Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM
RM3270E _58 Vehicle Interior _041712 SEAT BELT _0214119 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Rear Seat Belt Warning Light Malfunction  


DESCRIPTION

The combination meter assembly detects whether either rear door is open or closed based on the condition of the left and right courtesy light switches. The combination meter assembly detects the rear seat belt state. The rear seat belt warning lights on the telltale light assembly illuminate or turn off in accordance with the rear door state, vehicle speed and rear seat belt state.

WIRING DIAGRAM

E336502E07
0.656,2.958 1.115,3.156 0.458,0.198 10 false CPU 1.24,3.052 1.698,3.25 0.458,0.198 10 false I/F 2.323,1.719 2.781,1.917 0.458,0.198 10 false G27 2.333,1.875 5.854,2.073 3.521,0.198 10 false Telltale Light Assembly 1.563,2.292 2.177,2.49 0.615,0.198 10 false RRBT 1.542,3.344 2.156,3.542 0.615,0.198 10 false RLBT 1.542,3.979 2.156,4.177 0.615,0.198 10 false RCSB 2.906,4.698 3.365,4.896 0.458,0.198 10 false N44 2.896,4.854 4.583,5.208 1.688,0.354 10 false Rear Center Seat Lap Type Belt Assembly LH 5,4.75 6.688,5.104 1.688,0.354 10 false Rear Center Seat Lap Type Belt Assembly RH 3.219,3.354 3.833,3.552 0.615,0.198 10 false LBR+ 4.406,3.333 5.021,3.531 0.615,0.198 10 false LBR- 3.198,3.979 3.813,4.177 0.615,0.198 10 false CBR+ 3.208,4.427 3.823,4.625 0.615,0.198 10 false CBR- 2.063,3.104 2.219,3.302 0.156,0.198 10 false 7 3,3.094 3.156,3.292 0.156,0.198 10 false 1 4.896,3.094 5.052,3.292 0.156,0.198 10 false 2 2.083,3.74 2.24,3.938 0.156,0.198 10 false 6 2.99,3.729 3.146,3.927 0.156,0.198 10 false 3 4.885,3.719 5.042,3.917 0.156,0.198 10 false 3 4.885,4.208 5.042,4.406 0.156,0.198 10 false 4 3,4.208 3.156,4.406 0.156,0.198 10 false 4 0.333,7.5 0.792,7.698 0.458,0.198 10 false G9 0.333,7.667 4.313,7.865 3.979,0.198 10 false Combination Meter Assembly 0.063,8.042 5.417,8.24 5.354,0.198 10 false *1: w/ Smart Entry and Start System 0.063,8.406 5.417,8.604 5.354,0.198 10 false *2: w/o Smart Entry and Start System 1.521,5.906 2.135,6.104 0.615,0.198 10 false RRCY 1.542,7.021 2.156,7.219 0.615,0.198 10 false RLCY 1.531,0.531 2.146,0.729 0.615,0.198 10 false RLMT 1.531,0.948 2.146,1.146 0.615,0.198 10 false RCMT 1.521,1.396 2.135,1.594 0.615,0.198 10 false RRMT 2.688,1.542 3.302,1.74 0.615,0.198 10 false RRID 2.698,1.146 3.313,1.344 0.615,0.198 10 false RCID 2.698,0.708 3.313,0.906 0.615,0.198 10 false RLID 3.854,0.688 5.083,0.885 1.229,0.198 10 false IG1 NO.4 3.271,0.688 3.729,0.885 0.458,0.198 10 false IG+ 2.031,0.406 2.344,0.604 0.313,0.198 10 false 24 2.031,0.844 2.344,1.042 0.313,0.198 10 false 23 2.031,1.271 2.344,1.469 0.313,0.198 10 false 22 2.042,2.031 2.198,2.229 0.156,0.198 10 false 5 2.083,5.771 2.396,5.969 0.313,0.198 10 false 18 2.083,6.906 2.396,7.104 0.313,0.198 10 false 17 3.625,0.438 3.938,0.635 0.313,0.198 10 false 10 2.427,0.427 2.583,0.625 0.156,0.198 10 false 1 2.438,0.854 2.594,1.052 0.156,0.198 10 false 2 2.427,1.271 2.583,1.469 0.156,0.198 10 false 3 5.083,1.01 7.156,1.24 2.073,0.229 10 false from Ignition Switch*2 5.104,0.542 7.156,0.771 2.052,0.229 10 false from IG1 NO.1 Relay*1 3.885,2.667 7.156,2.938 3.271,0.271 10 false Rear No. 1 Seat Inner Belt Assembly RH 3.885,2.5 4.344,2.698 0.458,0.198 10 false N43 4.052,2.052 4.208,2.25 0.156,0.198 10 false 1 5.917,2.063 6.073,2.26 0.156,0.198 10 false 2 4.271,2.281 4.885,2.479 0.615,0.198 10 false RBR+ 5.406,2.271 6.021,2.469 0.615,0.198 10 false RBR- 4.052,5.76 4.208,5.958 0.156,0.198 10 false 1 4.042,6.875 4.198,7.073 0.156,0.198 10 false 1 3.802,6.198 4.26,6.396 0.458,0.198 10 false N3 3.813,6.385 6.885,6.625 3.073,0.24 10 false Rear Door Courtesy Light Switch Assembly RH 3.833,7.333 4.292,7.531 0.458,0.198 10 false N4 3.833,7.531 6.906,7.771 3.073,0.24 10 false Rear Door Courtesy Light Switch Assembly LH

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the combination meter assembly, make sure to replace it with a new one.



PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Rear Left Side Door Rear left side door CLOSE or OPEN CLOSE: Rear left side door closed
OPEN: Rear left side door open
-
Rear Right Side Door Rear right side door CLOSE or OPEN CLOSE: Rear right side door closed
OPEN: Rear right side door open
-
Body Electrical > Combination Meter > Data List
Tester Display
Rear Left Side Door
Rear Right Side Door
50003 122 157,158
OK:

The GTS display changes correctly in response to the rear door condition.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS

NG

2.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
2nd-Row Seatbelt Buckle (R) Rear RH seat belt buckle switch signal ON or OFF ON: Rear RH seat belt not fastened
OFF: Rear RH seat belt fastened
-
2nd-Row Seatbelt Buckle (L) Rear LH seat belt buckle switch signal ON or OFF ON: Rear LH seat belt not fastened
OFF: Rear LH seat belt fastened
-
2nd-Row Seatbelt Buckle (C) Rear center seat belt buckle switch signal ON or OFF ON: Rear center seat belt not fastened
OFF: Rear center seat belt fastened
-
Body Electrical > Combination Meter > Data List
Tester Display
2nd-Row Seatbelt Buckle (R)
2nd-Row Seatbelt Buckle (L)
2nd-Row Seatbelt Buckle (C)
50003 122 74,75,76
OK:

The GTS display changes correctly in response to the rear door condition.



Result:
Result Proceed to
ON or OFF is displayed on the GTS screen according to the rear seat belt condition A
ON or OFF is not displayed normally on the GTS screen according to the rear LH seat belt condition B
ON or OFF is not displayed normally on the GTS screen according to the rear center seat belt condition B
ON or OFF is not displayed normally on the GTS screen according to the rear RH seat belt condition C



A

3.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - BATTERY)

B

6.INSPECT REAR CENTER SEAT LAP TYPE BELT ASSEMBLY LH

C

9.INSPECT REAR NO. 1 SEAT INNER BELT ASSEMBLY RH
3.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - BATTERY)
a.
E118483C03
1.531,0.292 1.969,0.583 0.438,0.292 2.719,1.292 2.896,0.646 2.896,0.646 3.063,0.646 true 1.615,0.365 2.073,0.563 0.458,0.198 10 false G27 0.063,0.063 0.375,0.26 0.313,0.198 10 false *a 3.125,0.573 3.427,0.771 0.302,0.198 10 false IG+
*a Front view of wire harness connector
(to Telltale Light Assembly)


Disconnect the telltale light assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G27-10 (IG+) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.INSPECT TELLTALE LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT TELLTALE LIGHT ASSEMBLY
a.

Remove the telltale light assembly.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING LIGHT(for Rear)>REMOVAL


b.

Inspect the telltale light assembly.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING LIGHT(for Rear)>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the G27 telltale light assembly connector.


b.

Disconnect the G9 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G27-1 (RLID) - G9-24 (RLMT) Always Below 1 Ω
G27-2 (RCID) - G9-23 (RCMT) Always Below 1 Ω
G27-3 (RRID) - G9-22 (RRMT) Always Below 1 Ω
G27-1 (RLID) or G9-24 (RLMT) - Body ground Always 10 kΩ or higher
G27-2 (RCID) or G9-23 (RCMT) - Body ground Always 10 kΩ or higher
G27-3 (RRID) or G9-22 (RRMT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT REAR CENTER SEAT LAP TYPE BELT ASSEMBLY LH
a.


Result:
Proceed to
OK
NG



OK

7.INSPECT REAR CENTER SEAT LAP TYPE BELT ASSEMBLY RH

NG

7.INSPECT REAR CENTER SEAT LAP TYPE BELT ASSEMBLY RH
a.


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (REAR CENTER SEAT LAP TYPE ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

NG

8.CHECK HARNESS AND CONNECTOR (REAR CENTER SEAT LAP TYPE ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the N44 rear center seat lap type belt assembly LH connector.


b.

Disconnect the G9 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N44-1 (LBR+) - G9-5 (RLBT) Always Below 1 Ω
N44-3 (CBR+) - G9-6 (RCSB) Always Below 1 Ω
N44-1 (LBR+) or G9-5 (RLBT) - Body ground Always 10 kΩ or higher
N44-3 (CBR+) or G9-6 (RCSB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT REAR NO. 1 SEAT INNER BELT ASSEMBLY RH


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (REAR NO. 1 SEAT INNER BELT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)

NG

10.CHECK HARNESS AND CONNECTOR (REAR NO. 1 SEAT INNER BELT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the N43 rear No. 1 seat inner belt assembly RH connector.


b.

Disconnect the G9 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N43-1 (RBR+) - G9-7 (RRBT) Always Below 1 Ω
N43-2 (RBR-) - Body ground Always Below 1 Ω
N43-1 (RBR+) or G9-7 (RRBT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR