Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.07
RM33J0E _54 Brake _038477 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0192391 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the ECU to display the DTC by blinking the ABS warning light and slip indicator light.

WIRING DIAGRAM

C332706E05
0.885,0.698 1.5,0.896 0.615,0.198 10 false CANH 5.958,0.719 6.573,0.917 0.615,0.198 10 false CANH 0.885,1.417 1.5,1.615 0.615,0.198 10 false CANL 5.969,1.427 6.583,1.625 0.615,0.198 10 false CANL 1.073,2.167 1.688,2.365 0.615,0.198 10 false TC 3.427,2.177 4.042,2.375 0.615,0.198 10 false TC 3.427,2.802 4.042,3 0.615,0.198 10 false CG 3.219,3.385 3.448,3.594 0.229,0.208 10 false G8 3.479,3.385 4.094,3.583 0.615,0.198 10 false DLC3 3.177,2.656 3.385,2.927 0.208,0.271 10 false 4 3.125,2 3.333,2.271 0.208,0.271 10 false 13 0.698,3.396 1.313,3.594 0.615,0.198 10 false ECM 5.552,1.917 7.115,2.385 1.563,0.469 10 false Skid Control ECU (Brake Actuator Assembly) 5.25,1.906 5.479,2.115 0.229,0.208 10 false A4 5.667,0.479 5.875,0.75 0.208,0.271 10 false 22 5.656,1.177 5.865,1.448 0.208,0.271 10 false 10 1.417,2.167 1.74,2.385 0.323,0.219 10 false G46 1.438,1.917 2.052,2.115 0.615,0.198 10 false 19*1 1.823,0.698 2.146,0.917 0.323,0.219 10 false G85 1.823,1.917 2.438,2.115 0.615,0.198 10 false 25*2 2.219,2.167 2.542,2.385 0.323,0.219 10 false G84 2.26,1.927 2.875,2.125 0.615,0.198 10 false 11*3 1.427,1.406 1.75,1.625 0.323,0.219 10 false G45 1.427,1.156 2.042,1.354 0.615,0.198 10 false 14*1 1.833,1.156 2.448,1.354 0.615,0.198 10 false 28*2 1.823,2.167 2.146,2.385 0.323,0.219 10 false G85 2.219,1.417 2.542,1.635 0.323,0.219 10 false G83 2.26,1.167 2.875,1.365 0.615,0.198 10 false 23*3 1.406,0.698 1.729,0.917 0.323,0.219 10 false G45 1.448,0.458 2.063,0.656 0.615,0.198 10 false 13*1 1.833,0.479 2.448,0.677 0.615,0.198 10 false 17*2 1.823,1.406 2.146,1.625 0.323,0.219 10 false G85 2.229,0.708 2.552,0.927 0.323,0.219 10 false G83 2.26,0.479 2.875,0.677 0.615,0.198 10 false 24*3 4.927,3.198 6.844,3.5 1.917,0.302 10 false *1: for 2TR-FE and 2TR-FBE 4.958,3.563 6.875,3.865 1.917,0.302 10 false *2: for 1GD-FTV and 2GD-FTV 4.969,3.948 6.885,4.25 1.917,0.302 10 false *3: for 1KD-FTV and 2KD-FTV 0.51,4.313 2.427,4.615 1.917,0.302 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM

Result:
Proceed to
DTC is not output
DTC is output



DTC is not output

2.INSPECT DLC3

DTC is output

2.INSPECT DLC3
a.
C269109C33
0.115,1.49 0.479,1.719 0.365,0.229 1.635,1.813 1.823,1.49 true 1.302,0.281 1.573,0.792 true 1.073,0.198 1.417,0.438 0.344,0.24 10 false CG 1.521,1.844 1.833,2.042 0.313,0.198 10 false TC 0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 0.198,1.521 0.51,1.719 0.313,0.198 10 false G8
*a Front view of DLC3


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G8-13 (TC) - G8-4 (CG) Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

3.REPLACE ECM

NG

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
3.REPLACE ECM
a.
C269109C33
0.115,1.49 0.479,1.719 0.365,0.229 1.635,1.813 1.823,1.49 true 1.302,0.281 1.573,0.792 true 1.073,0.198 1.417,0.438 0.344,0.24 10 false CG 1.521,1.844 1.833,2.042 0.313,0.198 10 false TC 0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 0.198,1.521 0.51,1.719 0.313,0.198 10 false G8
*a Front view of DLC3


Turn the ignition switch off.



c.

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.


SST
09843-18040  

d.

Check that the ABS warning and slip indicator light are blinking.

OK:

The ABS warning and slip indicator light are blinking.



Result:
Proceed to
OK
NG



OK

END

NG

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the G46*1, G85*2 or G84*3 ECM connector.

*1: for 2TR-FE and 2TR-FBE

*2: for 1GD-FTV and 2GD-FTV

*3: for 1KD-FTV and 2KD-FTV



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2TR-FE and 2TR-FBE:
Tester Connection Condition Specified Condition
G8-13 (TC) - G46-19 (TC) Always Below 1 Ω
G8-13 (TC) or G46-19 (TC) - Body ground Always 10 kΩ or higher

for 1GD-FTV and 2GD-FTV:
Tester Connection Condition Specified Condition
G8-13 (TC) - G85-25 (TC) Always Below 1 Ω
G8-13 (TC) or G85-25 (TC) - Body ground Always 10 kΩ or higher

for 1KD-FTV and 2KD-FTV:
Tester Connection Condition Specified Condition
G8-13 (TC) - G84-11 (TC) Always Below 1 Ω
G8-13 (TC) or G84-11 (TC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.
C269109C32
0.115,1.49 0.479,1.719 0.365,0.229 1.302,0.281 1.573,0.792 true 1.073,0.198 1.417,0.438 0.344,0.24 10 false CG 0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 0.208,1.521 0.521,1.719 0.313,0.198 10 false G8
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE ECM
a.
C269109C33
0.115,1.49 0.479,1.719 0.365,0.229 1.635,1.813 1.823,1.49 true 1.302,0.281 1.573,0.792 true 1.073,0.198 1.417,0.438 0.344,0.24 10 false CG 1.521,1.844 1.833,2.042 0.313,0.198 10 false TC 0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 0.198,1.521 0.51,1.719 0.313,0.198 10 false G8
*a Front view of DLC3


Replace the ECM.

for 1GD-FTV: Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECM>REMOVAL

for 1KD-FTV: Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECM>REMOVAL

for 2GD-FTV: Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECM>REMOVAL

for 2KD-FTV: Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECM>REMOVAL

for 2TR-FE: Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>ECM>REMOVAL

for 2TR-FBE: Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>ECM>REMOVAL


b.

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.


SST
09843-18040  

c.

Check that the ABS warning and slip indicator light are blinking.

OK:

The ABS warning and slip indicator light are blinking.



Result:
Proceed to
OK
NG



OK

END

NG