Home › Engine / Hybrid System › 1GD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART) › from 2015.11
RM33J0E _51 Engine / Hybrid System _038420 1GD-FTV ENGINE CONTROL _0243396 ECD SYSTEM(for i-ART) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  P0201  Injector Circuit / Open - (Cylinder 1)  P0202  Injector Circuit / Open - (Cylinder 2)  P0203  Injector Circuit / Open - (Cylinder 3)  P0204  Injector Circuit / Open - (Cylinder 4)  P062D  No. 1 Fuel Injector Driver Circuit Performance  


DESCRIPTION

The injector assemblies are installed in the cylinder head and inject fuel into the cylinders based on the signals from the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0201 Injector Circuit / Open - (Cylinder 1) Open or short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds).
(1 trip detection logic)
·

Open or short in No. 1 injector assembly circuit

·

No. 1 Injector assembly

·

ECM


Comes on DTC stored
P0202 Injector Circuit / Open - (Cylinder 2) Open or short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds).
(1 trip detection logic)
·

Open or short in No. 2 injector assembly circuit

·

No. 2 Injector assembly

·

ECM


Comes on DTC stored
P0203 Injector Circuit / Open - (Cylinder 3) Open or short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds).
(1 trip detection logic)
·

Open or short in No. 3 injector assembly circuit

·

No. 3 Injector assembly

·

ECM


Comes on DTC stored
P0204 Injector Circuit / Open - (Cylinder 4) Open or short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds).
(1 trip detection logic)
·

Open or short in No. 4 injector assembly circuit

·

No. 4 Injector assembly

·

ECM


Comes on DTC stored
P062D No. 1 Fuel Injector Driver Circuit Performance ECM internal error
(1 trip detection logic)
ECM Comes on DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0201
P0202
P0203
P0204
P062D
Idling for 5 seconds or more

WIRING DIAGRAM

A348540E06
6.333,8.302 6.74,8.469 0.406,0.167 10 false ECM 5.792,0.521 6.094,0.677 0.302,0.156 10 false C57 5.792,0.927 6.094,1.083 0.302,0.156 10 false C57 5.802,1.594 6.104,1.75 0.302,0.156 10 false C57 5.802,2.01 6.104,2.167 0.302,0.156 10 false C57 5.802,2.677 6.104,2.833 0.302,0.156 10 false C58 5.802,3.094 6.104,3.25 0.302,0.156 10 false C58 5.802,3.76 6.104,3.917 0.302,0.156 10 false C58 5.802,4.188 6.104,4.344 0.302,0.156 10 false C58 5.802,5.094 6.104,5.25 0.302,0.156 10 false C59 5.813,4.729 6.115,4.885 0.302,0.156 10 false C59 6.146,6.208 6.385,6.375 0.24,0.167 10 false +B 6.156,5.094 6.531,5.26 0.375,0.167 10 false +BD2 5.802,6.219 6.104,6.375 0.302,0.156 10 false G86 5.802,6.583 6.104,6.74 0.302,0.156 10 false G86 5.781,6.938 6.083,7.094 0.302,0.156 10 false G86 5.792,7.292 6.094,7.448 0.302,0.156 10 false G85 2.427,1.323 3.938,1.51 1.51,0.188 10 false No. 1 Injector Assembly 2.427,2.271 2.917,2.469 0.49,0.198 10 false C127 2.427,2.406 3.938,2.594 1.51,0.188 10 false No. 2 Injector Assembly 2.427,3.344 2.875,3.531 0.448,0.188 10 false C128 2.438,3.469 3.948,3.656 1.51,0.188 10 false No. 3 Injector Assembly 2.406,4.448 2.885,4.635 0.479,0.188 10 false C129 2.417,4.583 3.927,4.771 1.51,0.188 10 false No. 4 Injector Assembly 2.302,1.052 2.448,1.208 0.146,0.156 10 false 6 3.375,1.042 3.521,1.198 0.146,0.156 10 false 3 2.417,1.188 2.833,1.344 0.417,0.156 10 false C126 2.313,2.135 2.458,2.292 0.146,0.156 10 false 6 3.375,2.135 3.521,2.292 0.146,0.156 10 false 3 2.313,3.208 2.458,3.365 0.146,0.156 10 false 6 3.375,3.208 3.521,3.365 0.146,0.156 10 false 3 3.385,4.302 3.531,4.458 0.146,0.156 10 false 3 2.302,4.292 2.448,4.448 0.146,0.156 10 false 6 5.885,0.75 6.031,0.906 0.146,0.156 10 false 7 5.885,0.344 6.031,0.5 0.146,0.156 10 false 6 5.885,1.417 6.031,1.573 0.146,0.156 10 false 1 5.896,1.833 6.042,1.99 0.146,0.156 10 false 2 5.885,2.5 6.031,2.656 0.146,0.156 10 false 7 5.885,3.583 6.031,3.74 0.146,0.156 10 false 5 5.885,2.917 6.031,3.073 0.146,0.156 10 false 6 5.885,4.01 6.031,4.167 0.146,0.156 10 false 4 5.885,4.917 6.031,5.073 0.146,0.156 10 false 4 5.885,4.542 6.031,4.698 0.146,0.156 10 false 5 3.24,5.75 3.563,5.917 0.323,0.167 10 false EDU 3.75,5.219 3.896,5.375 0.146,0.156 10 false 5 2.969,5.219 3.115,5.375 0.146,0.156 10 false 3 2.979,5.563 3.125,5.719 0.146,0.156 10 false 2 3.74,5.563 3.885,5.719 0.146,0.156 10 false 1 1.083,5.25 1.406,5.417 0.323,0.167 10 false EDU 1.042,4.99 1.188,5.146 0.146,0.156 10 false 1 1.313,4.99 1.458,5.146 0.146,0.156 10 false 2 2.635,8.021 4.667,8.198 2.031,0.177 10 false Instrument Panel Junction Block 1.031,7.094 1.406,7.25 0.375,0.156 10 false J/B-B 0.5,7.49 1.083,7.667 0.583,0.177 10 false FL MAIN 6.146,0.521 6.521,0.698 0.375,0.177 10 false #1D+ 6.156,0.927 6.531,1.104 0.375,0.177 10 false #1D- 6.146,1.594 6.521,1.771 0.375,0.177 10 false #2D+ 6.146,2.01 6.521,2.188 0.375,0.177 10 false #2D- 6.146,2.677 6.521,2.854 0.375,0.177 10 false #3D+ 6.146,3.094 6.521,3.271 0.375,0.177 10 false #3D- 6.146,4.188 6.521,4.365 0.375,0.177 10 false #4D- 6.146,3.76 6.521,3.938 0.375,0.177 10 false #4D+ 4.51,6.219 4.74,6.375 0.229,0.156 10 false 2K 2.146,7.302 2.375,7.458 0.229,0.156 10 false 2K 2.146,6.938 2.375,7.094 0.229,0.156 10 false 2B 4.969,6.938 5.198,7.094 0.229,0.156 10 false 2G 4.979,7.292 5.208,7.448 0.229,0.156 10 false 2P 5.885,6.042 6.031,6.198 0.146,0.156 10 false 2 5.875,6.406 6.021,6.563 0.146,0.156 10 false 3 5.885,6.76 6.031,6.917 0.146,0.156 10 false 4 5.844,7.115 6.021,7.271 0.177,0.156 10 false 14 6.146,6.583 6.427,6.75 0.281,0.167 10 false +B2 6.146,6.938 6.427,7.104 0.281,0.167 10 false +B3 6.146,7.302 6.573,7.479 0.427,0.177 10 false MREL 4.802,6.219 4.948,6.375 0.146,0.156 10 false 4 5.021,6.771 5.167,6.927 0.146,0.156 10 false 5 5.021,7.125 5.167,7.281 0.146,0.156 10 false 8 2.177,6.75 2.323,6.906 0.146,0.156 10 false 1 2.198,7.135 2.344,7.292 0.146,0.156 10 false 3 3.406,7.594 4.479,7.75 1.073,0.156 10 false EFI-MAIN NO. 1 2.448,7.063 3.521,7.219 1.073,0.156 10 false EFI-MAIN NO. 1 2.708,6.823 2.854,6.979 0.146,0.156 10 false 1 6.146,4.74 6.521,4.906 0.375,0.167 10 false +BD1 2.969,6.823 3.115,6.979 0.146,0.156 10 false 2 0.677,8.073 1.26,8.25 0.583,0.177 10 false Battery 2.469,0.854 2.885,1.01 0.417,0.156 10 false #10 3.146,0.854 3.563,1.01 0.417,0.156 10 false #1 2.469,1.938 2.885,2.094 0.417,0.156 10 false #20 2.479,3.021 2.896,3.177 0.417,0.156 10 false #30 2.469,4.115 2.885,4.271 0.417,0.156 10 false #40 3.146,1.927 3.563,2.083 0.417,0.156 10 false #2 3.125,3.01 3.542,3.167 0.417,0.156 10 false #3 3.135,4.115 3.552,4.271 0.417,0.156 10 false #4

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
P0201, P0202, P0203 or P0204 is output A
P062D is output B




B

2.INSPECT ECM (+BD1, +BD2 VOLTAGE)

A

7.CHECK WHETHER DTC OUTPUT RECURS
2.INSPECT ECM (+BD1, +BD2 VOLTAGE)
a.
A257437C69
1.281,0.875 1.688,1.115 0.406,0.24 1.781,0.875 2.188,1.115 0.406,0.24 1.229,2.302 1.406,1.521 true 1.854,2.281 1.469,1.521 true 2.594,2.26 2.156,1.531 true 0.146,0.146 0.458,0.344 0.313,0.198 10 false *a 1.375,0.906 1.833,1.177 0.458,0.271 10 false C59 0.74,2.323 1.438,2.542 0.698,0.219 10 false 5 (+BD1) 1.635,2.313 2.302,2.531 0.667,0.219 10 false 4 (+BD2) 1.865,0.917 2.323,1.188 0.458,0.271 10 false C60 2.594,2.302 3.094,2.51 0.5,0.208 10 false 1 (E1)
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C59-5 (+BD1) - C60-1 (E1) Ignition switch ON 11 to 14 V
C59-4 (+BD2) - C60-1 (E1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

4.INSPECT EDU RELAY
3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.INSPECT EDU RELAY

Result:
Proceed to
OK
NG



OK

5.REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

6.REPLACE EDU RELAY
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE EDU RELAY
a.

Replace the EDU relay.


Result:
Proceed to
NEXT



NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

d.

Turn the ignition switch off for 30 seconds.


e.

Start the engine and idle it for 5 seconds or more.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Check the DTCs output on the GTS.

Powertrain > Engine > Trouble Codes
50001 234
HINT:
·

The cylinder with the malfunctioning injector assembly can be determined based on the output DTCs.

·

If the DTC P0201 is output, check the No. 1 injector assembly circuit.

·

If the DTC P0202 is output, check the No. 2 injector assembly circuit.

·

If the DTC P0203 is output, check the No. 3 injector assembly circuit.

·

If the DTC P0204 is output, check the No. 4 injector assembly circuit.




Result:
Proceed to
NEXT



NEXT

8.INSPECT ECM (INJECTOR ASSEMBLY SIGNAL)
8.INSPECT ECM (INJECTOR ASSEMBLY SIGNAL)
a.

Disconnect the injector assembly connectors for all cylinders.

NOTICE:

If only the injector assembly connector of the malfunctioning cylinder is disconnected, the engine will start and there will be rough idling. Therefore, disconnect all injector assembly connectors before inspecting the waveform.



b.

Start the engine.


c.

Check the waveform of the injector assembly connectors using an oscilloscope.

A378121C01
4.458,0.313 5.01,0.583 0.552,0.271 5.125,0.313 5.677,0.583 0.552,0.271 5.813,0.313 6.365,0.583 0.552,0.271 6.469,0.313 7.021,0.583 0.552,0.271 5.677,1.302 4.99,1.948 true 5.719,1.5 6.146,1.948 true 3.656,1.677 4.115,1.875 0.458,0.198 10 false GND 1.5,2.115 2.583,2.333 1.083,0.219 10 false 1 msec./DIV. 3.531,0.5 4.385,0.677 0.854,0.177 10 false 10 V/DIV. 5.521,0.052 6.375,0.229 0.854,0.177 10 false *a 4.677,1.896 5.531,2.073 0.854,0.177 10 false #1*b 4.51,0.375 5.031,0.542 0.521,0.167 10 false C126*b 4.667,2.083 5.521,2.26 0.854,0.177 10 false #2*c 4.667,2.271 5.521,2.448 0.854,0.177 10 false #3*d 4.667,2.469 5.521,2.646 0.854,0.177 10 false #4*e 6.177,1.875 6.677,2.031 0.5,0.156 10 false #10*b 6.177,2.083 6.604,2.271 0.427,0.188 10 false #20*c 6.177,2.271 6.604,2.458 0.427,0.188 10 false #30*d 6.188,2.469 6.646,2.667 0.458,0.198 10 false #40*e 5.177,0.375 5.698,0.542 0.521,0.167 10 false C127*c 5.865,0.375 6.385,0.542 0.521,0.167 10 false C128*d 6.521,0.375 7.042,0.542 0.521,0.167 10 false C129*e
*a Front view of wire harness connector
(Injector Assembly)
*b No. 1 injector assembly connector
*c No. 2 injector assembly connector *d No. 3 injector assembly connector
*e No. 4 injector assembly connector - -


OK:
Tester Connection Condition Specified Condition
C126-6 (#10) - C126-3 (#1) Cranking Correct waveform is as shown
C127-6 (#20) - C127-3 (#2) Cranking Correct waveform is as shown
C128-6 (#30) - C128-3 (#3) Cranking Correct waveform is as shown
C129-6 (#40) - C129-3 (#4) Cranking Correct waveform is as shown



d.

Reconnect the injector assembly connectors for all cylinders.


Result:
Proceed to
OK
NG



OK

9.INSPECT INJECTOR ASSEMBLY (RESISTANCE)

NG

12.INSPECT ECM (INJECTOR ASSEMBLY SIGNAL)
9.INSPECT INJECTOR ASSEMBLY (RESISTANCE)
a.

Inspect the injector assembly of the cylinder relevant to the DTC.

Click hereEngine / Hybrid System>1GD-FTV FUEL>FUEL INJECTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

10.REPLACE INJECTOR ASSEMBLY (RELEVANT CYLINDER)
10.REPLACE INJECTOR ASSEMBLY (RELEVANT CYLINDER)
a.

Replace the injector assembly of the cylinder relevant to the DTC.

Click hereEngine / Hybrid System>1GD-FTV FUEL>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.

·

Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

11.BLEED AIR FROM FUEL SYSTEM
11.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1GD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.INSPECT ECM (INJECTOR ASSEMBLY SIGNAL)
a.

Disconnect the injector assembly connectors for all cylinders.

NOTICE:

If only the injector assembly connector of the malfunctioning cylinder is disconnected, the engine will start and there will be rough idling. Therefore, disconnect all injector assembly connectors before inspecting the waveform.



b.

Start the engine.


c.

Check the waveform of the injector assembly connectors using an oscilloscope.

A340467C03
4.156,0.646 4.573,0.927 0.417,0.281 4.656,0.646 5.094,0.927 0.438,0.281 3.833,2.031 4.198,1.313 true 4.135,1.99 4.24,1.323 true 4.625,2.365 4.302,1.323 true 4.938,2.396 4.365,1.313 true 5.052,2.031 4.469,1.313 true 5.99,2.396 4.531,1.323 true 5.906,2.083 4.656,1.323 true 5.906,0.646 5.792,0.646 5.792,0.646 4.729,1.313 true 1.333,2.104 2.385,2.292 1.052,0.188 10 false 1 msec./DIV. 3.521,1.677 3.948,1.875 0.427,0.198 10 false GND 3.375,0.5 4.427,0.688 1.052,0.188 10 false 10 V/DIV. 4.229,0.719 4.594,0.896 0.365,0.177 10 false C57 4.75,0.698 5.198,0.906 0.448,0.208 10 false C58 3.406,2.083 4.073,2.302 0.667,0.219 10 false 7 (#1D-) 3.948,2.063 4.792,2.25 0.844,0.188 10 false 6 (#1D+) 4.958,2.073 5.573,2.281 0.615,0.208 10 false 2 (#2D-) 5.979,0.573 6.635,0.771 0.656,0.198 10 false 6 (#3D-) 4.948,2.427 5.583,2.625 0.635,0.198 10 false 4 (#4D-) 5.885,2.427 6.563,2.635 0.677,0.208 10 false 1 (#2D+) 5.906,2.083 6.635,2.271 0.729,0.188 10 false 7 (#3D+) 4.26,2.427 4.865,2.656 0.604,0.229 10 false 5 (#4D+) 5.073,0.281 5.729,0.479 0.656,0.198 10 false *a
*a Component with harness connected
(ECM)
- -


OK:
Tester Connection Condition Specified Condition
C57-6 (#1D+) - C57-7 (#1D-) Cranking Correct waveform is as shown
C57-1 (#2D+) - C57-2 (#2D-) Cranking Correct waveform is as shown
C58-7 (#3D+) - C58-6 (#3D-) Cranking Correct waveform is as shown
C57-5 (#4D+) - C57-4 (#4D-) Cranking Correct waveform is as shown



d.

Reconnect the injector assembly connectors for all cylinders.


Result:
Proceed to
OK
NG



OK

13.REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

15.REPLACE ECM
13.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine and idle it for 10 seconds.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.


f.

Confirm that the DTC is not output again.

Powertrain > Engine > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END

15.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED