Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE › 2015.08–2016.01
RM3270E _58 Vehicle Interior _041710 SUPPLEMENTAL RESTRAINT SYSTEMS _0199689 SPIRAL CABLE A

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the spiral cable sub-assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal w/ Power Back Door System:
Reset back door close position
Power back door system (Click here)

PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 45100 4.REMOVE STEERING WHEEL ASSEMBLY

Hide 5.INSPECT SPIRAL CABLE SUB-ASSEMBLY

a.
B404076C01
0.51,2.5 0.927,2.917 0.417,0.417 0.865,2.146 1.281,2.271 true 1.323,2.188 1.635,2.344 0.313,0.156 10 false *a 0.521,2.51 0.719,2.698 0.198,0.188 10 true *b
*a Check Window
*b Matchmark
V100144

U-Turn Point


Check the check window shown in the illustration.

With the steering wheel straight ahead, align the matchmarks to check the U-turn point of the cable from the check window.

NOTICE:

When the conditions above cannot be checked via the check window with the front wheels facing straight ahead, there may be a malfunction in the spiral cable sub-assembly. In this case, replace the spiral with cable sensor sub-assembly with a new one.



Hide 45287 6.REMOVE LOWER STEERING COLUMN COVER

Hide 45286B 7.REMOVE UPPER STEERING COLUMN COVER

Hide 8.REMOVE SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Do not replace the spiral cable sub-assembly with the battery connected and the ignition switch ON.

·

Do not rotate the spiral cable sub-assembly with the battery connected and the ignition switch ON.

·

When rotating the spiral cable sub-assembly to check the operation of the sub-assembly (checking for abnormal noise, checking the Data List, etc.), make sure to perform the inspection with the steering wheel assembly installed.



a.
B409179C01
0.615,2.427 1.167,2.208 true 1.219,2.125 1.531,2.281 0.313,0.156 10 false *a
*a Slider
V113147

Slide in this Direction


Slide the slider to release the lock, and then disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.



b.

Disconnect each connector.


c.
B409180

Detach the claw and remove the spiral cable sub-assembly.


Hide 9.REMOVE SPIRAL CABLE (w/ Steering Sensor)

NOTICE:
·

Remove the spiral cable from the steering sensor only when replacing it.

·

Removing the steering sensor from the spiral cable sub-assembly without using a lock pin may result in a misaligned center position of the steering sensor. Therefore, make sure to use the lock pin provided with a new spiral cable when removing the steering sensor from the spiral cable sub-assembly.



a.
C238437

Install the lock pin to the steering sensor.

NOTICE:
·

Use the lock pin provided with a new spiral cable.

·

Do not remove the lock pin before the spiral cable is installed to the steering sensor.




b.
B295949

Detach the 6 claws and remove the spiral cable from the steering sensor.