A bolt without a torque specification is shown in the standard bolt chart.
Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS
63310
1.INSTALL ROOF HEADLINING ASSEMBLY
|
Movement Direction |
Insert the roof headlining assembly into the cabin from the back door.
Check that the corners of the roof headlining assembly are not folded, twisted or otherwise deformed and that none of the mounted parts have fallen off.
Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.
Do not damage the roof headlining assembly or vehicle interior.
Install the visor holder as shown in the illustration.
|
Install in this Direction |
Attach the claw to install the visor holder as shown in the illustration.
Use the same procedure for both visor holders.
Install the roof headlining assembly with the 2 clips.
Connect the front door opening trim weatherstrip LH and rear door opening trim weatherstrip LH in the range shown in the illustration.
| *1 | Front Door Opening Trim Weatherstrip LH | *2 | Rear Door Opening Trim Weatherstrip LH |
Connect the front door opening trim weatherstrip RH and rear door opening trim weatherstrip RH in the range shown in the illustration.
| *1 | Front Door Opening Trim Weatherstrip RH | *2 | Rear Door Opening Trim Weatherstrip RH |
Connect the connector to the rear pillar RH.
Connect the connector and attach the clamp to the front pillar RH.
Connect the connector and attach the clamp to the front pillar LH.
74620B
2.INSTALL REAR ASSIST GRIP ASSEMBLY
Use the same procedure for both rear assist grip assemblies.
Install the 2 clips and 2 assist grip covers to the rear assist grip.
Temporarily install the assist grip covers.
|
Install in this Direction |
Attach the clip.
Push in the assist grip covers to install the rear assist grip assembly.
74610A
3.INSTALL ASSIST GRIP SUB-ASSEMBLY
Use the same procedure for all assist grip sub-assemblies.
Install the 2 clips and 2 assist grip covers to the assist grip.
Temporarily install the assist grip covers.
|
Install in this Direction |
Attach the clip.
Push in the assist grip covers to install the assist grip sub-assembly.
74320
4.INSTALL VISOR ASSEMBLY LH
Install the visor assembly LH with the 2 screws.
When installing the visor assembly LH, make sure that the arrow on the back side of the visor bracket faces the front of the vehicle.
Connect the visor assembly LH to the visor holder.
74310
5.INSTALL VISOR ASSEMBLY RH
Install the visor assembly RH with the 2 screws.
When installing the visor assembly RH, make sure that the arrow on the back side of the visor bracket faces the front of the vehicle.
Connect the visor assembly RH to the visor holder.
74325
6.INSTALL VISOR BRACKET COVER LH
|
Install in this Direction |
Attach the claw to install the visor bracket cover LH as shown in the illustration.
74325
7.INSTALL VISOR BRACKET COVER RH
|
Install in this Direction |
Attach the claw to install the visor bracket cover RH as shown in the illustration.
73139C
8.INSTALL REAR SEAT BELT COVER
|
Install in this Direction |
Attach the guide.
Attach the clip and claw to install the rear seat belt cover as shown in the illustration.
81240
9.INSTALL NO. 1 ROOM LIGHT ASSEMBLY
81360T
10.INSTALL SPOT LIGHT ASSEMBLY
81260A
11.INSTALL MAP LIGHT ASSEMBLY
62472D
12.INSTALL UPPER REAR PILLAR GARNISH LH
|
Install in this Direction |
Attach the clip to install the upper rear pillar garnish LH as shown in the illustration.
Install the rear seat hook with the bolt.
Connect the rear No. 2 seat outer belt assembly LH with the bolt.
62471D
13.INSTALL UPPER REAR PILLAR GARNISH RH
|
Install in this Direction |
Attach the clip to install the upper rear pillar garnish RH as shown in the illustration.
Install the rear seat hook with the bolt.
Connect the rear No. 2 seat outer belt assembly RH with the bolt.
73178B
14.INSTALL SEAT BELT ANCHOR COVER CAP
Use the same procedure for seat belt anchor cover caps.
|
Install in this Direction |
Attach the claw to install the seat belt anchor cover cap as shown in the illustration.
62639A
15.INSTALL QUARTER PILLAR GARNISH LH
|
Install in this Direction |
Attach the clip to install the quarter pillar garnish LH as shown in the illustration.
| *1 | Rear Door Opening Trim Weatherstrip LH |
Connect the rear door opening trim weatherstrip LH in the range shown in the illustration.
Connect the rear No. 1 seat outer belt assembly LH with the bolt.
62638A
16.INSTALL QUARTER PILLAR GARNISH RH
|
Install in this Direction |
Attach the clip to install the quarter pillar garnish RH as shown in the illustration.
| *1 | Rear Door Opening Trim Weatherstrip RH |
Connect the rear door opening trim weatherstrip RH in the range shown in the illustration.
Connect the rear No. 1 seat outer belt assembly RH with the bolt.
73178B
17.INSTALL SEAT BELT ANCHOR COVER CAP
Use the same procedure for seat belt anchor cover caps.
|
Install in this Direction |
Attach the claw to install the seat belt anchor cover cap as shown in the illustration.
