Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2015.08–2016.01
RM3270E _58 Vehicle Interior _041708 METER / GAUGE / DISPLAY _0203147 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Engine Coolant Temperature Gauge Malfunction  


DESCRIPTION

In this circuit, the combination meter assembly receives engine coolant temperature signals from the ECM via the CAN communication system. The combination meter assembly displays the engine coolant temperature that is calculated based on the data received from the ECM.

WIRING DIAGRAM

E255800E11
4.74,2.563 6.958,2.813 2.219,0.25 10 false Combination Meter Assembly 1.729,2.542 3.958,2.99 2.229,0.448 10 false ECM 0.802,3.375 3.563,3.656 2.76,0.281 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, make sure to replace it with a new one.

·

If there is an open or short in the engine coolant temperature sensor circuit, the ECM stores DTCs. Troubleshoot the ECD system.

Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed.



PROCEDURE

1.CHECK FOR DTC (CAN COMMUNICATION SYSTEM)

Result:
Result
OK
NG



OK

2.CHECK FOR DTC (ECD SYSTEM)

NG

2.CHECK FOR DTC (ECD SYSTEM)
a.

Check for DTCs.

Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
OK:

No DTCs are output.



Result:
Result
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (WATER TEMPERATURE METER OPERATION)

NG

3.PERFORM ACTIVE TEST USING GTS (WATER TEMPERATURE METER OPERATION)
a.

Using the GTS, perform the Active Test.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Water Temperature Meter Operation Engine coolant temperature receiver gauge OFF, LOW, NORMAL, HIGH -
Body Electrical > Combination Meter > Active Test
Tester Display
Water Temperature Meter Operation
50004 122 89
OK:

Engine coolant temperature receiver gauge indication is normal.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (COOLANT TEMP, COOLANT TEMPERATURE)

NG

REPLACE COMBINATION METER ASSEMBLY

4.READ VALUE USING GTS (COOLANT TEMP, COOLANT TEMPERATURE)
a.

Using the GTS, read the Data List.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Normal Condition Reference Value Diagnostic Note
Coolant Temp Engine coolant temperature Min.: -40°C (-40°F), Max: 215°C (419°F) 75 to 100°C (167 to 212°F): After warming up the engine -
Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Coolant Temperature Engine coolant temperature Min.: 0°C (0°F), Max.: 127.5°C (261.5°F) 75 to 100°C (167 to 212°F): After warming up the engine -
Powertrain > Engine and ECT > Data List
Tester Display
Coolant Temp
50003 234 8
Body Electrical > Combination Meter > Data List
Tester Display
Coolant Temperature
50003 122 10
HINT:
·

When the Data List values of the ECUs match, an internal malfunction of the ECM is suspected.

·

When the Data List values of the ECUs do not match, a signal output error of the ECM or an internal malfunction of the combination meter assembly is suspected.



OK:

The Data List values of the ECUs do not match.



Result:
Result
OK
NG



OK

5.CHECK COMBINATION METER ASSEMBLY

NG

5.CHECK COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly with a new one.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Check that the operation of the engine coolant temperature receiver gauge returns to normal.

OK:

The operation of the engine coolant temperature receiver gauge returns to normal.



Result:
Result
OK
NG



OK

END (COMBINATION METER ASSEMBLY IS DEFECTIVE)

NG