Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY › 2015.08–2016.01
RM3270E _58 Vehicle Interior _041712 SEAT BELT _0206029 FRONT SEAT OUTER BELT ASSEMBLY A

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front seat outer belt assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Disconnect cable from negative battery terminal w/ Power Back Door System:
Reset back door close position
Power back door system (Click here)

CAUTION:
B394719

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the RH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 67913B 3.REMOVE FRONT DOOR SCUFF PLATE RH

Hide 67917C 4.REMOVE REAR DOOR SCUFF PLATE RH

Hide 73233 5.REMOVE OUTER LAP BELT ANCHOR COVER

Hide 73210 6.REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH (Floor Anchor)

a.
B404832

Remove the bolt and disconnect the floor anchor of the front seat outer belt assembly RH.


Hide 62413A 7.REMOVE LOWER CENTER PILLAR GARNISH RH

Hide 73178A 8.REMOVE SEAT BELT ANCHOR COVER CAP

Hide 73210 9.REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH

a.
B404836

Remove the bolt and disconnect the shoulder anchor of the front seat outer belt assembly RH.


b.
B404837C01
1.021,0.448 1.438,0.302 true 1.531,0.24 1.844,0.438 0.313,0.198 10 false *1
*1 Locking Button
V100155

Protective Tape


Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector as shown in the illustration.

HINT:

Tape the screwdriver tip before use.



c.
B404838

Remove the bolt.


d.

Detach the 2 guides and remove the front seat outer belt assembly RH.


Hide 62411B 10.REMOVE UPPER CENTER PILLAR GARNISH RH

Hide 73023 11.REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

HINT:

Perform this procedure when replacing the shoulder belt anchor plate sub-assembly RH.


a.
B404841C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claw and remove the front shoulder belt anchor plate sub-assembly RH in the illustration.


Hide 73135A 12.REMOVE SHOULDER BELT ANCHOR COVER RH

HINT:

Perform this procedure when replacing the shoulder belt anchor cover RH.


a.
B409156C01
1.729,1.344 2.365,1.521 2.365,1.521 1.75,1.938 true 2.438,1.448 2.75,1.604 0.313,0.156 10 false *1
*1 Shoulder Belt Anchor Cover RH


Detach the claw and remove the 2 shoulder belt anchor cover RH.


Hide 73200A 13.REMOVE FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

a.
B404843

Remove the 2 bolts.


b.

Detach the guide to remove the front shoulder belt anchor adjuster assembly.