Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _048729 1GR-FE ENGINE CONTROL _0231393 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0137  Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2)  P0157  Oxygen Sensor Circuit Low Voltage (Bank 2 Sensor 2)  


DESCRIPTION

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC (Three-Way Catalytic Converter) is used. For the most efficient use of the TWC, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric air fuel level. For the purpose of helping the ECM to deliver accurate air fuel ratio control, a heated oxygen sensor is used.

The heated oxygen sensor is located behind the TWC, and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with the heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).

When the air fuel ratio becomes lean, the oxygen concentration in the exhaust gas is high. The heated oxygen sensor informs the ECM that the post-TWC air fuel ratio is lean (low voltage, i.e. less than 0.45 V).

Conversely, when the air fuel ratio is richer than the stoichiometric air fuel level, the oxygen concentration in the exhaust gas is low. The heated oxygen sensor informs the ECM that the post-TWC air fuel ratio is rich (high voltage, i.e. higher than 0.45 V). The heated oxygen sensor has the property of changing its output voltage drastically when the air fuel ratio is close to the stoichiometric level.

The ECM uses the supplementary information from the heated oxygen sensor to determine whether the air fuel ratio after the TWC is rich or lean, and adjusts the fuel injection duration accordingly. Thus, if the heated oxygen sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in the primary air fuel ratio control.

A348210E01
0.948,2.896 0.667,3.25 true 3.333,1.75 2.781,1.635 true 3.5,1.333 3.167,1.5 true 3.25,2.5 2.708,2.052 true 3.25,2.5 2.729,2.167 true 2.698,2.552 3,2.917 true 2.635,2.25 2.083,2.083 true 0.5,3.25 0.917,3.417 0.417,0.167 10 false Cover 4.333,0.75 5.333,1 1,0.25 10 false Output Voltage 5.083,0.333 6.417,0.583 1.333,0.25 10 false Ideal Air-fuel Mixture 4.802,2.833 6.708,3.083 1.906,0.25 10 false Richer - Air-fuel Ratio - Leaner 3.583,1.25 4.167,1.5 0.583,0.25 10 false Housing 3.396,1.667 4.417,1.917 1.021,0.25 10 false Solid Electrolyte 3.344,2 4.5,2.24 1.156,0.24 10 false (Zirconia Element) 3.333,2.417 4.583,2.656 1.25,0.24 10 false Platinum Electrode 3.063,2.917 4.25,3.167 1.188,0.25 10 false Coating (Ceramic) 1.583,2 2.083,2.198 0.5,0.198 10 false Heater 1.875,2.885 2.75,3.083 0.875,0.198 10 false Exhaust Gas 1.5,0.75 2.583,0.948 1.083,0.198 10 false Atmospheric Air

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0137 Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2) Low voltage (open):
During active air fuel ratio control, the following conditions (a) and (b) are met for a certain period of time (2 trip detection logic)

(a) Heated oxygen sensor voltage output is less than 0.21 V.

(b) Target air fuel ratio rich.


·

Heated oxygen sensor (bank 1 sensor 2) circuit

·

Heated oxygen sensor (bank 1 sensor 2)

·

Air fuel ratio sensor (bank 1 sensor 1)

·

Gas leak from exhaust system


Comes on DTC stored
P0157 Oxygen Sensor Circuit Low Voltage (Bank 2 Sensor 2) Low voltage (open):
During active air fuel ratio control, the following conditions (a) and (b) are met for a certain period of time (2 trip detection logic)

(a) Heated oxygen sensor voltage output is less than 0.21 V.

(b) Target air fuel ratio rich.


·

Heated oxygen sensor (bank 2 sensor 2) circuit

·

Heated oxygen sensor (bank 2 sensor 2)

·

Air fuel ratio sensor (bank 2 sensor 1)

·

Gas leak from exhaust system


Comes on DTC stored

MONITOR DESCRIPTION

Active Air Fuel Ratio Control


The ECM usually performs air fuel ratio feedback control so that the air fuel ratio sensor output indicates a near stoichiometric air fuel level. This vehicle includes active air fuel ratio control in addition to regular air fuel ratio control. The ECM performs active air fuel ratio control to detect any deterioration in the Three-Way Catalytic Converter (TWC) and heated oxygen sensor malfunctions (refer to the diagram below).

Active air fuel ratio control is performed for approximately 30 seconds while driving with a warm engine. During active air fuel ratio control, the air fuel ratio is forcibly regulated to become lean or rich by the ECM. If the ECM detects a malfunction, a DTC is stored.


Open or Short in Heated Oxygen Sensor Circuit (DTC P0137 and P0157)


During active air fuel ratio control, the ECM calculates the Oxygen Storage Capacity (OSC)* of the Three-Way Catalytic Converter (TWC) by forcibly regulating the air fuel ratio to become rich or lean.

If the heated oxygen sensor has an open circuit, or the voltage output of the sensor noticeably decreases, the OSC indicates an extraordinarily high value. Even if the ECM attempts to continue regulating the air fuel ratio to become rich or lean, the heated oxygen sensor output does not change.

While performing active air fuel ratio control, when the target air fuel ratio is rich and the heated oxygen sensor voltage output is less than 0.21 V (lean), the ECM interprets this as an abnormally low sensor output voltage and stores DTC P0137 or P0157.

HINT:

*: The TWC has the capability to store oxygen. The OSC and the emission purification capacity of the TWC are mutually related.


A354230E02
4.521,1.573 4.417,1.5 4.417,1.5 4.167,1.5 true 5.563,1.917 5.667,1.458 5.667,1.458 5.917,1.458 true 5.833,2.24 6.167,1.917 6.167,1.917 6.417,1.917 true 5.667,3 5.917,3.25 5.917,3.25 6.167,3.25 true 0.094,0.083 4.25,0.333 4.156,0.25 10 false Heated Oxygen Sensor Circuit Low Voltage (P0137 or P0157: Open) 4.302,0.135 6,0.333 1.698,0.198 10 false Approximately 30 seconds 0.365,1.156 4.802,1.354 4.438,0.198 10 false Active Air-Fuel Ratio Control 0.354,1.667 3.563,1.865 3.208,0.198 10 false Target Air-Fuel Ratio 0.323,2.563 4.604,2.76 4.281,0.198 10 false Heated Oxygen Sensor Voltage 3.115,1.271 3.573,1.469 0.458,0.198 10 false Off 2.438,1.552 3.323,2.042 0.885,0.49 10 false Stoichiometric Air-Fuel Level 2.813,2.74 3.333,2.917 0.521,0.177 10 false 0.21 V 3.667,1.417 4.25,1.583 0.583,0.167 10 false Normal 4.667,1.948 5.281,2.146 0.615,0.198 10 false Rich 4.75,1.219 5.375,1.417 0.625,0.198 10 false Operating 6,1.385 6.656,1.583 0.656,0.198 10 false Abnormal 6.5,1.833 7.01,2.031 0.51,0.198 10 false Normal 6.25,3.167 6.906,3.365 0.656,0.198 10 false Abnormal


MONITOR STRATEGY

Required Sensors/Components (Main) Heated oxygen sensor (sensor 2)
Required Sensors/Components (Related) Crankshaft position sensor
Engine coolant temperature sensor
Mass air flow meter sub-assembly
Throttle position sensor
Air fuel ratio sensor
Frequency of Operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

Heated Oxygen Sensor Voltage Check (Low Voltage)
Active air fuel ratio control Executing
Active air fuel ratio control begins when all of the following conditions met: -
Battery voltage 11 V or higher
Engine coolant temperature 75°C (167°F) or higher
Idling Off
Engine speed Less than 3200 rpm
Air fuel ratio sensor status Activated
Fuel system status Closed loop
Engine load 10% or higher, and less than 80%

TYPICAL MALFUNCTION THRESHOLDS

P0137, P0157: Heated Oxygen Sensor Voltage Check (Low Voltage)
Both of the following conditions are met -
(a) Commanded air fuel ratio 14.3 or less
(b) Heated oxygen sensor voltage Less than 0.21 V

CONFIRMATION DRIVING PATTERN

HINT:
·

This confirmation driving pattern is used in the "Perform Confirmation Driving Pattern" procedure of the following diagnostic troubleshooting procedure.

·

Performing this confirmation driving pattern will activate the heated oxygen sensor monitor (the catalyst monitor is performed simultaneously). This is very useful for verifying the completion of a repair.



A264212E37
1.74,2.427 1.563,2.802 1.563,2.802 1.417,2.802 false 4.021,0.719 4.25,0.958 0.229,0.24 10 false [C] 3.49,2.906 4.792,3.083 1.302,0.177 10 false 10 minutes or more 1.094,1.354 1.698,1.51 0.604,0.156 10 false 60 km/h 2.021,2.427 2.25,2.625 0.229,0.198 10 false [A] 1.021,0.479 1.677,0.688 0.656,0.208 10 false 100 km/h 1.25,2.229 1.635,2.448 0.385,0.219 10 false Idling 2.677,2.135 2.906,2.344 0.229,0.208 10 false [B] 2.333,2.917 3.156,3.115 0.823,0.198 10 false Warming up 5.01,3.313 5.271,3.573 0.26,0.26 10 false [D] 0.219,2.719 1.458,2.938 1.24,0.219 10 false Ignition Switch ON

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

7.

With the shift lever in D, drive the vehicle at 60 to 100 km/h (37 to 62 mph) for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0137 or P0157.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] and [D] again.




WIRING DIAGRAM

A372117E02
0.917,5.5 1.417,5.75 0.5,0.25 10 false Battery 0.75,4.188 1.75,4.354 1,0.167 10 false FL MAIN 3.0W 0.75,3.115 1.167,3.281 0.417,0.167 10 false J/B-B 0.333,1.635 0.5,1.802 0.167,0.167 10 false 1 0.531,1.635 0.781,1.802 0.25,0.167 10 false 2B 0.823,1.635 0.99,1.802 0.167,0.167 10 false 5 1.021,1.646 1.271,1.813 0.25,0.167 10 false 2J 0.719,0.927 1.385,1.26 0.667,0.333 10 false EFI-MAIN NO.1 1.417,1.917 2.583,2.5 1.167,0.583 10 false Instrument Panel Junction Block Assembly 2.073,0.927 2.74,1.094 0.667,0.167 10 false EFI NO.1 2.74,0.792 2.99,0.958 0.25,0.167 10 false 2N 2.771,0.583 2.938,0.75 0.167,0.167 10 false 1 2.698,1.635 2.948,1.802 0.25,0.167 10 false 2P 2.479,1.635 2.646,1.802 0.167,0.167 10 false 9 3.667,0.667 3.833,0.833 0.167,0.167 10 false 2 3.865,0.667 4.281,0.833 0.417,0.167 10 false +B 4.417,0.667 4.833,0.833 0.417,0.167 10 false HT1B 4.917,0.667 5.083,0.833 0.167,0.167 10 false 1 4.417,1.156 4.833,1.323 0.417,0.167 10 false OX1B 4.917,1.146 5.083,1.313 0.167,0.167 10 false 3 5.135,1 5.302,1.167 0.167,0.167 10 false * 4.583,1.583 4.833,1.75 0.25,0.167 10 false E2 4.917,1.583 5.083,1.75 0.167,0.167 10 false 4 5.5,0.583 5.75,0.75 0.25,0.167 10 false 18 5.427,0.792 5.844,0.958 0.417,0.167 10 false C82 5.542,1.042 5.708,1.208 0.167,0.167 10 false 9 5.427,1.25 5.844,1.417 0.417,0.167 10 false C84 5.49,1.458 5.74,1.625 0.25,0.167 10 false 10 5.417,1.667 5.833,1.833 0.417,0.167 10 false C84 5.865,0.698 6.281,0.865 0.417,0.167 10 false HT1B 5.865,1.146 6.281,1.313 0.417,0.167 10 false OX1B 5.865,1.563 6.281,1.729 0.417,0.167 10 false EX1B 5.854,3.333 6.271,3.5 0.417,0.167 10 false HT2B 3.667,2 4.083,2.167 0.417,0.167 10 false C98 3.667,2.167 5.167,2.583 1.5,0.417 10 false Heated Oxygen Sensor (Bank 1 Sensor 2) 3.667,3.333 3.833,3.5 0.167,0.167 10 false 2 3.865,3.333 4.115,3.5 0.25,0.167 10 false +B 4.417,3.333 4.833,3.5 0.417,0.167 10 false HT2B 4.917,3.333 5.083,3.5 0.167,0.167 10 false 1 4.417,3.75 4.833,3.917 0.417,0.167 10 false OX2B 4.917,3.75 5.083,3.917 0.167,0.167 10 false 3 5.083,3.625 5.25,3.792 0.167,0.167 10 false * 4.583,4.167 4.833,4.333 0.25,0.167 10 false E2 4.917,4.167 5.083,4.333 0.167,0.167 10 false 4 3.667,4.583 4.083,4.75 0.417,0.167 10 false C97 3.667,4.75 5.167,5.167 1.5,0.417 10 false Heated Oxygen Sensor (Bank 2 Sensor 2) 2.75,5.917 3.5,6.083 0.75,0.167 10 false *: Shielded 6.167,6.333 6.5,6.5 0.333,0.167 10 false ECM 5.427,5.5 5.844,5.667 0.417,0.167 10 false G145 5.531,4.104 5.698,4.271 0.167,0.167 10 false 4 5.427,4.313 5.844,4.479 0.417,0.167 10 false C84 5.427,3.885 5.844,4.052 0.417,0.167 10 false C84 5.531,3.667 5.698,3.833 0.167,0.167 10 false 3 5.427,3.438 5.844,3.604 0.417,0.167 10 false C82 5.5,3.219 5.75,3.385 0.25,0.167 10 false 13 5.854,3.781 6.271,3.948 0.417,0.167 10 false OX2B 5.854,4.198 6.271,4.365 0.417,0.167 10 false EX2B 5.865,5.5 6.281,5.667 0.417,0.167 10 false MREL 1.333,1.521 2.333,1.688 1,0.167 10 false EFI-MAIN NO.1 5.5,5.292 5.75,5.458 0.25,0.167 10 false 36

CAUTION / NOTICE / HINT

HINT:

Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the GTS.

1.

Connect the GTS to the DLC3.

2.

Start the engine.

3.

Turn the GTS on.

4.

Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.

5.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / Data List / All Data / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.

6.

Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

7.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the GTS.



HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.



GTS Display
(Sensor)
Injection Volume Status Voltage
AFS Voltage B1S1
AFS Voltage B2S1
(Air fuel ratio)
12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2S B1S2
O2S B2S2
(Heated oxygen)
12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V

NOTICE:

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


A283583E20
5.792,3.625 7.115,3.896 1.323,0.271 10 false - Air fuel ratio sensor 3.823,4.927 4.531,5.104 0.708,0.177 8 false Below 0.4 V 3.208,4.396 4.333,4.615 1.125,0.219 10 false Output Voltage 3.25,3.365 4.542,3.615 1.292,0.25 10 false Injection Volume 3.229,1.292 4.521,1.542 1.292,0.25 10 false Injection Volume 3.24,2.313 4.333,2.521 1.094,0.208 10 false Output Voltage 0.625,1.292 1.917,1.542 1.292,0.25 10 false Injection Volume 0.625,3.365 1.917,3.615 1.292,0.25 10 false Injection Volume 0.594,5.438 1.885,5.688 1.292,0.25 10 false Injection Volume 0.604,7.49 1.896,7.74 1.292,0.25 10 false Injection Volume 3.25,7.49 4.542,7.74 1.292,0.25 10 false Injection Volume 3.25,5.438 4.542,5.688 1.292,0.25 10 false Injection Volume 0.635,2.302 1.823,2.51 1.188,0.208 10 false Output Voltage 0.625,4.396 1.792,4.646 1.167,0.25 10 false Output Voltage 0.552,6.479 1.719,6.729 1.167,0.25 10 false Output Voltage 0.573,8.563 1.74,8.813 1.167,0.25 10 false Output Voltage 3.24,8.563 4.406,8.813 1.167,0.25 10 false Output Voltage 3.25,6.479 4.417,6.729 1.167,0.25 10 false Output Voltage 3.51,4.698 4.542,4.885 1.031,0.188 8 false Higher than 0.55 V 0.927,2.646 1.958,2.833 1.031,0.188 8 false Higher than 3.4 V 1.177,2.885 1.927,3.073 0.75,0.188 8 false Below 3.1 V 1.531,1.594 1.979,1.781 0.448,0.188 8 false 12.5% 1.479,1.833 1.927,2.021 0.448,0.188 8 false -12.5% 3.5,2.604 4.531,2.792 1.031,0.188 8 false Higher than 0.55 V 3.813,2.844 4.521,3.021 0.708,0.177 8 false Below 0.4 V 4.156,1.594 4.604,1.781 0.448,0.188 8 false 12.5% 4.115,1.833 4.563,2.021 0.448,0.188 8 false -12.5% 4.146,3.729 4.594,3.917 0.448,0.188 8 false 12.5% 4.104,3.917 4.552,4.104 0.448,0.188 8 false -12.5% 4.104,5.958 4.552,6.146 0.448,0.188 8 false -12.5% 4.104,8.021 4.552,8.208 0.448,0.188 8 false -12.5% 4.156,5.74 4.604,5.927 0.448,0.188 8 false 12.5% 4.156,7.813 4.604,8 0.448,0.188 8 false 12.5% 1.49,7.813 1.938,8 0.448,0.188 8 false 12.5% 1.49,5.75 1.938,5.938 0.448,0.188 8 false 12.5% 1.5,3.677 1.948,3.865 0.448,0.188 8 false 12.5% 1.448,3.896 1.896,4.083 0.448,0.188 8 false -12.5% 1.448,5.948 1.896,6.135 0.448,0.188 8 false -12.5% 1.438,8.021 1.885,8.208 0.448,0.188 8 false -12.5% 0.844,4.802 2.042,5.052 1.198,0.25 8 false Almost no reaction 0.854,8.938 2.052,9.188 1.198,0.25 8 false Almost no reaction 3.5,8.938 4.698,9.188 1.198,0.25 8 false Almost no reaction 3.49,6.865 4.688,7.115 1.198,0.25 8 false Almost no reaction 0.917,6.771 1.948,6.958 1.031,0.188 8 false Higher than 3.4 V 1.167,7.021 1.917,7.208 0.75,0.188 8 false Below 3.1 V 0.24,2.083 0.396,2.281 0.156,0.198 10 false 1 0.24,4.25 0.396,4.448 0.156,0.198 10 false 2 0.25,6.333 0.406,6.531 0.156,0.198 10 false 3 0.24,8.417 0.396,8.615 0.156,0.198 10 false 4 0.125,0.688 0.573,0.938 0.448,0.25 10 false Case 0.792,0.583 2.802,0.969 2.01,0.385 10 false Air Fuel Ratio Sensor (Sensor 1) Output Voltage 3.5,0.583 5.594,1.031 2.094,0.448 10 false Heated Oxygen Sensor (Sensor 2) Output Voltage 5.969,0.583 7.01,1 1.042,0.417 10 false Main Suspected Trouble Area 6.396,2.115 6.552,2.313 0.156,0.198 10 false - 5.802,4.031 7.125,4.469 1.323,0.438 10 false - Air fuel ratio sensor heater 5.802,4.635 7.125,5.073 1.323,0.438 10 false - Air fuel ratio sensor circuit 5.917,5.604 6.969,5.979 1.052,0.375 10 false - Heated oxygen sensor 5.927,6.198 6.969,6.625 1.042,0.427 10 false - Heated oxygen sensor heater 5.927,6.792 6.969,7.229 1.042,0.438 10 false - Heated oxygen sensor circuit 5.927,7.469 6.813,7.875 0.885,0.406 10 false - Fuel injector assembly 5.917,8.083 7.073,8.417 1.156,0.333 10 false - Fuel pressure 5.917,8.531 7.01,9.313 1.094,0.781 10 false - Gas leak from exhaust system 2.552,2.75 3,2.938 0.448,0.188 8 false OK 2.5,4.719 2.948,4.906 0.448,0.188 8 false NG 2.552,6.865 3,7.052 0.448,0.188 8 false OK 2.5,8.844 2.948,9.031 0.448,0.188 8 false NG 5.167,2.708 5.615,2.896 0.448,0.188 8 false OK 5.167,4.813 5.615,5 0.448,0.188 8 false OK 5.135,8.854 5.583,9.042 0.448,0.188 8 false NG 5.135,6.771 5.583,6.958 0.448,0.188 8 false NG

·

Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the air fuel ratio and heated oxygen sensors.

·

To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / Data List / All Data / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2; and then press the graph button on the Data List view.


NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ OUTPUT DTC (DTC P0137 or P0157)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0137 or P0157 is output A
DTC P0137 or P0157 and other DTCs are output B


HINT:

If any DTCs other than P0137 or P0157 are output, troubleshoot those DTCs first.




A

2.CHECK FOR EXHAUST GAS LEAK

B

2.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.


HINT:

Perform "Inspection After Repair" after replacing or replacing the exhaust system.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

3.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

NG

REPAIR OR REPLACE EXHAUST GAS LEAK POINT

3.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

4.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C98-1 (HT1B) - C82-18 (HT1B) Always Below 1 Ω
C98-3 (OX1B) - C84-9 (OX1B) Always Below 1 Ω
C98-4 (E2) - C84-10 (EX1B) Always Below 1 Ω
C97-1 (HT2B) - C82-13 (HT2B) Always Below 1 Ω
C97-3 (OX2B) - C84-3 (OX2B) Always Below 1 Ω
C97-4 (E2) - C84-4 (EX2B) Always Below 1 Ω
C98-1 (HT1B) or C82-18 (HT1B) - Body ground and other terminals Always 10 kΩ or higher
C98-3 (OX1B) or C84-9 (OX1B) - Body ground and other terminals Always 10 kΩ or higher
C97-1 (HT2B) or C82-13 (HT2B) - Body ground and other terminals Always 10 kΩ or higher
C97-3 (OX2B) or C84-3 (OX2B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE HEATED OXYGEN SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE HEATED OXYGEN SENSOR
a.

Result:
Proceed to
NEXT



NEXT

6.PERFORM CONFIRMATION DRIVING PATTERN
6.PERFORM CONFIRMATION DRIVING PATTERN
a.

Perform the Confirmation Driving Pattern.


Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0137 OR P0157)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0137 OR P0157)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 234 20

e.

Input the DTC: P0137 or P0157.


f.

Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the driving pattern again but increase the vehicle speed.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P0137 or P0157 is output)
B


HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




A

END

B