Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _048729 1GR-FE ENGINE CONTROL _0231393 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0617  Starter Relay Circuit High  


MONITOR DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.

If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores this DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.43 mph) or more for 20 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High All of the following conditions are met, and a (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic).

(a) The vehicle speed is 20 km/h (12.43 mph) or more.

(b) The engine speed is 1000 rpm or higher.

(c) The STA signal is on.


·

Park/neutral position switch assembly

·

ST NO. 1 relay circuit

·

ECM


Comes on DTC stored

MONITOR STRATEGY

Required Sensors/Components (Main) ST NO. 1 relay
Park/neutral position switch assembly
Certification ECU (smart key ECU assembly)
Required Sensors/Components (Related) Vehicle speed sensor
Crankshaft position sensor
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Vehicle speed 20 km/h (12.43 mph) or more
Engine speed 1000 rpm or higher

TYPICAL MALFUNCTION THRESHOLDS

Starter signal On

CONFIRMATION DRIVING PATTERN

A231469E24
1.229,1.979 1.656,2.198 0.427,0.219 10 Idling 0.396,2.26 1.604,2.583 1.208,0.323 10 Ignition Switch ON 1.063,0.865 1.635,1.073 0.573,0.208 10 24 km/h 2.396,2.854 3.083,3.167 0.688,0.313 10 5 seconds or more 3.594,2.938 4.865,3.104 1.271,0.167 10 20 seconds or more 2.01,2.333 2.302,2.552 0.292,0.219 10 [A] 2.615,2.125 2.823,2.302 0.208,0.177 10 [B] 4.063,0.458 4.292,0.625 0.229,0.167 10 [C] 4.885,3.333 5.115,3.5 0.229,0.167 10 [D]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine.

7.

Idle the engine for 5 seconds or more [B].

8.

Drive the vehicle at 24 km/h (15 mph) or more for 20 seconds or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0617.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] and [D] again and, if necessary, extend the driving time.




WIRING DIAGRAM

A372126E04
0.083,0.083 2.542,0.313 2.458,0.229 12 false w/ Smart Entry and Start System: 1.417,1 1.667,1.167 0.25,0.167 10 false NE 1.25,1.583 1.667,1.75 0.417,0.167 10 false STAR 1.333,2.083 1.667,2.25 0.333,0.167 10 false STA 1.76,2.104 2.094,2.271 0.333,0.167 10 false G17 1.813,1.917 2.063,2.083 0.25,0.167 10 false 37 1.76,1.594 2.094,1.76 0.333,0.167 10 false G17 1.813,1.396 2.063,1.563 0.25,0.167 10 false 16 1.771,1.052 2.104,1.219 0.333,0.167 10 false G16 1.865,0.833 2.031,1 0.167,0.167 10 false 6 4.083,2.167 4.25,2.333 0.167,0.167 10 false 4 4.083,3 4.25,3.167 0.167,0.167 10 false 5 4.417,2.333 4.75,2.5 0.333,0.167 10 false C22 4.417,2.5 5.417,3.083 1,0.583 10 false Park/Neutral Position Switch Assembly 5.333,0.833 5.583,1 0.25,0.167 10 false 13 5.26,1.052 5.677,1.219 0.417,0.167 10 false G145 5.75,1.052 6.083,1.219 0.333,0.167 10 false NEO 5.333,1.375 5.583,1.542 0.25,0.167 10 false 23 5.271,1.594 5.688,1.76 0.417,0.167 10 false C85 5.75,1.583 6.167,1.75 0.417,0.167 10 false NSW 5.333,3.552 5.583,3.719 0.25,0.167 10 false 28 5.271,3.771 5.688,3.938 0.417,0.167 10 false G145 5.75,3.667 6.167,3.833 0.417,0.167 10 false STA 6.083,5 6.5,5.167 0.417,0.167 10 false ECM 3.083,4.083 3.25,4.25 0.167,0.167 10 false 2 2.5,4.083 2.667,4.25 0.167,0.167 10 false 5 2.5,5.083 2.667,5.25 0.167,0.167 10 false 3 3.083,5.083 3.25,5.25 0.167,0.167 10 false 1 3.333,4.583 3.917,4.75 0.583,0.167 10 false ST NO.1 0.583,3.781 1.25,3.948 0.667,0.167 10 false ST NO. 1 0.583,5.271 1.583,5.438 1,0.167 10 false FL MAIN 3.0W 0.75,6.833 1.25,7.083 0.5,0.25 10 false Battery 1.052,5.917 1.302,6.083 0.25,0.167 10 false D3 1.729,5.688 2.063,5.854 0.333,0.167 10 false C26 1.417,6.75 2.083,7.167 0.667,0.417 10 false Starter Assembly 0.25,2.635 2.083,3.083 1.833,0.448 10 false Certification ECU (Smart Key ECU Assembly) 2.083,5.667 2.25,5.833 0.167,0.167 10 false 1 1.104,5.688 1.271,5.854 0.167,0.167 10 false 1

A372127E03
0.083,0.083 2.604,0.333 2.521,0.25 12 false w/o Smart Entry and Start System: 1.417,1 1.583,1.167 0.167,0.167 10 false 4 2.583,1 2.75,1.167 0.167,0.167 10 false 2 1.615,0.99 1.948,1.156 0.333,0.167 10 false AM2 2.177,1 2.5,1.167 0.323,0.167 10 false ST2 1.583,1.5 2,1.667 0.417,0.167 10 false G135 1.583,1.667 2.583,1.917 1,0.25 10 false Ignition Switch 0.5,2.271 2,2.438 1.5,0.167 10 false STRG LOCK/AM2 NO.1 0.5,4.771 1.5,4.938 1,0.167 10 false FL MAIN 3.0W 0.667,6.75 1.167,7 0.5,0.25 10 false Battery 1.417,3.917 2,4.083 0.583,0.167 10 false ST NO.1 3.583,2 3.75,2.167 0.167,0.167 10 false 5 3.781,2 3.948,2.167 0.167,0.167 10 false L 4.281,2 4.448,2.167 0.167,0.167 10 false B 4.5,2 4.667,2.167 0.167,0.167 10 false 4 3.5,2.417 3.833,2.583 0.333,0.167 10 false C22 3.5,2.583 4.917,3 1.417,0.417 10 false Park/Neutral Position Switch Assembly 2.667,4 2.833,4.167 0.167,0.167 10 false 5 3.25,4 3.417,4.167 0.167,0.167 10 false 2 3.5,4.5 4.083,4.667 0.583,0.167 10 false ST NO.1 3.25,5 3.417,5.167 0.167,0.167 10 false 1 2.667,5 2.833,5.167 0.167,0.167 10 false 3 1.969,5.427 2.302,5.594 0.333,0.167 10 false C26 1.292,5.833 1.542,6 0.25,0.167 10 false D3 1.25,6.667 2.417,6.917 1.167,0.25 10 false Starter Assembly 5.417,0.917 5.667,1.083 0.25,0.167 10 false 23 5.344,1.135 5.76,1.302 0.417,0.167 10 false C85 5.833,1.115 6.25,1.281 0.417,0.167 10 false NSW 5.417,3.479 5.667,3.646 0.25,0.167 10 false 28 5.333,3.688 5.75,3.854 0.417,0.167 10 false G145 5.833,3.583 6.167,3.75 0.333,0.167 10 false STA 6.167,4.917 6.583,5.083 0.417,0.167 10 false ECM 2.333,5.417 2.5,5.583 0.167,0.167 10 false 1 1.333,5.646 1.5,5.813 0.167,0.167 10 false 1

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

Powertrain > Engine > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the value displayed on the GTS when the vehicle is driven at 20 km/h (12.43 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


Result:
Condition Starter Signal Result
Driving at 20 km/h (12.4 mph) or more OFF A
ON B




A

B

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

OK

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

NG

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace harness or connector (STA signal circuit).


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0617 is output A
DTCs are not output B




A

B

END