Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM
RM3270E _56 Audio / Visual / Telematics _041701 PARK ASSIST / MONITORING _0197847 TOYOTA PARKING ASSIST-SENSOR SYSTEM J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  Illumination Circuit  


DESCRIPTION

Power is supplied to the back sonar or clearance sonar switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E318093E01
5.531,1.031 6.146,1.229 0.615,0.198 10 false ILL- 4.302,0.917 4.667,1.115 0.365,0.198 10 false ILL- 4.677,0.917 5.042,1.115 0.365,0.198 10 false 4 2.917,0.917 3.281,1.115 0.365,0.198 10 false ILL+ 2.698,0.917 3.063,1.115 0.365,0.198 10 false 5 0.75,1.01 1.865,1.26 1.115,0.25 10 false from TAIL Relay 5.219,0.927 5.583,1.125 0.365,0.198 10 false 21 5.094,2.031 5.708,2.229 0.615,0.198 10 false G9 5.104,2.198 7.083,2.417 1.979,0.219 10 false Combination Meter Assembly 2.771,1.448 3.385,1.646 0.615,0.198 10 false G87 2.781,1.594 4.74,2 1.958,0.406 10 false Back Sonar or Clearance Sonar Switch Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the relay for circuits related to this system before performing the following procedure.

·

When replacing the combination meter assembly, make sure to replace it with a new one.



PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the back sonar or clearance sonar switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the tail or head position.


Result:
Result Proceed to
Illumination comes on for all components except back sonar or clearance sonar switch assembly A
No illumination comes on (back sonar or clearance sonar switch assembly, hazard switch, heater control switch, etc.) B



A

2.INSPECT BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY

B

2.INSPECT BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY
a.

Remove the back sonar or clearance sonar switch assembly.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE SONAR MAIN SWITCH>REMOVAL


b.

Inspect the back sonar or clearance sonar switch assembly.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE SONAR MAIN SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY ILLUMINATION SIGNAL)

NG

REPLACE BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY ILLUMINATION SIGNAL)
a.
E318094C01
1.333,0.219 1.917,0.469 0.583,0.25 2.26,1.938 1.927,1.938 1.927,1.938 1.76,1.438 true 0.042,0.042 0.354,0.24 0.313,0.198 10 false *a 2.323,1.844 2.802,2.031 0.479,0.188 10 false ILL+ 1.49,0.26 1.969,0.448 0.479,0.188 10 false G87
*a Front view of wire harness connector
(to Back Sonar or Clearance Sonar Switch Assembly)


Disconnect the back sonar or clearance sonar switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G87-5 (ILL+) - Body ground Light control switch in tail or head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the G87 back sonar or clearance sonar switch assembly connector.


b.

Disconnect the G9 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G87-4 (ILL-) - G9-21 (ILL-) Always Below 1 Ω
G87-4 (ILL-) or G9-21 (ILL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR