Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK › 2015.08–2016.01
RM3270E _58 Vehicle Interior _041705 DOOR LOCK _0205681 REAR DOOR LOCK A

DOOR LOCK  REAR DOOR LOCK  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the RH side.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 69318D 1.INSTALL DOOR LOCK WIRING HARNESS SEAL

NOTICE:
·

Do not allow grease or dust to adhere to the door lock wiring harness seal installation surface.

·

Reusing a door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water ingress. This may result in a malfunction of the rear door lock assembly.

·

When reusing a removed rear door lock assembly, replace the door lock wiring harness seal with a new one.



a.
B404327

Install a new door lock wiring harness seal to the rear door lock assembly RH.


Hide 69770B 2.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY RH

a.
B404346C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide to install the rear door inside locking cable assembly RH to the rear door lock assembly RH.


Hide 69730D 3.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY RH

a.
B404347C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide to install the rear door lock remote control cable assembly RH to the rear door lock assembly RH.


Hide 69037 4.INSTALL REAR DOOR LOCK COVER SUB-ASSEMBLY RH

a.
B404324

Attach the clamp and claw to install the rear door lock cover sub-assembly RH.


Hide 69330 5.INSTALL REAR DOOR LOCK ASSEMBLY RH

a.

Apply MP grease to the sliding parts of the rear door lock assembly RH.


b.
B408899C01
0.542,2.271 0.708,2.104 0.708,2.104 1.063,2.094 true 1.094,2.01 1.333,2.219 0.24,0.208 10 true *a
*a Release Plate
V100135

"Torx" Screw
V100136

Connector
V113147

Install in this Direction


Insert the rear door lock assembly RH into the rear door outside handle frame sub-assembly RH release plate, and set it to the rear door panel RH.

HINT:

Make sure that the rear door outside handle frame sub-assembly RH release plate is securely connected to the rear door lock assembly RH.



c.

Using a T30 "TORX" socket wrench, install the rear door lock assembly RH with the 3 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


d.

Connect the connector.


Hide 67836 6.INSTALL REAR DOOR LOCK CHILD PROTECTION COVER RH

Hide 68103 7.INSTALL REAR DOOR GLASS SUB-ASSEMBLY RH

Hide 67407E 8.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY RH

Hide 68142C 9.INSTALL REAR DOOR GLASS RUN RH

Hide 67841E 10.INSTALL REAR DOOR SERVICE HOLE COVER RH

Hide 67603 11.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY RH

Hide 69283A 12.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG RH

Hide 13.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

Hide 74250 14.INSTALL REAR ARMREST ASSEMBLY RH

Hide 67673A 15.INSTALL REAR DOOR FRAME GARNISH RH

Hide 16.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION