Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SIDE AIRBAG SENSOR › 2015.08–2016.01
RM3270E _58 Vehicle Interior _041710 SUPPLEMENTAL RESTRAINT SYSTEMS _0199697 SIDE AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  SIDE AIRBAG SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the RH side.



PROCEDURE

Hide 89865 1.INSTALL DOOR SIDE AIRBAG SENSOR RH

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
·
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·
B392779

If this procedure is performed without disconnecting the negative (-) terminal of the battery, the airbag may deploy even if an impact is applied only to the door side airbag sensor RH. Therefore, make sure that the negative (-) terminal of the battery is disconnected before performing this procedure.




c.

Attach the guide and hold the door side airbag sensor RH in place.


d.

Install the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:
·

If the door side airbag sensor RH has been dropped, replace it with a new one.

·

When installing the door side airbag sensor RH, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

·

Tighten the bolt while holding the door side airbag sensor RH because the door side airbag sensor RH guide is easily damaged.




e.

Connect the airbag connector.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


i.

Before connecting the airbag connector, check that the position of the housing lock is correct as shown in the illustration.

B340848C02
4.583,0.594 4.896,0.75 0.313,0.156 10 *a 4.677,1.875 4.99,2.031 0.313,0.156 10 *b 1.385,0.615 1.698,0.771 0.313,0.156 10 *a 1.448,1.865 1.76,2.021 0.313,0.156 10 *b
*a Incorrect *b Correct



ii.

While holding the CPA, be sure to engage the connectors until they are locked and check that the CPA is in its original position (when locking, make sure that a click sound can be heard).

NOTICE:

Do not push down the upper part of the CPA shown in the illustration when connecting the airbag connector.


B399097C02
2.396,1.031 2.813,0.615 true 2.479,1.802 2.479,1.385 true 2.26,0.813 2.677,0.396 true 2.708,0.281 3.021,0.438 0.313,0.156 10 false *c 5.917,2.208 6.229,2.365 0.313,0.156 10 false *d 2.875,0.51 3.188,0.667 0.313,0.156 10 false *a 2.417,1.844 2.729,2 0.313,0.156 10 false *b
*a Housing Lock *b CPA
*c CPA Upper Part *d Connection is Completed
V113147

Connect in this Direction - -




f.

Check that there is no looseness in the installation parts of the door side airbag sensor RH.


Hide 67601 2.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY RH

Hide 69283 3.INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG RH

Hide 4.INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

Hide 5.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

Hide 74210 6.INSTALL FRONT ARMREST ASSEMBLY RH

Hide 67491A 7.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH RH

Hide 8.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION