Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CURTAIN SHIELD AIRBAG ASSEMBLY
RM3270E _58 Vehicle Interior _041710 SUPPLEMENTAL RESTRAINT SYSTEMS _0199692 CURTAIN SHIELD AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  CURTAIN SHIELD AIRBAG ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the curtain shield airbag assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal w/ Power Back Door System:
Reset back door close position
Power back door system (Click here)

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the RH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.REMOVE ROOF HEADLINING ASSEMBLY

Hide 62170A 4.REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY RH

CAUTION:
B399183C01
0.667,0.5 0.823,0.698 0.156,0.198 10 false .
V100155

Deployment Side


·

When storing the curtain shield airbag assembly RH, keep the airbag deployment side facing upward.

·

If the airbag deploys for any reason, it may cause a serious accident.



a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




c.
B409191C01
2.219,0.385 2.531,0.573 true 2.042,0.271 2.354,0.427 0.313,0.156 10 false *a
*a Connector Lock
V100155

Protective Tape
V113147

Release in this Direction


Using a screwdriver, pull up the connector lock and disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Tape the screwdriver tip before use.



d.

Remove the clip.

NOTICE:

The clip must not be reused.


HINT:

Use the same procedure for the other clips.


i.
B378006C01
2.458,0.917 2.781,0.917 false 2.823,0.833 3.135,1.031 0.313,0.198 10 false *1
*1 Pin


Using needle-nose pliers, release the lock by pinching the 2 locks of the pin, and then pull out the pin from the clip.


ii.
B378358

Using 2 screwdrivers, detach the clip by inserting the screwdrivers into the groove of the clip as shown in the illustration, and then remove the clip from the vehicle body.



e.

Remove the 2 bolts.

NOTICE:

The bolts must not be reused.



f.

Detach the claw and remove the curtain shield airbag assembly RH.

B409193