Intelligent Manual Transmission Switch:
Remove the 7 bolts and 6 wiring harness clamp brackets.
34.REMOVE TRANSFER ASSEMBLY