Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2015.08–2016.01
RM3270E _54 Brake _041691 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0213502 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Downhill Assist Control Indicator Light Remains ON  


DESCRIPTION

When the downhill assist control switch is turned on, the downhill assist control function is available and the downhill assist control indicator light illuminates.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSIS SYSTEM


Result:
Proceed to
DTC is not output
DTC is output



DTC is not output

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

DTC is output

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.INSPECT DOWNHILL ASSIST CONTROL SWITCH

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.INSPECT DOWNHILL ASSIST CONTROL SWITCH
a.

Turn the ignition switch off.


b.

c.

Inspect the downhill assist control switch.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>DOWNHILL ASSIST CONTROL SWITCH>INSPECTION

OK:

The downhill assist control switch operates normally.



Result:
Result
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - DOWNHILL ASSIST CONTROL SWITCH)

NG

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - DOWNHILL ASSIST CONTROL SWITCH)
a.

Disconnect the A4 skid control ECU (brake actuator assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A4-27 (HDCS) - G24-4 Always Below 1 Ω
A4-27 (HDCS) or G24-4 - Body ground Always 10 kΩ or higher
G24-1 - Body ground Always Below 1 Ω


Result:
Result
OK
NG




OK

5.READ VALUE USING GTS (DOWNHILL ASSIST CONTROL LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ VALUE USING GTS (DOWNHILL ASSIST CONTROL LIGHT)
a.

Reconnect the A4 skid control ECU (brake actuator assembly) connector.


b.

Reconnect the G24 downhill assist control switch connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


g.

According to the display on the GTS, read the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Downhill Assist Control Light Downhill assist control indicator light ON or OFF OFF: Downhill assist control indicator light off
ON: Downhill assist control indicator light on
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Downhill Assist Control Light
50003 105 59

h.

Check the GTS display condition of the Downhill assist control indicator light.

Result:
Proceed to
Display of the Data List remains OFF
Display of the Data List remains ON




Display of the Data List remains OFF

Display of the Data List remains ON