Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › 2015.08–2016.01
RM3270E _59 Vehicle Exterior _041717 DOOR / HATCH _0205101 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the RH side.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 75921C 2.INSTALL NO. 1 BLACK OUT TAPE RH

HINT:

The procedure described below is for the LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>BLACK OUT TAPE(for Front Door)>INSTALLATION


Hide 67861 3.INSTALL FRONT DOOR WEATHERSTRIP RH

a.
B404270

Attach the clip to install the front door weatherstrip RH.


Hide 68610B 4.INSTALL FRONT DOOR CHECK ASSEMBLY RH

a.

Apply MP grease to the sliding area of the front door check assembly RH.


b.

When reusing a bolt:

i.

Clean the threads of the bolt (B) with non-residue solvent.


ii.

Apply adhesive to the threads of the bolt (B).

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.




c.
B404271C02
0,0 0,0 false
V100135

Bolt (A)
V100136

Bolt (B)


Install the front door check assembly RH with the 2 bolts (A) and bolt (B).

Torque:
Bolt (A) : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Bolt (B) : 30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 67837B 5.INSTALL FRONT DOOR DUST PROOF SEAL

a.
B406723

Attach the claw to install 3 new front door dust proof seals.


Hide 67001A 6.INSTALL FRONT DOOR PANEL CUSHION

a.
B404267

Attach the claw to install 2 new front door panel cushions.


Hide 75710 7.INSTALL FRONT DOOR BELT MOULDING ASSEMBLY RH

HINT:

The procedure described below is for the LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT DOOR BELT MOULDING>INSTALLATION


Hide 69311A 8.INSTALL FRONT DOOR LOCK OPEN ROD RH

a.
B404276C01
0,0 0,0 false
V113147

Install in this Direction


Attach the snap to install the front door lock open rod RH to the front door outside handle frame sub-assembly RH as shown in the illustration.


Hide 69201A 9.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY RH

a.

Apply MP grease to the sliding area of the front door outside handle frame sub-assembly RH.


b.
B404265C02
1.323,1.594 1.167,1.594 1.167,1.594 1.167,1.208 false 1.667,1.427 1.927,1.427 1.927,1.427 1.927,1.042 false 2.344,0.885 2.708,0.885 true 1.344,1.49 1.656,1.688 0.313,0.198 10 false *a 2.729,0.781 3.042,0.979 0.313,0.198 10 false *a 1.469,1.313 1.781,1.51 0.313,0.198 10 false *b
*a Clamp
*b Guide


Attach the guide and clamp to connect the wire harness.


c.
B408832C01
1.24,0.771 0.979,0.469 0.979,0.469 0.74,0.469 true 2.26,0.458 2.26,0.188 2.26,0.188 2.49,0.188 true 2.24,0.802 2.375,0.969 2.375,0.969 2.604,0.969 true 2.521,0.875 2.74,1.115 0.219,0.24 10 true *b 0.604,0.365 0.823,0.604 0.219,0.24 10 true *a 2.427,0.083 2.646,0.323 0.219,0.24 10 true *b
*a Grommet
*b Guide
V113147

Install in this Direction


Attach the grommet and guide to install the front door outside handle frame sub-assembly RH as shown in the illustration.


d.

Using a T30 "TORX" socket wrench, install the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69242E 10.INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD

a.
B408833C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw to install the front door rear outside handle pad.


Hide 69241H 11.INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD

a.
B408834C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw to install the front door front outside handle pad.


Hide 69210 12.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY RH

a.
B408835C01
0,0 0,0 false
V113147

Install in this Direction


Install the front door outside handle assembly RH as shown in the illustration.


b.

w/ Smart Entry and Start System:

i.
B408837

Connect the connector.


ii.
B408836C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw to close the connector cover as shown in the illustration.



Hide 69318C 13.INSTALL DOOR LOCK WIRING HARNESS SEAL

Hide 69710B 14.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY RH

Hide 69750C 15.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY RH

Hide 69035A 16.INSTALL FRONT DOOR LOCK COVER SUB-ASSEMBLY RH

Hide 69310 17.INSTALL FRONT DOOR LOCK ASSEMBLY RH

Hide 69217D 18.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)

a.
B404288C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide and claw to install the front door outside handle cover to the lock cylinder assembly as shown in the illustration.


Hide 19.INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)

a.

Apply MP grease to the sliding area of the front door outside handle cover with lock cylinder assembly.


b.
B408839C01
0.688,1.885 1.198,1.885 true 1.177,1.802 1.49,2 0.313,0.198 10 true *1
*1 Hole Plug
V113147

Install in this Direction


Install the front door outside handle cover with lock cylinder assembly as shown in the illustration.

HINT:

Check that the front door lock cylinder assembly is inserted into the front door lock assembly RH.



c.

Using a T30 "TORX" socket wrench, install the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


d.

Install the hole plug.


Hide 69217D 20.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)

a.
B408838C01
2.656,1.958 3.198,1.958 true 2.49,1.854 2.802,2.052 0.313,0.198 10 true *1
*1 Hole Plug
V113147

Install in this Direction


Attach the claw to install the front door outside handle cover as shown in the illustration.


b.

Using a T30 "TORX" socket wrench, install the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


c.

Install the hole plug.


Hide 67403F 21.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY RH

a.
B408817

Attach the guide to install the front door rear lower frame sub-assembly RH.


b.