62512
18.INSTALL QUARTER INSIDE TRIM BOARD LH
|
Install in this Direction |
Attach the clip and claw to install the quarter inside trim board LH as shown in the illustration.
| *1 | Rear Door Opening Trim Weatherstrip LH |
Connect the rear door opening trim weatherstrip LH in the range shown in the illustration.
Connect the rear No. 2 seat outer belt assembly LH with the bolt.
Connect the rear No. 1 seat outer belt assembly LH with the bolt.
62511
19.INSTALL QUARTER INSIDE TRIM BOARD RH
Connect the connector.
|
Install in this Direction |
Attach the clip and claw to install the quarter inside trim board RH as shown in the illustration.
| *1 | Rear Door Opening Trim Weatherstrip RH |
Connect the rear door opening trim weatherstrip RH in the range shown in the illustration.
Connect the rear No. 2 seat outer belt assembly RH with the bolt.
Connect the rear No. 1 seat outer belt assembly RH with the bolt.
73233B
20.INSTALL REAR NO. 2 SEAT OUTER LAP BELT ANCHOR COVER
Use the same procedure for both rear No. 2 seat outer lap belt anchor covers.
|
Install in this Direction |
Attach the claw to install the rear No. 2 seat outer lap belt anchor cover as shown in the illustration.
73233A
21.INSTALL REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER
Use the same procedure for both rear No. 1 seat outer lap belt anchor covers.
|
Install in this Direction |
Attach the claw to install the rear No. 1 seat outer lap belt anchor cover as shown in the illustration.
67935
22.INSTALL BACK DOOR SCUFF PLATE
Attach the clip and claw to install the back door scuff plate as shown in the illustration.
|
Install in this Direction | - | - |
62412B
23.INSTALL UPPER CENTER PILLAR GARNISH LH
|
Install in this Direction |
Attach the clip to install the upper center pillar garnish LH as shown in the illustration.
| *1 | Front Door Opening Trim Weatherstrip LH |
| *2 | Rear Door Opening Trim Weatherstrip LH |
Connect the front door opening trim weatherstrip LH and rear door opening trim weatherstrip LH in the range shown in the illustration.
Connect the front seat outer belt assembly LH with the bolt.
62411B
24.INSTALL UPPER CENTER PILLAR GARNISH RH
|
Install in this Direction |
Attach the clip to install the upper center pillar garnish RH as shown in the illustration.
| *1 | Front Door Opening Trim Weatherstrip LH |
| *2 | Rear Door Opening Trim Weatherstrip LH |
Connect the front door opening trim weatherstrip RH and rear door opening trim weatherstrip RH in the range shown in the illustration.
Connect the front seat outer belt assembly RH with the bolt.
73178A
25.INSTALL SEAT BELT ANCHOR COVER CAP
Use the same procedure for both seat belt anchor cover caps.
|
Install in this Direction |
Attach the claw to install the seat belt anchor cover cap as shown in the illustration.
62414A
26.INSTALL LOWER CENTER PILLAR GARNISH LH
|
Install in this Direction |
Attach the clip and claw to install the lower center pillar garnish LH as shown in the illustration.
| *1 | Front Door Opening Trim Weatherstrip LH |
| *2 | Rear Door Opening Trim Weatherstrip LH |
Connect the front door opening trim weatherstrip LH and rear door opening trim weatherstrip LH in the range shown in the illustration.
Connect the front seat outer belt assembly LH with the bolt.
62413A
27.INSTALL LOWER CENTER PILLAR GARNISH RH
|
Install in this Direction |
Attach the clip and claw to install the lower center pillar garnish RH as shown in the illustration.
| *1 | Front Door Opening Trim Weatherstrip RH |
| *2 | Rear Door Opening Trim Weatherstrip RH |
Connect the front door opening trim weatherstrip RH and rear door opening trim weatherstrip RH in the range shown in the illustration.
Connect the front seat outer belt assembly RH with the bolt.
73233
28.INSTALL LAP BELT OUTER ANCHOR COVER
Use the same procedure for both outer lap belt anchor covers.
|
Install in this Direction |
Attach the claw to install the outer lap belt anchor cover as shown in the illustration.
67918E
29.INSTALL REAR DOOR SCUFF PLATE LH
|
Install in this Direction |
Attach the claw to install the rear door scuff plate LH as shown in the illustration.
Attach claw A shown in the illustration first.
67917C
30.INSTALL REAR DOOR SCUFF PLATE RH
|
Install in this Direction |
Attach the claw to install the rear door scuff plate RH as shown in the illustration.
Attach claw A shown in the illustration first.
67914B
31.INSTALL FRONT DOOR SCUFF PLATE LH
|
Install in this Direction |
Attach the claw to install the front door scuff plate LH as shown in the illustration.
Attach claw A shown in the illustration first.
67913B
32.INSTALL FRONT DOOR SCUFF PLATE RH
|
Install in this Direction |
Attach the claw to install the front door scuff plate RH as shown in the illustration.
Attach claw A shown in the illustration first.
62212
33.INSTALL FRONT PILLAR GARNISH LH
62211
34.INSTALL FRONT PILLAR GARNISH RH
74603
35.INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY
36.INSTALL REAR NO. 2 SEAT ASSEMBLY LH
37.INSTALL REAR NO. 2 SEAT ASSEMBLY RH
38.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
39.CHECK SRS WARNING LIGHT