Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2015.11
RM33J0E _56 Audio / Visual / Telematics _044808 NAVIGATION / MULTI INFO DISPLAY _0219999 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Steering Pad Switch Circuit  


DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the navigation receiver assembly.

If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.

If there is a short in the circuit, the same condition as when a switch is continuously depressed occurs.

Therefore, the navigation receiver assembly cannot be operated using the steering pad switch assembly, and also the navigation receiver assembly itself cannot function.

WIRING DIAGRAM

E341245E03
0.531,0.99 1.146,1.188 0.615,0.198 10 false VOL- 0.438,2.115 1.052,2.313 0.615,0.198 10 false VOICE 1.302,0.979 1.917,1.177 0.615,0.198 10 false VOL+ 1.917,0.979 2.531,1.177 0.615,0.198 10 false SEEK- 2.583,1 3.198,1.198 0.615,0.198 10 false SEEK+ 1.177,2.042 1.656,2.385 0.479,0.344 10 false OFF HOOK 2.563,2.125 3.177,2.323 0.615,0.198 10 false MODE 1.552,3.115 4.146,3.375 2.594,0.26 10 false Steering Pad Switch LH Side 1.917,2.031 2.396,2.375 0.479,0.344 10 false ON HOOK 1.458,3.656 4.052,3.917 2.594,0.26 10 false Steering Pad Switch Assembly 0.323,4.875 2.917,5.135 2.594,0.26 10 false *1: w/ VSC 0.344,5.25 2.938,5.51 2.594,0.26 10 false *2: w/o VSC 4.521,0.438 5.135,0.635 0.615,0.198 10 false z2 4.51,1.552 5.125,1.75 0.615,0.198 10 false z2 4.521,2.656 5.135,2.854 0.615,0.198 10 false z2 4.51,0.24 5.125,0.438 0.615,0.198 10 false 11 4.542,1.365 5.156,1.563 0.615,0.198 10 false 8 4.5,2.469 5.115,2.667 0.615,0.198 10 false 10 4.865,0.323 5.479,0.521 0.615,0.198 10 false AU1 4.854,1.448 5.469,1.646 0.615,0.198 10 false EAU 4.875,2.552 5.49,2.75 0.615,0.198 10 false AU2 4.333,3.646 5.885,3.979 1.552,0.333 10 false Spiral with Sensor Cable Sub-assembly*1 4.198,4.24 6.125,4.542 1.927,0.302 10 false Spiral Cable Sub-assembly*2 5.354,2.667 5.969,2.865 0.615,0.198 10 false G4 5.354,0.448 5.969,0.646 0.615,0.198 10 false G4 5.354,1.563 5.969,1.76 0.615,0.198 10 false G4 5.417,0.25 6.031,0.448 0.615,0.198 10 false 6 5.406,1.354 6.021,1.552 0.615,0.198 10 false 3 5.406,2.469 6.021,2.667 0.615,0.198 10 false 5 5.927,0.333 6.542,0.531 0.615,0.198 10 false 21 5.958,1.427 6.573,1.625 0.615,0.198 10 false 23 5.958,2.563 6.573,2.76 0.615,0.198 10 false 22 6.24,0.448 6.854,0.646 0.615,0.198 10 false SW1 6.25,1.563 6.865,1.76 0.615,0.198 10 false SWG 6.219,2.667 6.833,2.865 0.615,0.198 10 false SW2 5.906,4.719 6.521,4.917 0.615,0.198 10 false G116 5.917,4.865 7.156,5.24 1.24,0.375 10 false Navigation Receiver Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

for Type A: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION

for Type B: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION

·

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK VEHICLE CONDITION

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

2.CHECK VEHICLE CONDITION
a.

Check the vehicle condition.


Result:
Result Proceed to
w/ VSC A
w/o VSC B



A

3.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

B

5.INSPECT SPIRAL CABLE SUB-ASSEMBLY
3.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY
a.

Remove the spiral with sensor cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral with sensor cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY)

NG

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY)
a.

Disconnect the G116 navigation receiver assembly connector.


b.

Disconnect the G4 spiral with sensor cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G116-21 (SW1) - G4-6 (AU1) Always Below 1 Ω
G116-23 (SWG) - G4-3 (EAU) Always Below 1 Ω
G116-22 (SW2) - G4-5 (AU2) Always Below 1 Ω
G116-23 (SWG) - Body ground Always Below 1 Ω
G116-21 (SW1) - Body ground Always 10 kΩ or higher
G116-22 (SW2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)
a.

Disconnect the G116 navigation receiver assembly connector.


b.

Disconnect the G4 spiral cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G116-21 (SW1) - G4-6 (AU1) Always Below 1 Ω
G116-23 (SWG) - G4-3 (EAU) Always Below 1 Ω
G116-22 (SW2) - G4-5 (AU2) Always Below 1 Ω
G116-23 (SWG) - Body ground Always Below 1 Ω
G116-21 (SW1) - Body ground Always 10 kΩ or higher
G116-22 (SW2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR