Home › Drivetrain › AC60F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FBE) › from 2016.07
RM33J0E _52 Drivetrain _038466 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0265184 AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FBE) C

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FBE)  P2774  Four Wheel Drive (4WD) Low Switch Circuit High  


DESCRIPTION

The ECM detects the signal from the L4 detection switch.

This DTC indicates that the L4 detection switch remains off.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2774 Four Wheel Drive (4WD) Low Switch Circuit High L4 detection switch remains off while the vehicle is being driven under the following conditions for 1.8 seconds or more (1-trip detection logic):
(a) Output shaft speed is between 1000 and 3000 rpm.
(b) Transfer position switch is in L4.
·

Open in L4 detection switch circuit

·

Transfer shift actuator assembly

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM monitors the L4 detection switch to determine when the transfer case L4 gears are engaged. If the transfer case H4 gears remain engaged under the following conditions, the ECM will conclude that there is a malfunction of the L4 detection switch, illuminate the MIL and store the DTC:

·

The L4 detection switch indicates that the H4 transfer case gears are engaged.

·

The transfer position switch is in L4.

·

The transfer case output shaft speed is between 1000 and 3000 rpm.

·

The specified time period has elapsed.


CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the transfer position switch to L4.

2.

Drive the vehicle at 15 to 20 km/h (9 to 12 mph) for 1.8 seconds or more.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TRANSFER SHIFT ACTUATOR ASSEMBLY - ECM)
a.

Disconnect the C41 transfer shift actuator assembly connector.


b.

Disconnect the G46 ECM connector


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
C41-9 (L4) - G46-25 (L4) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK TRANSFER SHIFT ACTUATOR ASSEMBLY (TRANSFER SHIFT ACTUATOR ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TRANSFER SHIFT ACTUATOR ASSEMBLY (TRANSFER SHIFT ACTUATOR ASSEMBLY - BODY GROUND)
a.
C325622C29
1.458,0.646 1.833,0.896 0.375,0.25 1.844,2.021 1.948,2.688 true 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a 1.521,0.698 1.979,0.896 0.458,0.198 10 false C41 1.813,2.76 2.271,2.958 0.458,0.198 10 false GND
*a Front view of wire harness connector
(to Transfer Shift Actuator Assembly)


Disconnect the transfer shift actuator assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
C41-10 (GND) - Body ground Aways Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT TRANSFER SHIFT ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT TRANSFER SHIFT ACTUATOR ASSEMBLY
a.

Inspect the transfer shift actuator assembly.

Click hereDrivetrain>VF2CM TRANSFER / 4WD / AWD>TRANSFER ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE TRANSFER SHIFT ACTUATOR ASSEMBLY