Home › Vehicle Interior › HEATING / AIR CONDITIONING › REAR AIR CONDITIONING UNIT › 2015.08–2016.01
RM3270E _58 Vehicle Interior _041713 HEATING / AIR CONDITIONING _0199984 REAR AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  REAR AIR CONDITIONING UNIT  INSTALLATION  


PROCEDURE

Hide 88510T 1.INSTALL REAR COOLING UNIT ASSEMBLY (for Automatic Air Conditioning System)

a.

Install the rear cooling unit assembly with the 3 bolts and tighten the bolts in the order shown in the illustration.

E317565C02
1.052,2.135 1.302,2.354 0.25,0.219 10 true (1) 3.406,2.344 3.656,2.563 0.25,0.219 10 true (2) 3.854,1.104 4.104,1.323 0.25,0.219 10 true (3)
V100135

Bolt
V100136

Connector


Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


b.

Attach the clamp.


c.

Connect the 2 connectors.


d.
E317564

Install the 2 bolts.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 88510T 2.INSTALL REAR COOLING UNIT ASSEMBLY (for Manual Air Conditioning System)

a.

Install the rear cooling unit assembly with the 3 bolts and tighten the bolts in the order shown in the illustration.

E317566C01
1.073,2.135 1.313,2.354 0.24,0.219 10 true (1) 3.604,2.542 3.844,2.76 0.24,0.219 10 true (2) 3.833,1.104 4.073,1.323 0.24,0.219 10 true (3)
V100135

Bolt
V100136

Connector


Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


b.

Attach the clamp.


c.

Connect the 3 connectors.


d.
E317564

Install the 2 bolts.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 88716C 3.CONNECT COOLER REFRIGERANT LIQUID PIPE C

a.

Remove the vinyl tape from the cooler refrigerant liquid pipe C.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler refrigerant liquid pipe C.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the cooler refrigerant liquid pipe C.

NOTICE:

Keep the O-ring and O-ring fitting surfaces free of foreign matter.



d.
E317563

Connect the cooler refrigerant liquid pipe C.


e.

Install the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 88717A 4.CONNECT COOLER REFRIGERANT SUCTION PIPE A

a.

Remove the vinyl tape from the cooler refrigerant suction pipe A.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler refrigerant suction pipe A.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the cooler refrigerant suction pipe A.

NOTICE:

Keep the O-ring and O-ring fitting surfaces free of foreign matter.



d.
E317562

Connect the cooler refrigerant suction pipe A.


e.

Install the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 52159 5.INSTALL REAR BUMPER COVER

Hide 87201M 6.INSTALL NO. 5 AIR DUCT SUB-ASSEMBLY

a.
E317561C01
3.052,1.01 3.333,1.219 0.281,0.208 10 true (1) 1.333,0.417 1.615,0.625 0.281,0.208 10 true (2) 1.615,1.49 1.896,1.698 0.281,0.208 10 true (3)
V113147

Order of Installation


Install the No. 5 air duct sub-assembly as shown in the illustration.


b.
E317559

Install the 3 clips.


Hide 62471D 7.INSTALL REAR UPPER PILLAR GARNISH RH

Hide 73178B 8.INSTALL SEAT BELT ANCHOR COVER CAP

Hide 62638A 9.INSTALL QUARTER PILLAR GARNISH RH

Hide 73178C 10.INSTALL SEAT BELT ANCHOR COVER CAP

Hide 62511 11.INSTALL QUARTER INSIDE TRIM BOARD RH

Hide 73233B 12.INSTALL REAR NO. 2 SEAT LAP BELT OUTER ANCHOR COVER (w/ Rear No. 2 Seat)

Hide 73233A 13.INSTALL REAR NO. 1 SEAT LAP BELT OUTER ANCHOR COVER

Hide 67935 14.INSTALL BACK DOOR SCUFF PLATE

Hide 67917C 15.INSTALL REAR DOOR SCUFF PLATE RH

Hide 16.INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)

Hide 17.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT