Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK › 2015.08–2016.01
RM3270E _58 Vehicle Interior _041705 DOOR LOCK _0205680 FRONT DOOR LOCK A

DOOR LOCK  FRONT DOOR LOCK  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the RH side.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 69318C 1.INSTALL DOOR LOCK WIRING HARNESS SEAL

NOTICE:
·

Do not allow grease or dust to adhere to the door lock wiring harness seal installation surface.

·

Reusing a door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water ingress. This may result in a malfunction of the front door lock assembly RH.

·

When reusing a removed front door lock assembly RH, replace the door lock wiring harness seal with a new one.



a.
B404281C01
0,0 0,0 false
V113147

Install in this Direction


Install a new door lock wiring harness seal to the front door lock assembly RH.


Hide 69710B 2.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY RH

a.
B404285C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide to install the front door lock remote control cable assembly RH to the front door lock assembly RH.


Hide 69750C 3.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY RH

a.
B404282C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide to install the front door inside locking cable assembly RH to the front door lock assembly RH.


Hide 69035A 4.INSTALL FRONT DOOR LOCK COVER SUB-ASSEMBLY RH

a.
B404255

Attach the clamp and claw to install the front door lock cover sub-assembly RH.


Hide 69310 5.INSTALL FRONT DOOR LOCK ASSEMBLY RH

a.

Apply MP grease to the sliding parts of the front door lock assembly RH.


b.
B404286C01
1.698,0.75 1.865,0.26 1.865,0.26 2.135,0.26 true 2.115,0.188 2.344,0.417 0.229,0.229 10 true *1
*1 Front Door Lock Open Rod RH
V113147

Install in this Direction


Connect the front door lock open rod RH to install the front door lock assembly RH as shown in the illustration.

HINT:

Make sure that the front door lock open rod RH is securely connected to the front door lock assembly RH.



c.
B404253C04
0,0 0,0 false
V100135

"Torx" Screw
V100136

Connector


Using a T30 "TORX" socket wrench, install the front door lock assembly RH with the 3 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


d.

Connect the connector.


Hide 6.INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)

Hide 67403F 7.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY RH

Hide 68101 8.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY RH

Hide 68141C 9.INSTALL FRONT DOOR GLASS RUN RH

Hide 67831 10.INSTALL FRONT DOOR SERVICE HOLE COVER RH

Hide 67601 11.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY RH

Hide 69283 12.INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG RH

Hide 13.INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

Hide 14.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

Hide 74210 15.INSTALL FRONT ARMREST ASSEMBLY RH

Hide 67491A 16.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH RH

Hide 17.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION