If the key ID codes of the key and transponder key ECU assembly match, the immobiliser system is unset and the engine start permission signal is sent to the ECM. When the ID codes of the transponder key ECU assembly and ECM match, the engine starts.
If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
DTC is not output.
| Result | Proceed to |
|---|---|
| DTCs are not output (for SFI System) | A |
| DTCs are not output (for ECD System) | B |
| DTCs are output | C |
A
B
C
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Immobiliser Fuel Cut | Status of immobiliser system fuel cut | ON or OFF | - | - |
| Tester Display |
|---|
| Immobiliser Fuel Cut |
OFF is displayed after the engine is started.
| Proceed to |
|---|
| OK (for 2TR-FE) |
| OK (for 2TR-FBE) |
| NG |
OK (for 2TR-FE)
Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
OK (for 2TR-FBE)
Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Using a registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
Engine starts normally.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Using an oscilloscope, check the waveform.
| *A | for 2TR-FBE (for Automatic Transmission) | *B | for 2TR-FE (for Manual Transmission) |
| *C | for 1KD-FTV, 2KD-FTV | *D | for 1GD-FTV, 2GD-FTV |
| *a | Component with harness connected
(ECM) |
*b | Waveform A |
| Item | Content |
|---|---|
| Tester Connection | G45-10 (IMI) - Body ground*1
G83-30 (IMI) - Body ground*2 G86-16 (IMI) - Body ground*3 |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal |
*1: for 2TR-FE, 2TR-FBE
*2: for 1KD-FTV, 2KD-FTV
*3: for 1GD-FTV, 2GD-FTV
Waveform is output normally (refer to illustration).
| Result | Proceed to |
|---|---|
| Normal waveform | A |
| Waveform A not output, or has abnormal wavelength or shape | B |
A
B
Using an oscilloscope, check the waveform.
| *A | for 2TR-FBE (for Automatic Transmission) | *B | for 2TR-FE (for Manual Transmission) |
| *C | for 1KD-FTV, 2KD-FTV | *D | for 1GD-FTV, 2GD-FTV |
| *a | Component with harness connected
(ECM) |
*b | Waveform B |
| *c | Approximately 160 ms | *d | Approximately 270 ms |
| Item | Content |
|---|---|
| Tester Connection | G45-9 (IMO) - Body ground*1
G83-29 (IMO) - Body ground*2 G86-17 (IMO) - Body ground*3 |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal |
*1: for 2TR-FE, 2TR-FBE
*2: for 1KD-FTV, 2KD-FTV
*3: for 1GD-FTV, 2GD-FTV
Waveform is output normally (refer to illustration).
| Result | Proceed to |
|---|---|
| Normal waveform | A |
| Waveform B not output, or has abnormal wavelength or shape (for 2TR-FE) | B |
| Waveform B not output, or has abnormal wavelength or shape (for 2TR-FBE) | C |
| Waveform B not output, or has abnormal wavelength or shape (for 1KD-FTV) | D |
| Waveform B not output, or has abnormal wavelength or shape (for 2KD-FTV) | E |
| Waveform B not output, or has abnormal wavelength or shape (for 1GD-FTV) | F |
| Waveform B not output, or has abnormal wavelength or shape (for 2GD-FTV) | G |
A
B
C
D
E
F
G
Using an oscilloscope, check the waveform.
| *A | for 2TR-FBE (for Automatic Transmission) | *B | for 2TR-FE (for Manual Transmission) |
| *C | for 1KD-FTV, 2KD-FTV | *D | for 1GD-FTV, 2GD-FTV |
| *a | Component with harness connected
(ECM) |
*b | Waveform C |
| *c | Approximately 160 ms | *d | Approximately 270 ms |
| Item | Content |
|---|---|
| Tester Connection | G45-10 (IMI) - Body ground*1
G83-30 (IMI) - Body ground*2 G86-16 (IMI) - Body ground*3 |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal |
*1: for 2TR-FE, 2TR-FBE
*2: for 1KD-FTV, 2KD-FTV
*3: for 1GD-FTV, 2GD-FTV
Waveform is output normally (refer to illustration).
| Result | Proceed to |
|---|---|
| Normal waveform | A |
| Waveform C not output, or has abnormal wavelength or shape | B |
A
B
Register the communication ID between the transponder key ECU assembly and ECM.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Using a registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
Engine starts normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the transponder key ECU assembly with a new one.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Register the key.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Register the ECU communication ID.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Using a registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
Engine starts normally.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 2TR-FE) | B |
| NG (for 2TR-FBE) | C |
| NG (for 1KD-FTV) | D |
| NG (for 2KD-FTV) | E |
| NG (for 1GD-FTV) | F |
| NG (for 1GD-FTV (w/ DPF)) | G |
| NG (for 1GD-FTV (for i-ART)) | H |
| NG (for 2GD-FTV) | I |
| NG (for 2GD-FTV (w/ DPF)) | J |
A
B
Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
C
Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
D
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
E
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
F
G
Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>HOW TO PROCEED WITH TROUBLESHOOTING
H
I
Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
J
Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>HOW TO PROCEED WITH TROUBLESHOOTING
Disconnect the G16 transponder key ECU assembly connector.
Disconnect the G45*1, G83*2 or G86*3 ECM connector.
*1: for 2TR-FE, 2TR-FBE
*2: for 1KD-FTV, 2KD-FTV
*3: for 1GD-FTV, 2GD-FTV
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-13 (EFIO) - G45-10 (IMI) | Always | Below 1 Ω |
| G45-10 (IMI) - Body ground | Always | 10 kΩ or higher |
| G16-13 (EFIO) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-13 (EFIO) - G83-30 (IMI) | Always | Below 1 Ω |
| G83-30 (IMI) - Body ground | Always | 10 kΩ or higher |
| G16-13 (EFIO) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-13 (EFIO) - G86-16 (IMI) | Always | Below 1 Ω |
| G86-16 (IMI) - Body ground | Always | 10 kΩ or higher |
| G16-13 (EFIO) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG