Home › Vehicle Interior › HEATING / AIR CONDITIONING › FRONT AIR CONDITIONING UNIT › from 2016.07
RM33J0E _58 Vehicle Interior _038504 HEATING / AIR CONDITIONING _0192204 FRONT AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  FRONT AIR CONDITIONING UNIT  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



CAUTION:
B414214

w/ Airbag System:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

for Type A: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION

for Type B: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


PROCEDURE

Hide 1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 88710E 3.DISCONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY (for 1GD-FTV, 2GD-FTV)

a.
E315746

Remove the bolt and disconnect the air conditioner tube and accessory assembly.


b.

Remove the 2 O-rings from the air conditioner tube and accessory assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.



Hide 88707 4.DISCONNECT SUCTION PIPE SUB-ASSEMBLY (except 1GD-FTV, 2GD-FTV)

a.
E315745C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the bolt and rotate the hook connector as shown in the illustration.


b.
E315747

Disconnect the suction pipe sub-assembly.


c.

Remove the O-ring from the suction pipe sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.



Hide 88710E 5.DISCONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY (except 1GD-FTV, 2GD-FTV)

a.
E315748

Disconnect the air conditioner tube and accessory assembly.


b.

Remove the O-ring from the air conditioner tube and accessory assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.



Hide 6.DISCONNECT HEATER WATER OUTLET HOSE

a.
E315749

Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water outlet hose.

NOTICE:
·

Do not apply excessive force to the water hose and heater water outlet hose.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 7.DISCONNECT HEATER WATER INLET HOSE

a.
E315750

Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water inlet hose.

NOTICE:
·

Do not apply excessive force to the water hose and heater water inlet hose.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 87128 8.REMOVE HEATER GROMMET

E315751

a.

Detach the claw and remove the heater grommet.


Hide 10.REMOVE FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 55303B 11.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

Hide 58810J 12.REMOVE CONSOLE BOX ASSEMBLY (w/ Console Box Lid)

Hide 58811A 13.REMOVE FRONT CONSOLE BOX (w/o Console Box Lid)

Hide 87211 14.REMOVE NO. 1 AIR DUCT

a.
E320358

Remove the bolt.


b.

Detach the claw and remove the No. 1 air duct.

NOTICE:
·

When removing, do not crack or deform the lower heater case of the air conditioning radiator assembly.

·

If the No. 1 air duct is reused, it may fall off or abnormal noise may occur. Therefore, make sure to replace it with a new one.




Hide 87211A 15.REMOVE NO. 2 AIR DUCT

a.
E320359

Detach the claw and remove the No. 2 air duct.

NOTICE:
·

When removing, do not crack or deform the lower heater case of the air conditioning radiator assembly.

·

If the No. 2 air duct is reused, it may fall off or abnormal noise may occur. Therefore, make sure to replace it with a new one.




Hide 16.REMOVE STEERING COLUMN ASSEMBLY

Hide 62112 18.REMOVE COWL SIDE TRIM BOARD LH

Hide 62111C 20.REMOVE COWL SIDE TRIM BOARD RH

Hide 67918E 21.REMOVE REAR DOOR SCUFF PLATE LH (for Double Cab)

Hide 67917C 22.REMOVE REAR DOOR SCUFF PLATE RH (for Double Cab)

Hide 62414A 23.REMOVE LOWER CENTER PILLAR GARNISH LH (for Double Cab)

Hide 62413A 24.REMOVE LOWER CENTER PILLAR GARNISH RH (for Double Cab)

Hide 25.REMOVE FRONT FLOOR CARPET ASSEMBLY

a.

for LHD:

Remove the 5 clips.

E320360C04
1.802,1.125 2.063,1.354 0.26,0.229 12 true *A
*A for LHD - -
V100155

Fastener
V113147

Remove in this Direction



b.

for RHD:

Remove the 4 clips.


c.

Detach each fastener.


d.

Detach the guide and fold back the front floor carpet assembly as shown in the illustration.


Hide 55395C 26.REMOVE NO. 1 INSTRUMENT PANEL INNER BRACKET COVER LH (for LHD)

E323201

a.

Remove the 3 clips and No. 1 instrument panel inner bracket cover LH


Hide 55215D 27.REMOVE NO. 3 DASH PANEL INSULATOR PAD

a.
E325193C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the No. 3 dash panel insulator pad as shown in the illustration.


Hide 55214C 28.REMOVE NO. 2 DASH PANEL INSULATOR PAD

a.
E325194C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the No. 2 dash panel insulator pad as shown in the illustration.


Hide 58861B 29.REMOVE NO. 1 CONSOLE BOX DUCT (w/ Rear Resistor Duct)

a.
E320363C03
0.333,0.188 0.583,0.427 0.25,0.24 12 true *A
*A w/ Smart Entry and Start System


for Automatic Transmission:

i.

Remove the 2 bolts.


ii.

w/ Smart Entry and Start System:

Detach the clamp and remove the No. 2 console box mounting bracket.


iii.
E320364

Remove the 2 clips and No. 1 console box duct.



b.
E323937C02
2.333,0.25 2.594,0.5 0.26,0.25 12 true *A
*A w/ Smart Entry and Start System


for Manual Transmission:

i.

Remove the 2 bolts.


ii.

w/ Smart Entry and Start System:

Detach the clamp and remove the No. 2 console box mounting bracket.


iii.
E323938

Remove the 3 clips and No. 1 console box duct.



Hide 55306A 30.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.
E320365C03
0,0 0,0 false
V100135

Nut
V100136

Bolt
V100137

Screw


Detach the clamp.


b.

Remove the nut, bolt, 4 screws and No. 1 instrument panel brace sub-assembly.


Hide 55307C 31.REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.
E320366C03
0,0 0,0 false
V100135

Nut
V100136

Bolt
V100137

Screw


Remove the nut, bolt, 3 screws and No. 2 instrument panel brace sub-assembly.


Hide 82141 32.DISCONNECT INSTRUMENT PANEL WIRE

a.
E320367

for Automatic Air Conditioning System:

i.

Disconnect the connector.


ii.

Detach the clamp.



b.
E320368

for Manual Air Conditioning System:

i.

Disconnect the connector.


ii.

Detach the clamp.



c.

Remove each bolt and each ground wire.

E320369C05
2.26,4.406 2.531,4.625 0.271,0.219 12 true *A 2.271,6.156 2.563,6.375 0.292,0.219 12 true *B 3.198,1.542 3.385,1.698 0.188,0.156 10 true *1 2.76,0.854 2.948,1.01 0.188,0.156 10 true *1 3.719,1.448 3.906,1.604 0.188,0.156 10 true *1 3.823,0.51 4.01,0.667 0.188,0.156 10 true *1 4.354,1.344 4.542,1.5 0.188,0.156 10 true *1 6.521,1.188 6.708,1.344 0.188,0.156 10 true *1
*A for Manual Air Conditioning System *B for Automatic Air Conditioning System
*1 Ground Wire - -



d.

Disconnect each connector and detach each clamp.


e.

Remove each bolt, nut and screw, and then disconnect the instrument panel wire.


Hide 55330B 33.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY

NOTICE:
·

Be sure to support the air conditioning unit assembly when removing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.

·

When removing the air conditioning unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.



a.
E325411C02
0.073,0.094 0.385,0.302 0.313,0.208 12 true *A
*A for Driver Side
V100155

Protective Tape


Put protective tape around the hole plug.


b.

Using a screwdriver with its tip wrapped with protective tape, remove the 2 hole plugs.


c.

for Automatic Transmission:

Remove the 11 bolts.

E320370C04
1.094,0.906 1.344,1.125 0.25,0.219 12 true *A
*A for Manual Transmission - -
V100135

Bolt A
V100136

Bolt B
V100137

Bolt C
V100138

Bolt D



d.

for Manual Transmission:

Remove the 12 bolts.


Hide 55950G 34.REMOVE DEFROSTER NOZZLE ASSEMBLY

E320371

a.

Detach the claw and remove the defroster nozzle assembly.


Hide 35.REMOVE AIR CONDITIONING UNIT ASSEMBLY

NOTICE:
·

Be sure to support the air conditioning unit assembly when removing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.

·

When disassembling the air conditioning unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.



a.

Disconnect the drain cooler hose.

E320372


b.

Remove the nut and air conditioning unit assembly and instrument panel reinforcement assembly.


Hide 87211B 36.REMOVE NO. 3 AIR DUCT

a.
E320373

Detach the claw and remove the No. 3 air duct.