Install the bolt.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


Hide 85710D 22.INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

Hide 69801 23.INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY RH

a.

Apply MP grease to the sliding area of the front door window regulator sub-assembly RH.


b.
B408818C02
0,0 0,0 false
V100135

Bolt
V100136

Connector
V100137

Temporarily Bolt


Temporarily install the temporarily bolt to the front door window regulator sub-assembly RH.


c.

Install the front door window regulator sub-assembly RH with the 5 bolts and temporarily bolt.

Torque:
Bolt : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Temporarily Bolt : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


d.

Connect the connector.


Hide 68101 24.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY RH

a.

Temporarily install the power window regulator master switch assembly.


b.

Connect the cable to the negative (-) battery terminal.


c.

Move the front door window regulator sub-assembly RH so that the front door glass sub-assembly RH bolts can be seen.


d.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



e.

Remove the power window regulator master switch assembly.


f.
B408840C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Install the front door glass sub-assembly RH as shown in the illustration.

NOTICE:

Be careful not to damage the glass.



g.
B408814

Install the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 68141C 25.INSTALL FRONT DOOR GLASS RUN RH

a.
B408816

Attach the guide to install a new front door glass run RH.


Hide 26.INSTALL SCREW GROMMET

B408854

a.

Attach the claw to install 2 new screw grommets.


Hide 67831 27.INSTALL FRONT DOOR SERVICE HOLE COVER RH

a.

Apply new butyl tape to the front door panel.


b.
B408841C01
2.688,0.438 2.833,0.438 true 0.333,0.24 0.427,0.24 0.427,0.24 0.531,0.375 true 2.813,0.333 3,0.563 0.188,0.229 10 true *a 0.167,0.146 0.354,0.375 0.188,0.229 10 true *a
*a Reference Point
V100143

Butyl Tape


Pass the front door inside locking cable assembly RH and front door lock remote control cable assembly RH through a new front door service hole cover RH, and then attach the front door service hole cover RH using the reference points on the front door panel.

HINT:
·

Securely install the front door service hole cover RH to prevent wrinkles and air bubbles.

·

There should be no wrinkles or folds after installing the front door service hole cover RH.

·

After installing the front door service hole cover RH, check the seal quality.




c.

Attach the clamp.


d.

Install the ground wire with the ground bolt.


Hide 87910 28.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY RH

HINT:

The procedure described below is for the LH side.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSTALLATION


Hide 89865 29.INSTALL DOOR SIDE AIR BAG SENSOR RH

Hide 86160P 30.INSTALL FRONT NO. 2 SPEAKER ASSEMBLY

Hide 86160 31.INSTALL FRONT NO. 1 SPEAKER ASSEMBLY

Hide 68171B 32.INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP RH

a.
B408842

Install a new front door inner glass weatherstrip RH to the front door trim board sub-assembly RH and fold down the claw in the directions indicated by the arrows in the illustration.


Hide 69205 33.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY RH

a.
B408845C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw to install the front door inside handle sub-assembly RH to the front door trim board sub-assembly RH.


Hide 67601 34.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY RH

a.
B408844C01
0.896,0.927 1.271,0.427 1.271,0.427 1.604,0.427 true 0.896,1.375 1.25,1.823 1.25,1.823 1.688,1.823 true 1.521,0.344 1.771,0.583 0.25,0.24 10 true *1 1.552,1.75 1.802,1.99 0.25,0.24 10 true *2
*1 Front Door Inside Locking Cable Assembly RH
*2 Front Door Lock Remote Control Cable Assembly RH
V113147

Install in this Direction


Attach the clamp to connect the front door lock remote control cable assembly RH and front door inside locking cable assembly RH as shown in the illustration.


b.
B408843C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide as shown in the illustration.


c.
B408846

Attach the clip to install the front door trim board sub-assembly RH.


d.
B408807

Install the 3 screws.


Hide 69283 35.INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG RH

a.
B408885

Attach the claw to install the front door inside handle bezel plug RH as shown in the illustration.


Hide 81230 36.INSTALL COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

Hide 67665C 37.INSTALL FRONT DOOR TRIM REFLECTOR RH (w/ Reflex Reflector Assembly)

a.
B405482C01
0.104,0.083 0.417,0.281 0.313,0.198 10 true *A 0.135,2.344 0.448,2.542 0.313,0.198 10 true *B
*A for RH Side
*B for LH Side
V100155

Protective Tape
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Attach the guide and claw to install the front door trim reflector RH as shown in the illustration.


b.

Remove the protective tape.


Hide 84820 38.INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Driver Side)

Hide 84870A 39.INSTALL OUTER MIRROR SWITCH ASSEMBLY (for Driver Side)

Hide 40.INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

a.

Connect the each connector.


b.
B408847C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and clip to install the power window regulator master switch assembly with front door armrest base panel as shown in the illustration.


Hide 84810 41.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)

Hide 42.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

a.

Connect the connector.


b.
B399667C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and clip to install the power window regulator switch assembly with front door armrest base panel as shown in the illustration.


Hide 74210 43.INSTALL FRONT ARMREST ASSEMBLY RH

a.
B408848C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and clip to install the front armrest assembly RH.


Hide 67491A 44.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH RH

a.
B408803

Attach the claw and clip to install the front door lower frame bracket garnish RH.


Hide 45.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION