Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD)
RM3270E _57 Power Source / Network _041704 NETWORKING _0201720 CAN COMMUNICATION SYSTEM(for RHD) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD)  Audio Receiver Assembly Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Audio Receiver Assembly Communication Stop Mode Either condition is met:
·

"Display and Navigation (AVN1)" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Audio Receiver Assembly Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source circuit of radio and display receiver assembly

·

Radio and display receiver assembly ground circuit

·

Radio and display receiver assembly CAN branch wire or connector

·

Radio and display receiver assembly



WIRING DIAGRAM

C280381E24
4.698,5.979 7.083,6.438 2.385,0.458 10 false Radio and Display Receiver Assembly 5.646,5.073 7,5.458 1.354,0.385 10 false GND1 5.646,4.25 7,4.635 1.354,0.385 10 false ACC1 5.646,3.438 7,3.823 1.354,0.385 10 false IG 5.646,2.583 7,2.969 1.354,0.385 10 false +B1 5.646,1.438 7,1.823 1.354,0.385 10 false CANL 5.656,0.833 7.01,1.219 1.354,0.385 10 false CANH 1.677,0.698 3.031,1.083 1.354,0.385 10 false 1 1.677,1.292 2.104,1.656 0.427,0.365 10 false 2 0.229,1.729 0.969,2.115 0.74,0.385 10 false G126 0.229,1.906 2.604,2.188 2.375,0.281 10 false No. 2 CAN Junction Connector 2.115,2.594 3.469,2.979 1.354,0.385 10 false from Battery 0.354,3.417 2.885,3.625 2.531,0.208 10 false from IG1 NO.1 Relay*1, Ignition Switch*2 1.865,4.24 3.219,4.625 1.354,0.385 10 false from ACC Relay 4.135,4.063 5.49,4.448 1.354,0.385 10 false ACC 3.979,3.24 5.333,3.625 1.354,0.385 10 false IG1 NO.4 4.073,2.417 4.99,2.833 0.917,0.417 10 false RADIO 5.115,2.583 6.031,3 0.917,0.417 10 false G102 5.125,0.813 6.042,1.229 0.917,0.417 10 false G100 5.188,1.146 6.542,1.531 1.354,0.385 10 false 10 5.24,0.563 6.594,0.948 1.354,0.385 10 false 9 5.229,2.323 6.583,2.708 1.354,0.385 10 false 4 5.219,3.167 6.573,3.552 1.354,0.385 10 false 1 5.219,3.99 6.573,4.375 1.354,0.385 10 false 3 5.229,4.781 6.583,5.167 1.354,0.385 10 false 7 0.396,5.927 3.5,6.229 3.104,0.302 10 false *2: w/o Smart Entry and Start System 0.396,5.51 3.792,5.958 3.396,0.448 10 false *1: w/ Smart Entry and Start System 5.115,1.396 6.031,1.813 0.917,0.417 10 false G100 5.115,3.406 6.031,3.823 0.917,0.417 10 false G100 5.115,4.208 6.031,4.625 0.917,0.417 10 false G102 5.115,5.042 6.031,5.458 0.917,0.417 10 false G102

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 3 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY CAN BRANCH WIRE)
a.
C310966C12
1.49,0.198 1.938,0.469 0.448,0.271 1.104,1.75 1.271,1.75 1.271,1.75 1.896,1.104 true 2.354,1.771 2.208,1.771 2.208,1.771 2.01,1.125 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 1.563,0.24 2.188,0.615 0.625,0.375 10 false G100 0.677,1.677 1.292,1.875 0.615,0.198 10 false CANH 2.438,1.698 3.052,1.896 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G100-9 (CANH) - G100-10 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
C277477C26
1.5,0.208 1.99,0.458 0.49,0.25 1.51,1.813 2.01,2.063 0.5,0.25 0.979,2.604 0.74,2.281 0.74,2.281 0.573,2.281 true 2.104,1.479 1.854,1.479 1.854,1.479 1.667,1.146 true 2.573,0.708 2.375,0.708 2.375,0.708 2.198,0.896 true 2.438,0.396 2.24,0.396 2.24,0.396 2,0.885 true 0.365,2.188 0.719,2.5 0.354,0.313 10 false IG 2.146,1.396 2.688,1.625 0.542,0.229 10 false GND1 0.125,0.135 0.583,0.333 0.458,0.198 10 false *a 1.573,0.229 2.125,0.573 0.552,0.344 10 false G102 1.594,1.823 2.052,2.104 0.458,0.281 10 false G100 2.615,0.604 3.156,0.833 0.542,0.229 10 false +B1 2.5,0.292 3.042,0.521 0.542,0.229 10 false ACC1
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Disconnect the radio and display receiver assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G102-4 (+B1) - Body ground Always 11 to 14 V
G100-1 (IG) - Body ground Ignition switch ON 11 to 14 V
G102-3 (ACC1) - Body ground Ignition switch ACC 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G102-7 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR