Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function) › 2015.08–2016.01
RM3270E _58 Vehicle Interior _041706 THEFT DETERRENT / KEYLESS ENTRY _0212879 SMART ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  Back Door Entry Unlock Function does not Operate  


DESCRIPTION

If the entry unlock function does not operate for the back door only, but the entry lock function operates, the request code is being transmitted properly from the back door. In this case, there may be a problem related to the unlock switch (connection between the back door opener switch assembly and certification ECU (smart key ECU assembly)).

WIRING DIAGRAM

B345013E05
3.729,1.729 4.115,1.917 0.385,0.188 10 false RDA3 3.031,2.521 4.615,2.938 1.583,0.417 10 false Certification ECU (Smart Key ECU Assembly) 5.531,1.229 5.917,1.417 0.385,0.188 10 false PRG 5.531,1.729 5.917,1.917 0.385,0.188 10 false RDA 5.469,2.667 6.521,2.938 1.052,0.271 10 false Body ECU 0.802,1.75 1.188,1.938 0.385,0.188 10 false V10 4.198,1.708 4.583,1.896 0.385,0.188 10 false G17 5.479,2.49 5.865,2.677 0.385,0.188 10 false G33 0.802,1.917 1.969,2.354 1.167,0.438 10 false Back Door Opener Switch Assembly 2,0.906 2.385,1.094 0.385,0.188 10 false 3 4.198,1.219 4.583,1.406 0.385,0.188 10 false G17 2.99,1.01 3.375,1.198 0.385,0.188 10 false G16 2.99,1.438 3.375,1.625 0.385,0.188 10 false G16 2.99,1.958 3.375,2.146 0.385,0.188 10 false G16 3.031,0.813 3.281,1 0.25,0.188 10 false 14 3.031,1.25 3.281,1.438 0.25,0.188 10 false 23 3.031,1.76 3.281,1.948 0.25,0.188 10 false 10 4.229,1.031 4.479,1.219 0.25,0.188 10 false 36 4.229,1.51 4.479,1.698 0.25,0.188 10 false 13 5.313,1.104 5.563,1.292 0.25,0.188 10 false 9 5.24,1.594 5.49,1.781 0.25,0.188 10 false 16 2,1.333 2.385,1.521 0.385,0.188 10 false 1 0.667,1.333 1.052,1.521 0.385,0.188 10 false 2 3.313,1 3.76,1.188 0.448,0.188 10 false TSW5 3.729,1.229 4.177,1.417 0.448,0.188 10 false PRG3 3.333,1.958 3.698,2.146 0.365,0.188 10 false E 3.313,1.438 3.76,1.625 0.448,0.188 10 false TSW6 1.76,1.344 2.146,1.531 0.385,0.188 10 false L 0.875,1.333 1.26,1.521 0.385,0.188 10 false E 1.708,0.927 2.094,1.115 0.385,0.188 10 false UL

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN).

While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) or B27B0 is not output.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

If the body ECU has been replaced, it is necessary to initialize the body ECU.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the power window regulator master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Door locks operate normally.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (TR/B-DOOR UNLOCK SW)

NG

2.READ VALUE USING GTS (TR/B-DOOR UNLOCK SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry & Start / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tr/B-Door Unlock SW Back door opener switch assembly (open switch) ON or OFF ON: Back door opener switch assembly (open switch) pressed
OFF: Back door opener switch assembly (open switch) not pressed
·

Displays whether the back door opener switch assembly (open switch) is on or off.

·

Use this Data List item to help determine if there is a switch malfunction when the back door open function does not operate.


Body Electrical > Entry&Start > Data List
Tester Display
Tr/B-Door Unlock SW
50003 125 17
OK:

The GTS display changes correctly in response to the operation of the back door opener switch assembly.



Result:
Result Proceed to
NG A
OK B



A

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BACK DOOR OPENER SWITCH ASSEMBLY)

B

5.CHECK ENTRY BACK DOOR UNLOCK OPERATION
3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BACK DOOR OPENER SWITCH ASSEMBLY)
a.

Disconnect the G16 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the V10 back door opener switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-14 (TSW5) - V10-3 (UL) Always Below 1 Ω
G16-10 (E) - Body ground Always Below 1 Ω
V10-2 (E) - Body ground Always Below 1 Ω
G16-14 (TSW5) or V10-3 (UL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY
a.

Inspect the back door opener switch assembly.

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR OPENER SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK ENTRY BACK DOOR UNLOCK OPERATION

NG

REPLACE BACK DOOR OPENER SWITCH ASSEMBLY

5.CHECK ENTRY BACK DOOR UNLOCK OPERATION
a.

Check the entry back door unlock operation.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

HINT:

Disconnect and reconnect the connectors of certification ECU (smart key ECU assembly) and back door opener switch assembly before performing the inspection.


OK:

Entry back door unlock operates normally.



Result:
Proceed to
OK
NG



OK

END (CONNECT CONNECTORS PROPERLY)

NG

6.REPLACE BODY ECU
6.REPLACE BODY ECU
a.

Replace the body ECU with a new or known good one.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK ENTRY BACK DOOR UNLOCK OPERATION
7.CHECK ENTRY BACK DOOR UNLOCK OPERATION
a.

Check the entry back door unlock operation.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

OK:

Entry back door unlock operates normally.



Result:
Proceed to
OK
NG



OK

END (BODY ECU WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)