Turn the ignition switch to ON.
Finish switching to L4.
Check the rear differential lock indicator light.
Press the differential lock switch.
After 60 seconds, check the rear differential lock indicator light.
| Result | Proceed to |
|---|---|
| Rear differential lock indicator light blinks or illuminates | A |
| Rear differential lock indicator light remains off regardless of switch operation | B |
| Rear differential lock indicator light remains illuminated regardless of switch operation | C |
| Rear differential lock indicator light rapidly blinks | D |
Blinking: Blinks at 0.5 second intervals (0.5 seconds on and 0.5 seconds off)
Rapidly blinking: Blinks at 0.25 second intervals (0.25 seconds on and 0.25 seconds off)
A
B
C
D
Select "Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN Bus.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSIS SYSTEM
"Bus Check" indicates no malfunctions in CAN communication.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the GTS on.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Four Wheel Drive / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Rear Differential Lock Control SW (R) | Differential lock switch status (differential lock switch input signal of R terminal on ECU side) | ON or OFF | ON: Switch pressed and held
OFF: Switch not pressed |
- |
| Tester Display |
|---|
| Rear Differential Lock Control SW (R) |
Display changes according to differential lock switch operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Perform Active Test of the combination meter assembly using the GTS.
| Tester Display |
|---|
| Indicat. Rr DIFF LOCK |
Check the combination meter assembly.
The rear differential lock indicator light turns on or off in accordance with the GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Remove the differential lock switch.
Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR DIFFERENTIAL LOCK CONTROL SWITCH>REMOVAL
Inspect the differential lock switch.
Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR DIFFERENTIAL LOCK CONTROL SWITCH>INSPECTION
The differential lock switch operates normally.
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the C60 4 wheel drive control ECU connector.
Disconnect the G58 differential lock switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C60-15 (R) - G58-6 (B) | Always | Below 1 Ω |
| G58-3 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Select "Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN Bus.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSIS SYSTEM
"Bus Check" indicates no malfunctions in CAN communication.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the GTS on.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Four Wheel Drive / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Rear Differential Lock Indicator Request | Rear differential lock indicator light request | Blink4*, Blink3, Blink2, Blink1, ON or OFF | ·
Blink3: Indicator light rapidly blinks ·
Blink2: Indicator light blinks 3 times ·
Blink1: Indicator light blinks ·
ON: Indicator light illuminates ·
OFF: Indicator light turns off |
·
Blinking: 0.5 second intervals (0.5 seconds on and 0.5 seconds off) ·
Rapidly blinking: 0.25 second intervals (0.25 seconds on and 0.25 seconds off) *: Item not supported, therefore not displayed |
| Tester Display |
|---|
| Rear Differential Lock Indicator Request |
Finish switching to L4.
Turn the differential lock switch on and off several times and check the GTS display condition of the rear differential lock indicator light.
| Result | Proceed to |
|---|---|
| Data List continues to display ON even when differential lock switch is operated | A |
| Data List display changes according to differential lock switch operation | B |
A
B
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING