Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR › 2015.08–2016.01
RM3270E _59 Vehicle Exterior _041717 DOOR / HATCH _0205103 REAR DOOR A

DOOR / HATCH  REAR DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the RH side.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 75925C 2.INSTALL NO. 3 BLACK OUT TAPE RH

HINT:

The procedure described below is for the LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>BLACK OUT TAPE(for Rear Door)>INSTALLATION


Hide 75923C 3.INSTALL NO. 2 BLACK OUT TAPE RH

HINT:

The procedure described below is for the LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>BLACK OUT TAPE(for Rear Door)>INSTALLATION


Hide 67837C 4.INSTALL REAR DOOR DUST PROOF SEAL

a.
B409006

Attach the claw to install 3 new rear door dust proof seals.


Hide 67871 5.INSTALL REAR DOOR WEATHERSTRIP RH

a.
B409005C02
0,0 0,0 false
V100155

Double-sided Tape


Attach the clip to install a new rear door weatherstrip RH.


b.

Remove the peeling paper from double-sided tape and press the double-sided tape to the rear door panel RH.


Hide 68630D 6.INSTALL REAR DOOR CHECK ASSEMBLY RH

a.

Apply MP grease to the sliding area of the rear door check assembly RH.


b.

When reusing a bolt:

i.

Clean the threads of the bolt (B) with non-residue solvent.


ii.

Apply adhesive to the threads of the bolt (B).

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.




c.
B408773C02
0,0 0,0 false
V100135

Bolt (A)
V100136

Bolt (B)


Install the rear door check assembly RH with the 2 bolts (A) and bolt (B).

Torque:
Bolt (A) : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Bolt (B) : 30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 67003C 7.INSTALL REAR DOOR PANEL CUSHION

a.
B408772

Attach the claw to install 2 new rear door panel cushions.


Hide 69203A 8.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY RH

a.

Apply MP grease to the sliding area of the rear door outside handle frame sub-assembly RH.


b.
B408770C02
2.188,0.604 2.188,0.24 2.188,0.24 2.365,0.24 true 1.063,0.854 1.063,1.073 1.063,1.073 1.313,1.073 true 1.063,0.521 1.063,0.24 1.063,0.24 1.292,0.24 true 2.333,0.167 2.604,0.438 0.271,0.271 10 true *a 1.25,0.156 1.479,0.354 0.229,0.198 10 true *b 1.219,0.979 1.448,1.177 0.229,0.198 10 true *b
*a Grommet
*b Guide
V113147

Install in this Direction


Attach the grommet and guide to install the rear door outside handle frame sub-assembly RH as shown in the illustration.


c.

Using a T30 "TORX" socket wrench, install the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69242G 9.INSTALL REAR DOOR REAR OUTSIDE HANDLE PAD

a.
B408769C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw to install the rear door rear outside handle pad.


Hide 69241G 10.INSTALL REAR DOOR FRONT OUTSIDE HANDLE PAD

a.
B408767C02
0,0 0,0 false
V113147

Install in this Direction


Attach the claw to install the rear door front outside handle pad.


Hide 69230 11.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY RH

a.
B408765C01
0,0 0,0 false
V113147

Install in this Direction


Install the rear door outside handle assembly RH as shown in the illustration.


Hide 69227M 12.INSTALL REAR DOOR OUTSIDE HANDLE COVER

a.
B408763C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw to install the rear door outside handle cover as shown in the illustration.


b.

Using a T30 "TORX" socket wrench, install the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69318D 13.INSTALL DOOR LOCK WIRING HARNESS SEAL

Hide 69730D 14.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY RH

Hide 69770B 15.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY RH

Hide 69037 16.INSTALL REAR DOOR LOCK COVER SUB-ASSEMBLY RH

Hide 69330 17.INSTALL REAR DOOR LOCK ASSEMBLY RH

Hide 67836 18.INSTALL REAR DOOR LOCK CHILD PROTECTION COVER RH

a.
B408753

Install the rear door lock child protection cover RH.


Hide 85710F 19.INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

Hide 69803 20.INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY RH

a.

Apply MP grease to the sliding area of the rear door window regulator sub-assembly RH.


b.

Temporarily install the temporarily bolt to the rear door window regulator sub-assembly RH.


c.
B408752C02
0,0 0,0 false
V100135

Bolt
V100136

Connector
V100137

Temporarily Bolt


Install the rear door window regulator sub-assembly RH with the 3 bolts and temporary bolt.

Torque:
Bolt : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Temporarily Bolt : 8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

Be careful not to drop the rear door window regulator sub-assembly RH as it may become damaged.



d.

Connect the connector.


Hide 75730 21.INSTALL REAR DOOR BELT MOULDING ASSEMBLY RH

HINT:

The procedure described below is for the LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>REAR DOOR BELT MOULDING>INSTALLATION


Hide 75723 22.INSTALL REAR DOOR REAR BELT MOULDING RH

HINT:

The procedure described below is for the LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>REAR DOOR BELT MOULDING>INSTALLATION


Hide 68188 23.INSTALL REAR DOOR QUARTER WINDOW WEATHERSTRIP RH

a.
B408751

Install the rear door quarter window weatherstrip RH to the rear door quarter window glass RH.


Hide 68123B 24.INSTALL REAR DOOR QUARTER WINDOW GLASS RH

a.
B408750C01
0,0 0,0 false
V113147

Install in this Direction


Install the rear door quarter window glass RH together with the rear door quarter window weatherstrip RH.


Hide 68103 25.INSTALL REAR DOOR GLASS SUB-ASSEMBLY RH

a.
B408747C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Insert the rear door glass sub-assembly RH as shown in the illustration.


b.
B408748

Install the rear door glass sub-assembly RH to the rear door window regulator sub-assembly RH as shown in the illustration.

NOTICE:

Be careful not to damage the rear door glass sub-assembly RH.



Hide 67407E 26.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY RH

a.
B408744C02
0,0 0,0 false
V100135

Bolt
V100136

Screw


Lift up the rear door weatherstrip RH and install the screw.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


b.

Install the rear door window division bar sub-assembly RH with the 2 bolts.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


Hide 68142C 27.INSTALL REAR DOOR GLASS RUN RH

a.
B408743

Attach the guide to install a new rear door glass run RH.


Hide 28.INSTALL SCREW GROMMET

a.
B408742

Attach the claw to install 2 new screw grommets.


Hide 67841E 29.INSTALL REAR DOOR SERVICE HOLE COVER RH

a.

Apply new butyl tape to the rear door panel.


b.
B408741C01
2.667,0.448 2.667,0.219 2.667,0.219 2.865,0.219 true 0.698,0.448 0.698,0.219 0.698,0.219 0.896,0.219 true 0.896,0.094 1.125,0.313 0.229,0.219 10 true *a 2.823,0.125 3.052,0.344 0.229,0.219 10 true *a
*a Reference Point
V100143

Butyl Tape


Pass the rear door inside locking cable assembly RH and rear door lock remote control cable assembly RH through a new rear door service hole cover RH, and then attach the rear door service hole cover RH using the reference points on the rear door panel.

HINT:
·

Securely install the rear door service hole cover RH to prevent wrinkles and air bubbles.

·

There should be no wrinkles or folds after installing the rear door service hole cover RH.

·

After installing the rear door service hole cover RH, check the seal quality.




Hide 86160B 30.INSTALL REAR SPEAKER ASSEMBLY

Hide 68173B 31.INSTALL REAR DOOR INNER GLASS WEATHERSTRIP RH

a.
B408739C01
0,0 0,0 false
V113147

Install in this Direction


Install a new rear door inner glass weatherstrip RH to the rear door trim board sub-assembly RH and fold down the claw in the directions indicated by the arrows in the illustration.


Hide 69205A 32.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY RH

a.
B408737C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw to install the rear door inside handle sub-assembly RH to the rear door trim board sub-assembly RH.


Hide 67603 33.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY RH

a.
B409015C01
1.177,0.917 1.479,0.552 1.479,0.552 1.833,0.552 true 1.198,1.333 1.542,1.771 1.542,1.771 1.958,1.771 true 1.781,0.458 2.021,0.667 0.24,0.208 10 true *1 1.823,1.708 2.063,1.917 0.24,0.208 10 true *2
*1 Rear Door Inside Locking Cable Assembly RH
*2 Rear Door Lock Remote Control Cable assembly RH
V113147

Install in this Direction


Attach the clamp to connect the rear door lock remote control cable assembly RH and rear door inside locking cable assembly RH as shown in the illustration.


b.
B408735C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide as shown in the illustration.


c.
B408733

Attach the clip to install the rear door trim board sub-assembly RH.


d.
B408731

Install the 3 screws.


Hide 69283A 34.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG RH

a.
B408730

Attach the claw to install the rear door inside handle bezel plug RH.


Hide 67665D 35.INSTALL REAR DOOR TRIM REFLECTOR RH (w/ Reflex Reflector Assembly)

a.
B405482C01
0.104,0.083 0.417,0.281 0.313,0.198 10 true *A 0.135,2.344 0.448,2.542 0.313,0.198 10 true *B
*A for RH Side
*B for LH Side
V100155

Protective Tape
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Attach the guide and claw to install the rear door trim reflector RH as shown in the illustration.


b.

Remove the protective tape.


Hide 81230 36.INSTALL COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

Hide 84810D 37.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY

Hide 38.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

a.

Connect the connector.


b.
B408728C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and clip to install the rear power window regulator switch assembly with rear door armrest base panel as shown in the illustration.


Hide 74250 39.INSTALL REAR ARMREST ASSEMBLY RH

a.
B408726C01
0,0 0,0 false
V100135

Order of Installation
V113147

Install in this Direction


Attach the claw and clip to install the rear armrest assembly RH.


Hide 67673A 40.INSTALL REAR DOOR FRAME GARNISH RH

a.
B408724

Attach the clip and claw to install the rear door frame garnish RH.


Hide 41.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION