Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › from 2015.11
RM33J0E _51 Engine / Hybrid System _038462 CRUISE CONTROL _0181542 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  Clutch Switch Circuit  


DESCRIPTION

While depressing the clutch pedal, the clutch switch sends a signal to terminal D of the ECM. The ECM cancels cruise control when terminal D receives the signal.

WIRING DIAGRAM

C323211E06
1.417,0.531 3.271,0.729 1.854,0.198 10 false from IG1 NO. 1 Relay*1 1.344,1.833 2.083,2.135 0.74,0.302 10 false IG1 NO. 4 2.75,2.281 4.427,2.479 1.677,0.198 10 false Clutch Switch Assembly 6.281,2.833 6.74,3.031 0.458,0.198 10 false ECM 6.083,1.594 6.24,1.792 0.156,0.198 10 false D 2.75,1.479 2.906,1.677 0.156,0.198 10 false 1 4.146,1.479 4.302,1.677 0.156,0.198 10 false 2 2.688,2.104 3,2.302 0.313,0.198 10 false B1 5.781,1.479 6.094,1.677 0.313,0.198 10 false 14 6.031,2.719 6.49,2.917 0.458,0.198 10 false C38 1.417,0.865 4.25,1.083 2.833,0.219 10 false from Ignition or Starter Switch Assembly*2 0.167,2.948 2.844,3.271 2.677,0.323 10 false *1: w/ Smart Entry and Start System 0.167,3.271 2.844,3.594 2.677,0.323 10 false *2: w/o Smart Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT CLUTCH SWITCH ASSEMBLY
a.

Remove the clutch switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>REMOVAL


b.

Inspect the clutch switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CLUTCH SWITCH ASSEMBLY - BATTERY)

NG

REPLACE CLUTCH SWITCH ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (CLUTCH SWITCH ASSEMBLY - BATTERY)
a.
C326224C05
1.458,0.25 1.917,0.552 0.458,0.302 1.615,0.323 1.927,0.521 0.313,0.198 10 false B1 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Clutch Switch Assembly)


Disconnect the clutch switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B1-1 - Body ground Ignition Switch ON 11 to 14 V
B1-1 - Body ground Ignition Switch off Below 1 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CLUTCH SWITCH ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CLUTCH SWITCH ASSEMBLY - ECM)
a.

Disconnect the B1 clutch switch assembly connector.


b.

Disconnect the C57 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B1-2 - C57-14 (D) Always Below 1 Ω
B1-2 or C57-14 (D) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR