Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _048729 1GR-FE ENGINE CONTROL _0231393 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P2237  Oxygen (A/F) Sensor Pumping Current Circuit / Open (for A/F sensor) (Bank 1 Sensor 1)  P2238  Oxygen Sensor Pumping Current Circuit Low (for A/F sensor) (Bank 1 Sensor 1)  P2239  Oxygen Sensor Pumping Current Circuit High (for A/F sensor) (Bank 1 Sensor 1)  P2240  Oxygen (A/F) Sensor Pumping Current Circuit / Open (for A/F sensor) (Bank 2 Sensor 1)  P2241  Oxygen Sensor Pumping Current Circuit Low (for A/F sensor) (Bank 2 Sensor 1)  P2242  Oxygen Sensor Pumping Current Circuit High (for A/F sensor) (Bank 2 Sensor 1)  P2252  Oxygen Sensor Reference Ground Circuit Low (for A/F sensor) (Bank 1 Sensor 1)  P2253  Oxygen Sensor Reference Ground Circuit High (for A/F sensor) (Bank 1 Sensor 1)  P2255  Oxygen Sensor Reference Ground Circuit Low (for A/F sensor) (Bank 2 Sensor 1)  P2256  Oxygen Sensor Reference Ground Circuit High (for A/F sensor) (Bank 2 Sensor 1)  


DESCRIPTION

HINT:

Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.


The air fuel ratio sensor generates voltage* that corresponds to the actual air fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air fuel ratio. The ECM determines the deviation from the stoichiometric air fuel ratio level, and regulates the fuel injection time. If the air fuel ratio sensor malfunctions, the ECM is unable to control the air fuel ratio accurately.

The air fuel ratio sensor is a planar type and integrated with a heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), current flows to the heater to heat the sensor, in order to facilitate accurate oxygen concentration detection. In addition, the sensor and heater portions are a narrow type. The heat generated by the heater is conducted to the solid electrolyte through alumina, therefore sensor activation is accelerated.

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a three-way catalytic converter is used. For the most efficient use of the three-way catalytic converter, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.

*: Value changes inside the ECM. Since the air fuel ratio sensor is a current output element, the current is converted into a voltage inside the ECM. Any measurements taken at the air fuel ratio sensor or ECM connectors will show a constant voltage.

A107164E55
1.646,2.385 1.938,2.385 false 1.479,2.427 0.667,2 true 2.938,2.354 3.417,2.75 true 2.729,2.177 3.417,2.333 true 2.875,1.771 3.417,1.667 true 3.094,1.656 3.417,1.333 true 2.875,2.083 3.417,2.333 true 1.115,2.948 1.24,3.146 0.125,0.198 10 false A 1.792,2.938 1.917,3.135 0.125,0.198 10 false A 0.104,1.917 0.667,2.135 0.563,0.219 10 false Element 0.083,2.75 1,2.969 0.917,0.219 10 false Exhaust Gas 2.573,2.969 3.604,3.188 1.031,0.219 10 false A-A Section 3.5,2.25 4.927,2.469 1.427,0.219 10 false Platinum electrode 2,2.302 2.448,2.5 0.448,0.198 10 false Cover 3.5,2.667 3.792,2.865 0.292,0.198 10 false Air 3.5,1.25 3.979,1.417 0.479,0.167 10 false Heater 3.5,1.583 4.667,2 1.167,0.417 10 false Solid electrolyte (Zirconia Element) 5.323,2.833 7.083,3.083 1.76,0.25 10 false Rich - Air Fuel Ratio - Lean 5.5,0.417 6.885,0.667 1.385,0.25 10 false Ideal Air-Fuel Mixture 4.396,0.583 5.417,0.844 1.021,0.26 10 false Output Voltage

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (for A/F sensor) (Bank 1 Sensor 1) An open or short in the circuit between terminals A1A+ and A1A- of the air fuel ratio sensor while the engine is running (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 1 sensor 1) circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

ECM


Comes on DTC stored
P2238 Oxygen Sensor Pumping Current Circuit Low (for A/F sensor) (Bank 1 Sensor 1)
·

Case 1:


Condition (a) or (b) is met for 5.0 seconds or more (2 trip detection logic):
(a) Voltage at terminal A1A+ is 0.5 V or less
(b) Voltage difference between terminals A1A+ and A1A- is 0.1 V or less
·

Case 2:


Air fuel ratio sensor admittance is less than 0.015 1/Ω (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 1 sensor 1) circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

ECM


Comes on DTC stored
P2239 Oxygen Sensor Pumping Current Circuit High (for A/F sensor) (Bank 1 Sensor 1) The A1A+ voltage is higher than 4.5 V (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 1 sensor 1) circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

ECM


Comes on DTC stored
P2240 Oxygen (A/F) Sensor Pumping Current Circuit / Open (for A/F sensor) (Bank 2 Sensor 1) An open or short in the circuit between terminals A2A+ and A2A- of the air fuel ratio sensor while the engine is running (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

ECM


Comes on DTC stored
P2241 Oxygen Sensor Pumping Current Circuit Low (for A/F sensor) (Bank 2 Sensor 1)
·

Case 1:


Condition (a) or (b) is met for 5.0 seconds or more (2 trip detection logic):
(a) Voltage at terminal A2A+ is 0.5 V or less
(b) Voltage difference between terminals A2A+ and A2A- is 0.1 V or less
·

Case 2:


Air fuel ratio sensor admittance is less than 0.015 1/Ω (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

ECM


Comes on DTC stored
P2242 Oxygen Sensor Pumping Current Circuit High (for A/F sensor) (Bank 2 Sensor 1) The A2A+ voltage is higher than 4.5 V (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

ECM


Comes on DTC stored
P2252 Oxygen Sensor Reference Ground Circuit Low (for A/F sensor) (Bank 1 Sensor 1) The A1A- voltage is 0.5 V or less (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 1 sensor 1) circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

ECM


Comes on DTC stored
P2253 Oxygen Sensor Reference Ground Circuit High (for A/F sensor) (Bank 1 Sensor 1) The A1A- voltage is higher than 4.5 V (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 1 sensor 1) circuit

·

Air fuel ratio sensor (bank 1 sensor 1)

·

ECM


Comes on DTC stored
P2255 Oxygen Sensor Reference Ground Circuit Low (for A/F sensor) (Bank 2 Sensor 1) The A2A- voltage is 0.5 V or less (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

ECM


Comes on DTC stored
P2256 Oxygen Sensor Reference Ground Circuit High (for A/F sensor) (Bank 2 Sensor 1) The A2A- voltage is higher than 4.5 V (2 trip detection logic).
·

Open or short in air fuel ratio sensor (bank 2 sensor 1) circuit

·

Air fuel ratio sensor (bank 2 sensor 1)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

These DTCs are output when there is an open or short in the air fuel ratio sensor circuit, or if the air fuel ratio sensor output drops. To detect these problems, the voltage of the air fuel ratio sensor is monitored when turning the ignition switch to ON, and the admittance (admittance is an electrical term that indicates the ease of flow of current) is checked while driving. If the voltage of the air fuel ratio sensor is between 0.5 V and 4.5 V, it is considered normal. If the voltage is out of the specified range, or the admittance is less than the standard value, the ECM determines that there is a malfunction in the air fuel ratio sensor. If the same malfunction is detected in the next driving cycle, the ECM will illuminate the MIL and store a DTC.

MONITOR STRATEGY

Required Sensors/Components Air fuel ratio sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine and wait 5 minutes.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255 or P2256.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, idle the engine for 5 minutes and check the DTC judgment result again.




WIRING DIAGRAM

A372130E03
0.583,7 1.083,7.25 0.5,0.25 10 false Battery 0.417,5.667 1.417,5.833 1,0.167 10 false FL MAIN 3.0W 0.823,1.083 1.24,1.25 0.417,0.167 10 false J/B-B 0.729,0.667 1.313,0.833 0.583,0.167 10 false A/F HTR 1.781,0.906 2.031,1.073 0.25,0.167 10 false 2B 1.833,0.708 2,0.875 0.167,0.167 10 false 1 1.833,1.104 2,1.271 0.167,0.167 10 false 9 1.792,1.313 2.042,1.479 0.25,0.167 10 false 2P 2.26,1.052 2.927,1.385 0.667,0.333 10 false EFI-MAIN NO.1 2.833,1.583 3.833,1.75 1,0.167 10 false EFI-MAIN NO.1 2,1.917 4.667,2.167 2.667,0.25 10 false Instrument Panel Junction Block Assembly 3.75,1.083 4.417,1.25 0.667,0.167 10 false EFI NO.1 4.708,0.719 4.875,0.885 0.167,0.167 10 false 3 4.667,0.917 4.917,1.083 0.25,0.167 10 false 2K 4.677,1.323 4.927,1.49 0.25,0.167 10 false 2J 4.708,1.115 4.875,1.281 0.167,0.167 10 false 5 5.229,1.167 5.813,1.333 0.583,0.167 10 false A/F HTR 5.083,0.833 5.25,1 0.167,0.167 10 false 1 5.083,0.417 5.25,0.583 0.167,0.167 10 false 5 5.833,0.417 6,0.583 0.167,0.167 10 false 3 5.833,0.833 6,1 0.167,0.167 10 false 2 2.167,2.917 2.417,3.083 0.25,0.167 10 false +B 1.917,2.917 2.083,3.083 0.167,0.167 10 false 2 2.698,2.917 3.115,3.083 0.417,0.167 10 false HA1A 3.167,2.917 3.333,3.083 0.167,0.167 10 false 1 2.719,3.417 3.135,3.583 0.417,0.167 10 false A1A+ 2.75,3.833 3.167,4 0.417,0.167 10 false A1A- 3.167,3.417 3.333,3.583 0.167,0.167 10 false 3 3.167,3.833 3.333,4 0.167,0.167 10 false 4 2.719,5.083 3.135,5.25 0.417,0.167 10 false HA2A 2.75,5.563 3.167,5.729 0.417,0.167 10 false A2A+ 2.75,6 3.167,6.167 0.417,0.167 10 false A2A- 4,3.333 4.167,3.5 0.167,0.167 10 false * 1.833,4.25 2.25,4.417 0.417,0.167 10 false C66 1.833,4.417 4.333,4.667 2.5,0.25 10 false Air Fuel Ratio Sensor (Bank 1 Sensor 1) 1.802,6.333 2.135,6.51 0.333,0.177 10 false C79 1.802,6.5 4.302,6.75 2.5,0.25 10 false Air Fuel Ratio Sensor (Bank 2 Sensor 1) 2.833,7.25 3.583,7.417 0.75,0.167 10 false *: Shielded 6.167,7.333 6.583,7.5 0.417,0.167 10 false ECM 5.396,2.833 5.646,3 0.25,0.167 10 false 17 5.313,3.042 5.729,3.208 0.417,0.167 10 false C82 5.75,2.917 6.167,3.083 0.417,0.167 10 false HA1A 5.302,3.51 5.719,3.677 0.417,0.167 10 false C84 5.417,3.302 5.583,3.469 0.167,0.167 10 false 7 5.75,3.406 6.167,3.573 0.417,0.167 10 false A1A+ 5.417,3.771 5.583,3.938 0.167,0.167 10 false 8 5.302,3.979 5.719,4.146 0.417,0.167 10 false C84 5.75,3.885 6.167,4.052 0.417,0.167 10 false A1A- 5.365,4.969 5.615,5.135 0.25,0.167 10 false 12 5.302,5.177 5.719,5.344 0.417,0.167 10 false C82 5.75,5.083 6.167,5.25 0.417,0.167 10 false HA2A 5.75,5.5 6.167,5.667 0.417,0.167 10 false A2A+ 5.417,5.427 5.583,5.594 0.167,0.167 10 false 1 5.302,5.656 5.719,5.823 0.417,0.167 10 false C84 5.417,5.917 5.583,6.083 0.167,0.167 10 false 2 5.75,6.042 6.167,6.208 0.417,0.167 10 false A2A- 5.302,6.135 5.719,6.302 0.417,0.167 10 false C84 5.375,6.792 5.625,6.958 0.25,0.167 10 false 36 5.75,7 6.167,7.167 0.417,0.167 10 false MREL 5.302,7 5.719,7.167 0.417,0.167 10 false G145 0.792,0.333 0.958,0.5 0.167,0.167 10 false 1 1.104,0.333 1.271,0.5 0.167,0.167 10 false 2 1.917,5.083 2.083,5.25 0.167,0.167 10 false 2 2.167,5.083 2.417,5.25 0.25,0.167 10 false +B 3.167,5.083 3.333,5.25 0.167,0.167 10 false 1 3.167,5.563 3.333,5.729 0.167,0.167 10 false 3 3.167,6 3.333,6.167 0.167,0.167 10 false 4 4.167,5.583 4.333,5.75 0.167,0.167 10 false *

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Refer to "Data List / Active Test" [AFS Voltage B1S1 and AFS Voltage B2S1].

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C66-1 (HA1A) - C82-17 (HA1A) Always Below 1 Ω
C66-3 (A1A+) - C84-7 (A1A+) Always Below 1 Ω
C66-4 (A1A-) - C84-8 (A1A-) Always Below 1 Ω
C79-1 (HA2A) - C82-12 (HA2A) Always Below 1 Ω
C79-3 (A2A+) - C84-1 (A2A+) Always Below 1 Ω
C79-4 (A2A-) - C84-2 (A2A-) Always Below 1 Ω
C66-1 (HA1A) or C82-17 (HA1A) - Body ground and other terminals Always 10 kΩ or higher
C66-3 (A1A+) or C84-7 (A1A+) - Body ground and other terminals Always 10 kΩ or higher
C66-4 (A1A-) or C84-8 (A1A-) - Body ground and other terminals Always 10 kΩ or higher
C79-1 (HA2A) or C82-12 (HA2A) - Body ground and other terminals Always 10 kΩ or higher
C79-3 (A2A+) or C84-1 (A2A+) - Body ground and other terminals Always 10 kΩ or higher
C79-4 (A2A-) or C84-2 (A2A-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.REPLACE AIR FUEL RATIO SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

3.CHECK WHETHER DTC OUTPUT RECURS
3.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the GTS on.


g.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


h.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 234 20

i.

Input the DTC: P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255 or P2256.


j.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255 or P2256 is output)
B




A

END

B